31A-230 BP-' 022-1321
20 HARRISON AVE COMMONWEALTH OF MASSACHUSETTS
Map:Block:Lot:
31A-230-001 CITY OF NORTHAMPTON
Permit: Solid Fuel
Appliance
PERSONS CONTRACTING WITH UNREGISTERED CONTRACTORS
DO NOT HAVE ACCESS TO THE GUARANTY FUND (MGL c.142A)
BUILDING PERMIT
Permit # BP-2022-1321 PERMISSION IS HEREBY GRANT, D TO:
Project# PELLET STOVE Contractor: License:
Est. Cost: DOUGLAS L'ABBEE CSL99401
Const.Class: Exp.Date: 01/06/2024
Use Group: Owner: DRIMMER QUINN, CASEY & SONJA
Lot Size (sq.ft.)
Zoning: URB Applicant: THE FIRE PLACE
Applicant Address Phone: Insurance:
100 STATE RD (413)397-3463 01400503301116
WHATLEY, MA 01093
ISSUED ON: 10/13/2022
TO PERFORM THE FOLLOWING WORK:
PELLET STOVE
POST THIS CARD SO IT IS VISIBLE FROM THE STREET
Inspector of Plumbing Inspector of Wiring D.P.W. Building Inspector
Underground: Service: Meter: Footings:
Rough: Rough: House # Foundation:
Final: Final: Final: Rough Frame:
Gas: Fire Department Driveway Final: Fireplace/Chimney:
Rough: Oil: Insulation:
Smoke: Final:
THIS PERMIT MAY BE REVOKED BY THE CITY OF NORTHAMPTON UPON VIO ATION OF
ANY OF ITS RULES AND REGULATIONS.
Signature:
Fees Paid: $40.00
212 Main Street,Phone(413)587-1240,Fax: (413)587-1272
Office of the Buildine Commissioner
City of Northampton
°µ�a`rcr'�,,, 5�5 °' ,s`f-,
€ Massachusetts w t _ l{'1
4iq
�i' y°���` ,r,_N i DEPARTMENT OF BUILDING INSPECTIONS �: •'-;
` ' '` 212 Main Street • Municipal Building
�; ` Northampton, MA. 01060 sl'ii, **P_,`
3-0--- 2.3 o /APPLICATION FOR SOLID FUEL APPLIANCE INSTALLAT N; /
VOci
im.
0
Property Information "0,97-4.4co/N 0
Owners Name: 1I Sc• 63cii h Tv) l0 '44 ecrioNs
Address: (96' Nor-in /9re A/oaf A0v),t/arl d14 69 o't O
(No.) (Street Address)
Phone: 9/1 WV- ?Vac' Cell: Email:
•
Owners Signature: Date: 9/i4-1
Contractor's Information (If Applicable)
Name: Dav94 S L'P hc-c_ Phone: zit 3 . ' '-
Construction Supervisor's License #: 990 Expiration: (K.-2c/
Home Impr. Contractor License #: / ,Fo c/77 Expiration: // /t.2
Stove Information
Type of Fuel (check all that apply): Wood Pellet Coal
Location: iCi,4 f/c13r Freestanding Insert .--
Manufacturer: d.f r) Model: eeccenit9 5 t ,ins-rf
J ,I F -x ss finer //I'41 H&c_
FOR BUILDING DEPARTMENT USE ONLY ,�f---- ---
Permit# 6� 1)-- I'3 1 Date Applied: • Total all Fees: $ liv 10a T
1
Building Official: evil..) `KDzS Date Issued: /0- 1320ZZ
(Print)
Signature of Building Official: •
. �.m a fit.. c.,/, YG{4lCf6 tej Sru..4J.y44a..6s4uc6c.r
^;1 �. Department of Industrial Accidents
-': •1;r: Office of Investigations
:,,�--rp r^:'; Lafayette City Center
=','= t_L:' 2 Avenue de Lafayette, Boston,MA 02111-1750
.•'•'' www.11iass onv/did(
Workers' Compensation Insurance Affidavit: Builders/Contractors/Electricians/Plumbers
applicant Information Please Print Legibly
game (Business/Organization/individual):THE FIRE PLACE
ddress:100 STATE ROAD
-2ity/State/Zip:WHATELY, MA 01093 Phone#:413-397-3463
re you an employer? Check the appropriate box: Type of project(required):
® I am a employer with 10 4. ❑ I am a general contractor and I
employees (full and/or part-time).* have hired the sub-contractors f• ❑ New construction
❑ i am a sole proprietor or partner- listed on the attached sheet. 7. ❑Remodeling
ship and have no employees These sub-contractors have g• ❑ Demolition
working for me in any capacity. employees and have workers' 9. ❑ Building addition
[No workers' comp.insurance comp. insurance.$
required.] 5. ❑ We are a corporation and its 10.❑ Electrical repairs or additions
❑ I am a homeowner doing all work officers have exercised their 11.1:1 Plumbing repairs or additions
myself. [No workers' comp. right of exemption per MGL 12.❑Roof repairs
insurance required.] ( c. 152, §1(4), and we have no
employees. 1:No workers' 13.E Other
comp. insurance required.]
