Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Neiman-Planset
RELEASEREVDATE NAMEGOVERNING CODESPARCEL MAP PROJECT LOCATION SHEET INDEX ENGINEERED BY: CONTRACTOR: CONTRACTOR LIC #: PHONE: CONTACT NAME: PHONE: EMAIL: DESIGN BY: PHONE: HOME OWNER PROJECT LOCATION: PROJECT DRAFTER: LICENSE #: PHONE: ELECTRICAL UTILITY: AUTHORITY HAVINGJURISDICTION: BUILDING: CONTACT NAME:PHONE: LICENSE TYPE: PHONE: EMAIL: EMAIL: PHONE:COVER SHEETSHEET SHEET TITLE EMAIL:APNAdvanced Solar Solutions39650 MallardBass Lake, CA 93604 PHONE: 559-321-7000EMAIL: info@advpermits.com ADDRESS ADDRESS kW PHOTOVOLTAIC PLANS PROJECT APN: GENERAL PROJECT & JURISDICTIONAL NOTES 1. UNAUTHORIZED USE OF THIS DRAWING SET WITHOUT EXPRESSEDWRITTEN PERMISSION FROM THE CONTRACTOR AND ADVANCED SOLAR SOLUTIONS IS A VIOLATION OF U.S. COPYRIGHT LAWS AND WILL BE SUBJECTTO CIVIL DAMAGES AND PROSECUTION. APPLICABLE BUILDING CODES: INTERNATIONAL BUILDING CODE INTERNATIONAL RESIDENTIAL CODE INTERNATIONAL FIRE CODE NATIONAL ELECTRIC CODE DESIGN CRITERIA BUILDING OCCUPANCY: RISK CATEGORY: EXPOSURE CATEGORY: SNOW LOAD: SNOW EXPOSURE: CONSTRUCTION TYPE: SCOPE OF WORK NUMBER PROPOSED SOLAR EQUIPMENT SITE / PROJECT DETAILS QTY. EQUIPMENT DESCRIPTION/MFG/MODEL MODULES INVERTER(S) RACKING STANCHIONS RSD DEVICE BATTERIES SYSTEM SIZE DC SYSTEM SIZE AC QTY. STRING/CKT. ELECT. SERVICE PROJECT TEAM LIST COPYRIGHT NOTICE 1. A LADDER SHALL BE IN PLACE FOR INSPECTION IN COMPLIANCE WITH ALL OSHA REGULATIONS. 2. PENDING LOCAL JURISDICTIONAL REQUIREMENTS AND WHEN APPLICABLE ALL ELECTRICAL ENCLOSURE DEAD FRONTS, COVERS, DOORS, ETC. SHALE BE OPEN AND ACCESSIBLE FOR INSPECTIONS. WHEN TRENCH AND ROOF INSPECTIONSARE REQUIRED WORK SHALL BE OPEN AND ACCESSIBLE FOR INSPECTOR. INSPECTION REQUIREMENTS 1. WHEN APPLICABLE A SMOKE DETECTOR, APPROVED AND LISTED BY THE STATE FIRE MARSHAL OR ANSI/UL 217 CERTIFIED TO NATIONAL FIRE ALARM AND SIGNALING CODE, NFPA 72 SHALL BE VERIFIED FUNCTIONAL OR INSTALLED IN ALL APPLICABLE CODE REQUIRED LOCATIONS. 2. ALL APPLICABLE EQUIPMENT TO BE UL LISTED OR LISTED BY OTHERJURISDICTIONAL AND UTILITY APPROVED ASSOCIATION OR NATIONALLY RECOGNIZED ORGANIZATION. 