23D-156 BP-2022-0108
150 MAPLEWOOD TERR COMMONWEALTH OF MASSACHUSETTS
Map:Block:Lot:
23D-156-001 CITY OF NORTHAMPTON
Permit: Solid Fuel
Appliance
PERSONS CONTRACTING WITH UNREGISTERED CONTRACTORS
DO NOT HAVE ACCESS TO THE GUARANTY FUND (MGL c.142A)
BUILDING PERMIT
Permit # BP-2022-0108 PERMISSIONIS HEREBY GRANTED TO:
Project# WOOD STOVE Contractor: License:
Est. Cost: DOUGLAS L'ABBEE 99401
Const.Class: Exp.Date:01/06/2024
Use Group: Owner: ALVORD, CALEB &JOCELYN
Lot Size (sq.ft.)
Zoning: URB Applicant: THE FIRE PLACE
Applicant Address Phone: Insurance:
PO BOX 606 (413)397-3463 014005033011 16.
WHATLEY, MA 01093
ISSUED ON:02/04/2022
TO PERFORM THE FOLLOWING WORK:
WOOD INSERT
POST THIS CARD SO IT IS VISIBLE FROM THE STREET
Inspector of Plumbing Inspector of Wiring U.N.W. Building Inspector
Underground: Service: Meter: Footings:
Rough: Rough: House # Foundation:
Gas: Final: Final: Rough Frame:
Rough: Fire Department Driveway Final: Fireplace/Chimney:
Final: Oil: Insulation:
Smoke: Final:
THIS PERMIT MAY BE REVOKED BY THE CITY OF NORTHAMPTON UPON VIOLATION OF
ANY OF ITS RULES AND REGULATIONS.
Signature: 1 yrrJJn
y . �
I
Fees Paid: S40.00
212 Main Street,Phone(413)587-1240,Fax:(413)587-1272
Office of the Building Commissioner
__ City of Northampton
'' - t Massachusetts w ,{-
i ' I 6 ,,, DEPARTMENT OF BUILDING INSPECTIONS r,
212 Main Street • Municipal Building 4
\\ 1 Northampton, MA 01060 j:4%"7,;i-jt1CS.
1.- _CE—
APPLICATION FOR SOLID FUEL APPLIANCE INSTALLATIO;NN 3 1 J
N rOF 8U11_
1 ^'OgTH,"�iIO !NSPECTIONS
Property Information ' 6o
010
Owners Name: ( /eh >9Lvirzr,
Address: /5-0. mAn/c%brtr) ryaec / F/or,fve ,71 oy/ za
(No.) (Street Address)
Phone: '//3-6'S-j ^77 C 11: Email:
Owners Signature: Date: 4\9-1
Contractor's Information (If Applicable)
Name: aa0'/43 L A - Ve l: c ?/occ._ Phone: 14 �fr 3'6 S
Construction Supervisor's License #: 9?'f/-0/ Expiration: 7--G - goz-ri
Home Impr. Contractor License #: /ids/77 Expiration: //-if`•aoa '
Stove Information
Type of Fuel (check all that apply): Wood Pellet Coal
Location: r"i rsr AT r Freestanding Insert X'
Manufacturer: ALr,dem Model: S:5,2o fr -r4
/"n5i*IIi r? 1(1 ?V& c SS--/i`/nc-r'
n q FOR BUILDING DEPARTMENT USE ONLY------------ ------) /--- -
ga
Permit# Q ' ��d 0 Date Applied: Total all Fees: $ 11(/
Building Official: Date Issued: 2. 9 2
(Print)I1 () ,Tjt,7(
Signature of Building Official:
I
_ The Commonwealth of Massachusetts
=Ai
'"° r, Department of Industrial Accidents
e,�1_ 1 Congress Street,Suite 100
___ Boston,MA 021I4-2017
w.
r,
www.mass.gov/dia
Workers'Compensation Insurance Affidavit:Builders/Contractors/Electricians/Plumbers.
TO BE FILED WITH THE PERMITTING AUTHORITY.
Applicant Information Please Print Legibly
Name(Business/Organization/Individual): /C i;fe ''�ff C'L
Address: /60 5>tc �a4f)
City/State/Zip: Aief,f, o/O '5 Phone#: Vf 3 7 7 . .$G -3
Are you an employer?Check the appropriate box: Type of project(required):
1.Z I am a employer with /0 employees(full and/or part-time).* 7. 0 New construction
2.0 I am a sole proprietor or partnership and have no employees working for me in 8. p Remodeling
any capacity.[No workers'comp.insurance required.]
3.0 I am a homeowner doing all work myself.[No workers'comp.insurance required.]'
9. El Demolition
10 ❑Building addition
4.0 I am a homeowner and will be hiring contractors to conduct all work on my property. I will
ensure that all contractors either have workers'compensation insurance or are sole 11.0 Electrical repairs or additions
proprietors with no employees.