ry applicant that checks box#1 must also fill out the section below showing their workers'compensation policy information.
omeowners who submit this affidavit indicating they are doing all work and then hire outside contractors must submit a new affidavit indicating such.
utractors that check this box must attached an additional sheet showing the name of the sub-contractors and state whether or not those entities have
dovees, If the sub-contractors have employees,they must provide their workers'comp.policy number.
in an employer that is providing workers'compensation insurance for my employees. Below is the policy and job site
orrnation.
rurance Company Name:MA RETAIL MERCHANTS WC GROUP INC
hey#or Self ins.Lie.#:01400503301116 Expiration Date:1-1-23
•b Site Address: —rQ h/�rrri Son ll 6/Ow
- �✓e City/State/Zip: We/WI t,ru
:tack a copy of the workers' compensation policy declaration page(showing the policy number and expiration date).
ilure to secure coverage as required under Section 25A of MGL c. 152 can lead to the imposition of criminal penalties of a
le up to S1,500.00 and/or one-year imprisonment, as well as civil penalties in the form of a STOP WORK ORDER and a tine
up to S250.00 a day against the violator. Be advised that a copy of this statement may be forwarded to the Office of
vestigations of the DIA for insurance coverage verification.
to hereby certif iya er the pains an f pen !ties of perjury that the information provided above is true and correct.
mature: �J Date: ' f0. 3-4'2'
lone#: 413-397-3463 •
Official use only. Do not write in this area,to he completed by city or toxin official.
City or Town: Permit/License#
Issuing Authority(check one):
1❑Board of Health 2❑Building Department 30City/Town Clerk 4.0 Electrical Inspector S❑Plumbing
Inspector 6.0Other
Contact Person: Phone#: _
3 Clearances
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only.
- 24-7/8" -i
NM -
Ir-:- . :.-._- it
`II
? --- 1/
I.
Y Q, .I
N• O1 • 14-3/r
ry
A A
I v
43 44 A 12-3/4"
v v To Top Edge
cT,
a a. a r� 22-3/4"
Measured from steel stove body
I• I I
10-1/2"�
N ry N To Glass
✓ v v
W I. N.
0 0 0
rn 9' a
ac ; a
1 '
r+ '�- I 'IlilllllyllllI I�I IIIIIIIIIIIIII !
Ilti IL
iMai=01111.111111/EDINP
''''. . .
,c. co
1 .5 .-
Zo I... WI en
h N N k, c 'i ] ' !t
11:7 1... 7:-',7::: 7-t7::f,*----',.::.7:-.:::7: I 0, 'fii:. 1
1/--:\ r---i___--- ,(=
II
_ f
I 1 U�lllllllllu,lip,I 9 U�llllllllllu c
-- - INIIII' I
.I...... - ._— ill IIII..lihuu,,.�unll T '
-..--1 i--..-13/16"
15-9/16" - -F—14-3/8"
29-15/16" 41-13/16"
Figure 3.1
8 Harman® • Accentra52i-TC Installation Manual_R15 • 2017- • 06/21 3-90-005841
B. Clearances to Combustibles&Floor Protection
When selecting a location for the appliance it is important to NOTICE:Illustrations reflect typical installations and are FOR
consider the required clearances to walls (see Figure 3.2). DESIGN PURPOSES ONLY. Illustrations/diagrams are not
WARNING! Risk of Fire or Burns! Provide adequate drawn to scale.Actual installation may vary due to individual
clearance around air openings and for service access. Due design preference.
to high temperatures, the appliance should be located out of
traffic and away from furniture and draperies.
* Floor protection must be used from hearth opening to 6" (152mm) in front of door glass and 6" (152mm)to each side
of the stove body OR 8" (203mm) to sides to protect combustibles from hot ashes. A minimum size will be 16.5" deep
by 30"wide and be made of a non-combustible material or meet UL approval.
Clearances: A B *C *D E (From Glass)
From Insert Body: 12" (305 mm) 12" (305 mm) 0" 0" 6" (152 mm)
*3/4 Trim, Zero Clearance to Cast Surround
A =to sidewall �
B = to 12" mantel 12(305mm)Mantel
C = to 3/4"trim
D = to 3/4"trim 1
E =floor protection % '1 -41111111
i.-- --
___ICI_l • 11�-� r 1
,ra,- r""___:-_77:7--Ir 'xi
==1 I p =
E E
Figure 3.2
C. Minimum Opening - Masonry and Manufactured Fireplaces
Location Inches Millimeters
F Minimum Width 24-7/8 632
G Minimum Depth 15-9/16 395
G H Minimum Height#1-90-574240 24 610
H H Minimum Height#1-90-574220 22 779
H Minimum Height#1-90-574200 20 508
/ F \
/
9 Harman® • Accentra52i-TC Installation Manual_R15 • 2017- • 06/21 3-90-005841
4 Termination Location and Vent Information
4 A. Vent Termination Requirements Chimney connector shall not pass through an attic or roof
space,closet or similar concealed space,or a floor or ceiling.