3. FULL SCOPE OF WORK SHALL COMPLY WITH ALL APPLICABLE CODES LISTEDIN GOVERNING CODES SECTION, ALL MANUFACTURES' LISTINGS, INSTALLATION INSTRUCTIONS AND SPECIFICATIONS AND JURISDICTIONAL REQIREMENTS. JURISDICTIONAL & LISTING REQUIREMENTS 4. REVISED PLANS WILL BE REQUIRED TO BE RESUBMITTED TO THE LOCALJURISDICTION IF THE INSTALLED ARRAY AND ASSOCIATED EQUIPMENT DOES NOT MATCH THE APPROVED BUILDING PLANS. ADDITIONAL FEES MAY ALSOAPPLY. 5. THE PLACEMENT OF A UTILITY PV PRODUCTION METER SHALL BE PROVIDED AND PLACED BY THE CONTRACTOR AS PER APPLICABLE UTILITY OR AHJREQUIREMENTS. MSP RATINGS AZIMUTH TILT STANCHIONS NORTH DRIVEWAY ℄RIVERSIDE DR ⅊ ⅊ ⅊ ⅊ N/A VB 12.540 KW PV-001 COVER SHEET Neiman, Anna Steven Silverman 2015 National Grid 2015 38103355 2015 21134A(413) 584-8844 2020 Lilian Wanjiku(413) 584-8844 City of Northampton jstocker@valleysolar.solar 50507Civil(202) 874-3483swyssling@wysslingconsulting.com R-3 Risk Category II Exposure C 40 Scott E. Wyssling 76 North Meadowbrook DrAlpine, UT 84004 Neiman, Anna284 Riverside Dr, Northampton, MA 01062 ROOF MOUNTED PV (SOLAR) PROJECT GRID-TIED W/ BATTERY STORAGE 340 Riverside Dr Valley Solar Florence, MA 01062 Hanwha Q-cells Q.PEAK DUO-G7 330 GENERAC PWRcell 7.6 APKE00014SnapNrack Ultra Rail UR-60Zilla Double Stud XLSnapnrack 242-01220 L Foot Generac PWRcell 17 38 1 N/A7356 1 N/A (N) GPS LOCATION:42.3279672, -72.66996329999999 11.239 KW 5 120/240V - 1 39.8°,33.6° 236° ROOF COVERING MAX ARRAY HGT. 117 N/AComp Shingle N-001 GENERAL NOTES PV-100R PV ARRAY LAYOUT S-100 RACKING LAYOUT S-200 SECTION ELEVATION S-201 ATTACHMENT DETAILS E-001 EQUIP. CALCULATION METER NUMBER: E-002 WIRE AND COND. CALCS E-003 THREE LINE DIAGRAM E-100 ELECTRICAL LAYOUT P-001 STANDARD PLACARDS P-002 DYNAMIC PLACARDS R-1xx EQUIP.CUT SHEETS S202 SECTION ELEVATION S-203 ATTACHMENT DETAILS INTEGRATED IN INV & OPT 225A BUS/200A MAIN BREAKER BACK-FEED PV-001ASCE 7-10 WIND SPEED:Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT RELEASEREVDATE NAME ADDRESSAPNGENERAL NOTES ADDRESS kW PHOTOVOLTAIC PLANS GENERAL NOTES:* PROPER ACCESS AND WORKING CLEARANCE AROUND EXISTING AND PROPOSED ELECTRICAL EQUIPMENT WILL BE PROVIDED AS PER SECTION NEC 110.26. PV SYSTEM COMPONENTS; INCLUDING BUT NOT LIMITED TO, MODULES, INVERTERS AND SOURCE CIRCUIT COMBINERS ARE IDENTIFIED AND LISTED FOR USE IN PV SYSTEMS IN COMPLIANCE WITH NEC 690.4 AND 690.6 AND ALL UL, IEC, IEEE CLASSIFICATIONS AS REQUIREMENTS. RAPID SHUTDOWN NOTES:* PV SYSTEM CIRCUITS INSTALLED ON OR IN BUILDIDNG SHALL INCLUDE A RAPID