12.0 Plumbing repairs or additions
5.0 I am a general contractor and I have hired the sub-contractors listed on the attached sheet. 13.nR00f repairs
These sub-contractors have employees and have workers'comp.insurance.
6.0 We are a corporation and its officers have exercised their right of exemption per MGL c. 14.Q Other
152,§1(4),and we have no employees.[No workers'comp.insurance required.)
*Any applicant that checks box#1 must also fill out the section below showing their workers'compensation policy information.
t Homeowners who submit this affidavit indicating they are doing all work and then hire outside contractors must submit a new affidavit indicating such.
Contractors that check this box must attached an additional sheet showing the name of the sub-contractors and state whether or not those entities have
employees. If the sub-contractors have employees,they must provide their workers'comp.policy number.
I am an employer that is providing workers'compensation insurance for my employees. Below is the policy and job site
information.
Insurance Company Name: Oil f) grovL piEigCNa T'S 6726°V7D/Ate
Policy#or Self-ins.Lic.#: C/9 e10Co 3 'o///t Expiration Date: //--. .3
Job Site Address: /5 /'rl,//gahro /---
rr City/State/Zip: /ofc flCZ /� d IOC a
Attach a copy of the workers' compensation policy declaration page(showing the policy number and expiration date).
Failure to secure coverage as required under MGL c. 152,§25A is a criminal violation punishable by a fine up to$1,500.00
and/or one-year imprisonment,as well as civil penalties in the form of a STOP WORK ORDER and a fine of up to$250.00 a
day against the violator.A copy of this statement may be forwarded to the Office of Investigations of the DIA for insurance
coverage verification.
I do hereby certify nder the pains and p nalties of perjury that the information provided above is true and correct.
Sienature: xR Date: / •027'/a"
Phone#: W3 3l T 34' '
Official use only. Do not write in this area,to be completed by city or town official.
City or Town: Permit/License#
Issuing Authority(circle one):
1.Board of Health 2.Building Department 3.City/Town Clerk 4.Electrical Inspector 5.Plumbing Inspector
6.Other
Contact Person: Phone#:
.i
J ,
_a
3
CD
M
Cil
G'
cn
TOP VIEW FRONT VIEW RIGHT SIDE VIEW
A
51/4" 10 34"
(134mm)-(273mm) C B
41"(1o41mm)
613/16" 125/16" 111/2" •-17"
(173mm)-(313mm) (292m)-(432m )
25 3/8"
(645mm) `
30"
• (762mm)
4 1/2"
1 i
T 0 r " ITE I mural
9 3/4" .
(248mm) ..�, a)1/2"
(521mm) 21 3/4"
I - 115 5/8" ' (552mm)
(398mm)
� ■
I, ii mi. 0
i ..i
_ I- mal '
26 1/2"
(673mm) 1
CO
OD
CD
m1
note: a)
A
Due to an adjustable air channel, A, B and C are adjustable in 3/8" (9.5mm) increments (see
"specifications" section for min max). .
co
wi
o 3
cri
0 co
01 n
,
EN 2.0 installation planning
Clean all ashes out of the inside of the existing fireplace opening. Make sure that the chimney and fireplace are free
of cracks, loose mortar, creosote deposits, blockage or other signs of deterioration. If necessary, have any repair
work done by a qualified professional before installing the insert.
Do NOT remove bricks or mortar from the fireplace. In case of an outside air inlet or ash dump, fill with fiberglass
insulation. Adhere to minimum clearances as illustrated.
Combustible material must not protrude more than 1" (25mm)to the side of the insert or between the mantel and
the top of the insert.
2.1 minimum clearance to combustibles
MINIMUM CLEARANCES
A Sidewall 16" (406mm)
B Mantel 30" (762mm)
C Top facing 22" (559mm)
D Side facing 10" (254mm) °p^4 u2,,,e
'-- MANTEI
E Hearth (front) 22" (559mm) /
^crpn
F Minimum hearth ti
thickness 1" (25mm)
G Hearth (side) 8" (203mm)
H In front of insert 48" (1219mm)
MINIMUM EXISTING
FIREPLACE DIMENSIONS
I Width (rear)
25 7/8" (657mm)
J Width (front)
K Height(front) •
22" (559mm) '
L Height(rear) H � "° MA ,� ,
M Depth 14" (356mm) 11OT°l*L.
N Hearth width 41 3/8" (1051 mm)
O Facing width 45 3/8" (1153mm)
P Facing height 42 5/8" (1083mm)
Q Mantel 50 5/8" (1286mm)
\\� MgNTEL
HEARTH EXTENSION / FLOOR
PROTECTION: NQN coo-acSTi
Must be non-combustible and extend 22" �`�
0
(559mm) in front of the insert and 8" (203mm)
on both sides with.a minimum thickness of 1"
(25mm)and a thermal conductivity factor(K)
0.84. K
Clearances can be reduced with shielding
acceptable to local authorities. Reduced
installation must comply with NFPA 211 or
CAN/CSA-B365.
Mg
1 O I W415-2797 r'D/05.07.21
3.0 installation EN
• Wear gloves, protective footwear and safety glasses for protection.