D A
Inside Corner
L Detail
43_
B °Oa ® rleed �/ f B_^ porch or Deck
Cb ed
L ` D _ % /� �bk Cloud_c® Open able Fi ed
F I.
`//,00en.ae B jj I 61111111
A /////// C �1�������I
Sidewalk -+B 'J I A M
A K � �
1 'T
0=Vent Terminal O=Air Supply Inlet % =Area where termination is not permitted
WARNING: Venting terminals must not be recessed into a I.The clearance to service regulator vent outlet must be a
wall or siding. minimum of 6 feet.
NOTE: Only PL or L vent pipe wall pass-throughs and fire J.The clearance to a non-mechanical air supply inlet to
stops should be used when venting through combustible the building or the combustion air inlet to any other
materials. appliance must be a minimum of 48".
NOTE:Always take into consideration the affect the K.The clearance to a mechanical air supply inlet must be
prevailing wind direction or other wind currents will cause a minimum of 10 feet. (with outside air installed, 6
with flyash and/or smoke when placing the termination. feet)
In addition,the following must be observed: L. The clearance above a paved sidewalk or a paved
A. The clearance above grade must be a minimum of 12". driveway located on public property must be a minimum
of 7 feet.
B. The clearance to a window or door that may be opened
must be a minimum of 48"to the side and 48" below M.The clearance under a veranda, porch, deck or balcony
the window/door, and 12" above the window/door. (with must be a minimum of 12". (B. also)
outside air installed, 9"to side and below) NOTE: The clearance to vegetation and other exterior
C.A 12" clearance to a permanently closed window is combustibles such as mulch is 36"as measured from the
recommended to prevent condensation on the window. center of the outlet or cap.This 36" radius continues to
grade or a minimum of 7 feet below the outlet.
D.The vertical clearance to a ventilated soffit located
above the terminal within a horizontal distance of 2 feet Certain Canadian and or Local codes or regulations may
(607mm)from the center-line of the terminal must be a require different clearances.
minimum of 18". A vent shall not terminate directly above a side-walk
E. The clearance to an unventilated soffit must be a or paved driveway which is located between two
minimum of 12". single family dwellings and serves both dwellings.
F.The clearance to an outside corner is 11"from center of Only permitted if veranda, porch, deck, or balcony is fully
pipe. open on a minimum of 2 sides beneath the floor.
G.The clearance to an inside corner is 12". See NFPA211 for more installation clearance reductions
when using outside air.
H. A vent must not be installed within 3 feet(914mm)
above a gas meter/regulator assembly when measured NOTE: In Canada, where passage through a wall or
from the horizontal center-line of the regulator. partition of combustible construction is desired, the
installation shall conform to CAN/CSA-B365.
10 Harman® • Accentra52i-TC Installation Manual_R15 • 2017-_ • 06/21 3-90-005841
B. Venting Termination Design #1 Installing into an existing fireplace chimney
The chimney top must be capped to This method provides excellent venting with 00%outside air
"r'r�� prevent rain and/or snow from entering which is the most efficient operation of this unit.This method
three
he chimney. also provides natural draft in the event of a bower failure.
See Figure 4.8, for information on the A4"stainless steel flex pipe is needed for the flue pipe,and 3"
optional Harman®Adjustable Stainless aluminum or Stainless Steel Flex Pipe is used for the intake.
Steel Intake Extension.
A WARNING
The damper area must be sealed with CHIMNEY CONNECTOR PIPE MAY, NOT PASS
a non-combustible material and it is THROUGH CONCEALED SPACES INCLUDING AN
recommended that Kaowoll, mineral ATTIC, ROOF SPACE, CLOSET, FLOOR OR CEILING.
wool, or an equivalent non-combustible
insulation be placed on top of the
sealed area to reduce the possibility of A WARNING
,7,..,___, -
condensation. Insulation alone should
not be used to seal the damper opening.
For quick and easy installation, purchase DO NOT REMOVE BRICKS OR MORTAR FROM
the steel Harman Block Off Plate, 1-00- THE EXISTING FIREPLACE.
• 25625.
II II �'`i
`., 1 I
— Height of existing hearth
Figure 4.1
a.
im
rr..r.rrr
The chimney top must be capped to #2 Installing into an existing fireplace chimney
'I_II prevent rain and/or snow from entering
the chimney. This method provides excellent venting for normal operation.
This method also provides natural draft irl the event of a
power failure.
A cap should be installed on the chimney tc� keep out rain.
Combustion air is provided from the living arda and enters the
The damper area must be sealed with feed system from around the wing and stove body spaces.
a non-combustible material and it is
recommended that Kaowoll, mineral A WARNING
wool, or an equivalent non-combustible
- insulation be placed on top of the
sealed area to reduce the possibility of DO NOT REMOVE BRICKS OR MORTAR FROM
-. condensation. Insulation alone should THE EXISTING FIREPLACE.
not be used to seal the damper opening.
For
quick
easy
lation, purchase
\ t e steel Hadrman Block lOff Plate, 1-00-
hi
25625.
M.! l ii.-
:Fri 1
114
Figure 4.2
11 Harman® • Accentra52i-TC Installation Manual R15 • 2017- • 06/21 3-90-005841