SHUTDOWN FUNCTION THAT CONTROLS SPECIFIC PV CONDUCTORS IN ACCORDANCE WITH 2020 NEC 690.12(A)-(D) EQUIPMENT LOCATIONS & ELECTRICAL NOTES:* JUNCTION AND PULL BOXES ARE PERMITTED TO BE INSTALLED UNDER PV MODULES IN COMPLIANCE WITH NEC 690.34. ADDITIONAL AC DISCONNECT(S) SHALL BE PROVIDED WHERE THE INVERTER IS NOT WITHIN SIGHT OF THE AC SERVICING DISCONNECT. 2020 NEC 690.15(A) ALL EQUIPMENT SHALL BE INSTALLED ACCESSIBLE TO QUALIFIED PERSONNEL IN COMPLIANCE WITH NEC APPLICABLE CODES. ALL COMPONENTS ARE LISTED FOR THEIR INTENDED PURPOSE AND RATED FOR OUTDOOR USAGE WHEN APPLICABLE. STRUCTURAL AND INSTALLATION NOTES:* RACKING SYSTEM & PV PANELS MOUNTED ON A ROOFTOP SHALL BE LISTED AND LABELED IN ACCORDANCE WITH UL 1703 AND SHALL BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER INSTALLATION INSTRUCTIONS. ALL PV RACKING ATTACHMENT POINTS SHALL NOT EXCEED THE PRE-ENGINEERED MAX SPANS OUTLINED BY THE RACKING MANUFACTURES ENGINEER OF RECORD. GROUNDING NOTES:* IN UNGROUNDED SYSTEMS ONLY THE DC CONDUCTORS ARE UNGROUNDED AND REQUIRE AN EQUIPMENT GROUNDING CONDUCTOR. ALL METAL ELECTRICAL EQUIPMENT AND STRUCTURAL COMPONENTS BONDED TO GROUND, IN COMPLIANCE WITH NEC 250.134 AND NEC 250.136(A). PV EQUIPMENT INCLUDING MODULE FRAMES AND OTHER METAL PARTS SHALL BE GROUNDED IN COMPLIANCE WITH NEC 690.43 AND MINIMUM GROUND CONDUCTORS SIZED IN ACCORDANCE WITH NEC TABLE 250.122. CONDUCTIVE PARTS OF MODULE FRAMES, MODULE RACKING, AND ENCLOSURES SHALL BE GROUNDED IN COMPLIANCE WITH NEC 250.134 AND NEC 250.136(A). UL2703 APPROVED MODULE AND RACK GROUNDING SHALL BE USED AND INSTALLED PER MANUFACTURER'S INSTALLATION MANUAL. IF UL2703 APPROVED GROUNDING IS NOT USED, MODULE GROUNDING LUGS MUST BE INSTALLED AT THE SPECIFIED GROUNDING LUG HOLES PER THE MANUFACTURER'S INSTALLATION REQUIREMENTS. THE GROUNDING CONNECTION TO A MODULE SHALL BE ARRANGED SUCH THAT THE REMOVAL OF A MODULE DOES NOT INTERRUPT A GROUNDING CONDUCTOR TO ANOTHER MODULE. THE GROUNDING ELECTRODE SYSTEM COMPLIES WITH NEC 690.47 AND NEC 250.50 THROUGH NEC 250.106. IF EXISTING SYSTEM IS INACCESSIBLE OR INADEQUATE, A GROUNDING ELECTRODE SYSTEM WILL BE PROVIDED IN COMPLIANCE WITH NEC 250, NEC 690.47 AND AHJ. PV SYSTEMS SHALL BE PROVIDED WITH DC GROUND- FAULT PROTECTION 2020 NEC 690.41(B) INTERCONNECTION / POC NOTES:* ALL LOAD-SIDE INTERCONNECTIONS ARE IN COMPLIANCE