• Carefully follow the instructions for assembly of the pipe and other parts needed to install the appliance.
Failure to do so may result in a fire, especially if combustibles are too close to the appliance or chimney and air
spacers are blocked, preventing the free movement of cooling air.
• Do not draw outside air from garage spaces. Exhaust products of gasoline engines are hazardous. Do not
install outside air ducts such that the air may be drawn from attic spaces, basements or above the roofing
where other heating appliances or fans and chimneys exhaust or utilize air.These precautions will reduce the
• possibility of appliance smoking or air flow reversal. The outside air inlet must remain clear of leaves, debris, ice
and/or snow. It must be unrestricted while appliance is in use to prevent room air starvation which can cause
smoke spillage and an inability to maintain a fire. Smoke spillage can also set off smoke alarms.
• Negative pressure within your home may inadvertently affect your appliance.
To prevent contact with sagging or loose insulation,the appliance must not be installed against vapour barriers
• or exposed insulation. Localized overheating could occur and a fire could result.
• Do not use makeshift compromises during installation. Do not block or restrict air, grille or louvre openings. Do
not add a hood.
• To prevent personal injury, keep hand tools in good condition, sharpen cutting edges and make sure tool
s handles are secure.
• Always maintain the minimum air space required in the enclosure to prevent fires.
• Check with local building officials for, any permits required for installation of this appliance and notify your
• insurance company prior to proceeding.
It is extremely important that your appliance be installed according to the manufacturer's specifications.The
manufacturer's installation instructions and specified clearances should always be followed in accordance with
local and national codes. In Canada the CSA B365 and the CSA C22.1 installation codes are to be followed. In
the USA the ANSI NFPA 70 and ANSI NFPA 211 installation codes are to be followed.
Chimney and liner must be in good condition and kept clean.
W415-2797/D i 05.07.21 111
, installation
3.1 typical existing masonry
You can install your appliance using your existing masonry FOLLOW MANU-
chimney. To do so, use the following guidelines. If you are using a mon=
mom= FACTURER'S
masonry chimney, it is important that it be built in compliance with IIII■IM INSTRUCTIONS
the specifications of the Building Code in your region. It � FOR MAXIMUM
must normally be lined with fire clay bricks, metal or clay — . � 7 LINER EXTENSION
tiles sealed together with fire cement. (Round flues are ��� onABOVE CHIMNEY
the most efficient). MASONRY �'Illm ii=
CHIMNEY sm .-
MUST HAVE im INE`)
STRUCTURAL im um
INTEGRITY =i =1
'- 12
LISTED
—� • CHIMNEY
:" 1M LINER
Mar ;NI
SE ll
SEAL WITH id■ •V�.m DAMPER PLATE
NON-COMBUSTIBLE tam REMOVED OR
MATERIAL El FASTENED IN
mim OPEN POSITION
i E'
FLOOR .�I
mIMI
PROTECTOR Emi
—I—
■..■rr...■■■_smom■.._.
A. Remove the fireplace damper or fasten it permanently open.
We recommend the following method of sealing off the damper area around the liner.
B. * Measure the throat of the fireplace and mark this shape on a piece of 24 gauge sheet metal (flue cover);
cut a six-inch (6.75"/ 171 mm) hole to lie directly below the fireplace flue opening. Allow two inches of
material for a flange on all sides and cut to these measurements. Bend down the flanges. If you have never
done this before, it might be a good idea to make a cardboard pattern and test it first. Fasten this flue cover
in position as high as possible with two masonry screws per side through the flanges into the fireplace.
In Canada: Install a listed 6" (152mm) diameter flexible stainless steel liner from the top of the chimney to the insert
flue collar. Attach a stainless steel liner connector or elbow to the liner and insert onto the flue collar. Fasten with
three screws. Secure the top of the liner to the chimney cap using a liner support and chimney flashing. Cap the top
of the chimney liner assembly using an approved rain cap.
note:
This fireplace insert must be installed with a continuous chimney liner of 6" (152mm) diameter extending from
the fireplace insert to the top of the chimney. The chimney liner must conform to the Class 3 requirements of
CAN/ULC-S635, Standard for Lining Systems for Existing Masonry or Factory-Built Chimneys and Vents, or
CAN/ULC-5640, Standard for Lining Systems for New Masonry Chimneys.
In the United States:While it is not required, it is recommended that a chimney liner be installed that is continuous
from the insert to the top of the chimney, particularly when the insert is installed in a basement. For this type of
connection, use the"In Canada" installation instructions above.
If a continuous liner is not installed, a"direct flue connection" must be made. The direct flue connection requires a
non-combustible connector that extends from the insert into the chimney flue liner and also that the installed flue
cover be sealed below the entry point of the connector to prevent dilution of combustion products in the chimney
flue with air from inside the house. Cap the top of the chimney using an approved rain cap.
The following installation requirements must be observed when installing solid fuel burning inserts into factory built
fireplaces.
12 ,:nva