WITH 2020 NEC 705.12(B) THE TOTAL RATING OF ALL OCPD IN SOLAR LOAD CENTERS SHALL NOT EXCEED THE RATED AMPACITY OF THE BUSBAR EXCLUDING THE OCPD PROTECTING THE BUSBAR IN COMPLIANCE WITH NEC 705.12(B)(2)(3)(c) ALL FEEDER TAP (LOAD SIDE) INTERCONNECTIONS ARE IN COMPLIANCE WITH 2020 NEC 705.12(B)(2)(1) THE PV SYSTEM BACK-FEED BREAKER SHALL BE INSTALLED ON THE OPPOSITE END OF THE BUS BAR AND IT SHALL ALSO BE SIZED APPROPRIATELY AS PER 2020 NEC 705.12(B)(2)(3)(b) SUPPLY SIDE TAP INTERCONNECTIONS ARE IN COMPLIANCE WITH NEC 705.12(A) WITH SERVICE ENTRANCE CONDUCTORS IN COMPLIANCE WITH NEC 230.42 BACKFEEDING BREAKER FOR INVERTER OUTPUT IS EXEMPT MICROINVERTER BRANCH CIRCUITS SHALL BE CONNECTED TO A SINGLE OCPD IN ACCORDANCE WITH THEIR INSTALLATION INSTRUCTIONS AND NEC 690.9 DISCONNECTS AND OCPD NOTES:* ALL DISCONNECTING SWITCHES WILL BE CONFIGURED SO THAT ALL ENERGIZED CONDUCTORS WHEN DISCONNECT IS OPEN SHALL BE ON THE TERMINALS MARKED, “LINE SIDE” (TYPICALLY THE UPPER TERMINALS) ALL AC DISCONNECTS SHALL BE LABELED, LOCKABLE, OF VISIBLE BREAK TYPE SWITCH WITH EXTERNAL HANDLE AND ACCESSIBLE TO QUALIFIED UTILITY PERSONNEL. AC DISCONNECTS SHALL BE A “KNIFE BLADE” TYPE DISCONNECT. IF EXTERIOR, RATED TO NEMA 3R OR BETTER PER NEC 110.28 ADDITIONAL AC DISCONNECTS SHALL BE PROVIDED WHERE THE INVERTER IS NOT ADJACENT TO THE UTILITY AC DISCONNECT, OR NOT WIHTIN SIGHT OF THE UTILITY AC DISCONNECT. 2020 NEC 690.15(A) BOTH POSITIVE AND NEGATIVE PV CONDUCTORS REMAIN UNGROUNDED. THEREFORE, BOTH SHALL REMAIN OPEN WHERE A DISCONNECT IS REQUIRED IN COMPLIANCE WITH 2020 NEC 690.15(D) ALL OCPD RATINGS AND TYPES SPECIFIED SHALL BE IN COMPLIANCE WITH NEC 690.8, 690.9, 705.12 AND 240. BOTH POSITIVE AND NEGATIVE DC PV CONDUCTORS ARE UNGROUNDED; BOTH REQUIRE OVERCURRENT PROTECTION IN COMPLIANCE WITH NEC 690.9 ARC FAULT (AFCI) DC CIRCUIT PROTECTION IS REQUIRED FOR ALL PV SYSTEMS ON OR PENETRATING A BUILDING WITH A MAXIMUM SYSTEM VOLTAGE OF 80 VOLTS OR GREATER. ALL DC PV CIRCUITS INSTALLED IN OR ON BUILDINGS WILL BE ARC-FAULT CIRCUIT PROTECTED IN COMPLIANCE WITH NEC 690.11, UL1699B AND SHALL BE LISTED AND LABELED IN ACCORDANCE WITH UL 1699 (B). WIRING & CONDUIT NOTES:* ALL CONDUIT AND CONDUCTORS SHALL BE APPROVED FOR THEIR INTENDED PURPOSE INCLUDING WET LOCATIONS AND EXPOSED TO SUNLIGHT. CONDUIT AND CONDUCTOR SIZE SPECIFICATIONS ARE BASED ON THE MINIMUM CODE REQUIREMENTS AND ARE NOT LIMITED TO UP SIZING. ALL CONDUCTORS SHALL BE SIZED IN COMPLIANCE WITH NEC 690.8, NEC 690.7. ALL CONDUCTORS SHALL BE DERATED AS APPLICABLE TO THEIR RESPECTIVE ENVIRONMENT INCLUDING DIRECT SUNLIGHT IN ACCORDANCE WITH 2020 NEC 310.15(B)(3)(4)(c) EXPOSED UNGROUNDED DC PV SOURCE AND OUTPUT CIRCUITS SHALL USE CONDUCTORS LISTED AND IDENTIFIED AS PHOTOVOLTAIC (PV) WIRE IN COMPLIANCE 2020 NEC 690.31(C)(1). PV MODULES WIRE LEADS SHALL BE LISTED FOR USE WITH UNGROUNDED SYSTEMS IN COMPLIANCE WITH 2020 NEC 690.4(B) PV WIRE BLACK WIRE MAY BE FIELD-MARKED WHITE IN COMPLIANCE WITH NEC 200.6 (A)(6). PV MODULE CONDUCTORS LOCATED UNDER ARRAYS WILL BE SECURED IN A WORKMANLIKE MANNER IN COMPLIANCE WITH NEC 110.12. WATERPROOFING:* ALL NEW ROOFTOP PENETRATIONS SHALL BE SEALED AND MADE WEATHER TIGHT WITH APPROVED CHEMICAL SEALANT AND FLASHINGS WHERE REQUIRED PER CODE AND GENERAL BUILDING AND ROOFING WORKMANSHIP STANDARDS BY A LICENSED CONTRACTOR. ALL EXTERIOR ELECTRICAL EQUIPMENT, SHALL BE NEMA 3R OR BETTER RATED. ALL EXTERIOR CONDUIT AND CONNECTORS SHALL BE RATED FOR WET LOCATIONS. *ALL NOTES ARE AS APPLICABLE TO THIS PROJECT. DISREGARD ANY NOTES THAT DO NOT APPLY TO THIS PROJECT.N-001Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT RELEASEREVDATE NAME ADDRESSAPN2015 IFC ROOF ACCESS REQUIREMENTS PV SITE LAYOUT LEGEND EXISTING DIMENSIONS ARE APPROX.ONFIRM ALL DIMENSIONS SHOWN PV ARRAY LAYOUTSQUARE FOOTAGE CALCULATIONS ROOF REFERENCE SQUARE FOOTAGE TOTAL PERCENTAGE AZIMUTH AND TILT TABLE SECTION #AZIMUTH ROOF PITCH / TILT EXISTING ROOF ADDRESS kW PHOTOVOLTAIC PLANSSECTION 1 ROOF ACCESS POINT SITE ACCESS GATE ACCESS SECTION 1 PV ARRAY TAGSECTION #MODULE GROUP RA SA GA NOTE: ALL ELECTRICAL LAYOUT DETAILS ON SHEET E-100 NORTH RA RA SECTION 2 SECTION 1 THIS SHEET REPRESENTS THE SOLAR MODULE LAYOUT ON ROOFTOP. SHADED DASHED LINE NEAR PERIMETER OF STRUCTURE EXTERIOR IS AN APPROXIMATE REPRESENTATION OF THE EXTERIOR WALL LOCATION PHOTOVOLTAIC MODULES ARE SCALED IN PLAN VIEW AND MAY NOT BE AN ACCURATELY SCALED REPRESENTATION OF THE ACTUAL SCALE AND GEOMETRY OF THE PHOTOVOLTAIC MODULE. ACTUAL PHOTO- VOLTAIC MODULE DIMENSIONS ARE ON SHEET E-001 FOR THE PURPOSE OF CLARITY, ALL ELECTRICAL LAYOUT DETAILS ARE LOCATED ON SHEET E-100. A. B. C. PV AC DISCONNECT LOCATED ON ACCESSIBLE EXTERIOR WALL WITH EXTERNAL HANDLE VISIBLE, LOCKABLE & LABELED WITHIN 10 FEET OF THE METER SCALE: 1/8” = 1’0” @ SHEET SIZE A3 1408 SECTION-1 290 48.93% 236 40°SECTION-1 236 34°SECTION-2 399SECTION-2 QTY 38 Hanwha Q-cells Q.PEAK DUO-G7 330 MODULES QTY 1 GENERAC PWRcell 7.6 APKE00014 INVERTER PV-100RValley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT SHEET NOTES RELEASEREVDATE NAME ADDRESS* EXISTING ROOF DIMENSIONS ARE APPROX.CONFIRM ALL DIMENSIONS SHOWN PV RACKING LEGEND RACKING LAYOUTRACKING BILL OF MATERIALS (BOM) COMPONENT QTY MODEL LENGTH PV RAIL 1 PV RAIL SPLICE 1 PV RAIL 2 PV RAIL SPLICE 2 RAIL TO ROOFATTACHMENT EXISTING ROOF CONSTRUCTION COMPONENT TYPE ROOF STRUCTURALCONSTRUCTION ROOFING COVERING RACKING MAX PSF ROOF RACKING RAIL SPLICE ROOF RACKING STANCHION W/RETRO FIT FLASHING * DETAILS IN TOP VIEW SECTION 1 PV ARRAY TAGSECTION #MODULE GROUP B. ANCHOR SPACING SHOWNIN DETAIL. UNLESS NOTED OTHERWISE PER RACKINGMANUFACTURER CERTIFIEDENGINEERED PRODUCT ANDLOCAL REQUIREMENTS. SEE"TABLE OF DIMENSIONS" EACH SECTION DETAILED FORHORIZONTAL ANCHOR SPACING. C.SEE SHEET S-200 FOR SPECIFIC RACKING COMPONENTMANUFACTURERS. ADDRESSAPN kW PHOTOVOLTAIC PLANSFRAMING INFO ROOF RACKING RAIL NORTH22'-114"13'-1 12"38'-8"13'-1 12" Rafter-Simple Attic 2"x10"@ 16" MAX OC Rafter-Simple Attic 2"x10"@ 16" MAX OC BACK ROOF MIDDLE ROOF FRONT ROOF Rafter-Simple Attic 2"x6" 24" O.C. SCALE: 1/8” = 1’0” @ SHEET SIZE A3 Rafter-Simple Attic 2"x6"@24" MAX OC & 2"x10"@16"MAX OC Comp Shingle 3.07 PSF QTY 38 Hanwha Q-cells Q.PEAK DUO-G7 330 MODULES QTY 1 GENERAC PWRcell 7.6 APKE00014 INVERTER S-100A. FOR MANUFACTURED PLATED WOOD TRUSSES AT SLOPES OF FLAT TO 10:12, THE HORIZONTAL ANCHOR SPACING SHALL NOT EXCEED 4’-0” AND ANCHORS IN ADJACENT ROWS SHALL BE STAGGERED. UNLESS NOTED OTHERWISE PER RACKING MANUFACTURER CERTIFIED ENGINEERED PRODUCT AND LOCAL REQUIREMENTS.Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT SHEET NOTES RELEASEREVDATE NAME ADDRESSAPNPV RACKING LEGEND 21SCALE: NTS 3 4 A.THESE NOTES APPLY TO RAFTER ROOF CONSTRUCTION. B.THE ROOF STRUCTURE CONFORMED TO BUILDING CODEREQUIREMENTS AT THE TIME IT WAS BUILT. C. STRAND BOARD OR PLYWOOD. 1X SKIP SHEATHING IS ACCEPTABLE. D.THE SOLAR ARRAY DISPLACES ROOF LIVE LOADS (TEMPORARYCONSTRUCTION LOADS) THAT THE ROOF WAS ORIGINALLY DESIGNED TO CARRY. E.IF THE ROOF COVERING IS SHINGLES; IT SHALL BE NO MORETHAN TWO LAYERS. (SHOWN) F.IF ROOF COVERING IS TILE; ITS A SINGLE LAYER. ALL TILES ONPLANE OF PV COMPONENTS ARE SECURE. (NOT SHOWN IN DETAIL) G.THE ROOF STRUCTURE IS STRUCTURALLY SOUND, WITHOUTSIGNS OF ALTERATIONS OR SIGNIFICANT STRUCTURAL DETERIORATION OR SAGGING. H.THE PV MODULES ARE PARALLEL WITH THE ROOF SURFACE. I. AND THE ROOF SURFACE. (SEE TABLE OF DIMENSIONS "H1") J.UPSLOPE ANCHOR SPACING MAY VARY FROM LISTED TABLES. STANCHIONS CAN BE PLACED NO CLOSER THAN 24" O.C. K. # SCALE: NTS SCALE: NTSSCALE: NTS SECTION ELEVATIONSTABLE OF DIMENSIONS DIM COMPONENT DIMENSIONS DIM COMPONENT DIMENSIONS OVERHANG IN THIS AREAOH1 RIDGE BEAM DEPTHR1 ROOF PITCHRISE R2 RAFTER DEPTH THIS AREA PV MODULE HGT. ABOVE ROOFH1 HORIZONTAL SPANHS1 HORIZONTAL SPANHS2 UPSLOPE ANCHOR SPACING RAIL OVERHANGD1 STANCHION O.C.D3 STANCHION O.C.D2 D4 MIN./MAX. STANCHION O.C. TABLE OF COMPONENTS COMPONENT MODEL 1 PV RAIL TYPE 1 2 PV RAIL SPLICE TYPE 1 3 PV RAIL TYPE 2 4 PV RAIL SPLICE TYPE 2 5 STANCHION 6 FLASHING 7 MID CLAMP 8 END CLAMP EXISTING ROOF CONSTRUCTION COMPONENT TYPE MEAN ROOF HGT MAX ROOFING COVERING TABLE OF DIMENSIONS DIM COMPONENT DIMENSIONS DIM COMPONENT DIMENSIONS OVERHANG IN THIS AREAOH1 RIDGE BEAM DEPTHR1 ROOF PITCHRISE R2 RAFTER DEPTH THIS AREA PV MODULE HGT. ABOVE ROOFH1 HORIZONTAL SPANHS1 HORIZONTAL SPANHS2 UPSLOPE ANCHOR SPACING RAIL OVERHANGD1 STANCHION O.C.D3 STANCHION O.C.D2 D4 MIN./MAX. STANCHION O.C. * DETAILS IN SECTION OR SIDE VIEW ROOF RACKING RAIL SPLICE ROOF RACKING STANCHION W/ RETRO FIT FLASHING SECTION 1 PV ARRAY TAGSECTION #MODULE GROUP ADDRESS kW PHOTOVOLTAIC PLANSPER RAIL MANUFACTURER PER RAIL MANUFACTURER PER RAIL MANUFACTURER PER RAIL MANUFACTURER MAX RAFTER SPANMAX RAFTER SPAN L. DETAILS SHOWN ARE A REPRESENTATION OF EXISTING ROOF CONDITIONS. ACTUAL FIELD CONDITIONS MAY VARY. DETAILS ARE SHOWN FOR DIAGRAM USE ONLY. REFER TO TABLES FOR DESIGN CRITERIA. ALL PLUMBING AND ROOF VENTS SHALL NOT BE OBSTRUCTEDBY PV MODULES AND EQUIPMENT. M. ROOF RACKING RAIL * IF BLOCKING REQUIRED32 S-201 1 S-201 HORIZONTAL SPAN 12 RIDGE BEAM FRAMING 1 5 6 7 RISE 3 OH1HS1 PV 1 D3 D2 D1 D2H1R2R1 ** COMP SHINGLE ROOF IN EXAMPLE. SAME ATTACHMENT FOR STANDING SEAM METAL ROOF APPLIES. * IF BLOCKING REQUIRED32 S-201 1 S-201 HORIZONTAL SPAN 12 RIDGE BEAM FRAMING 1 5 6 7 RISE 3 OH1HS1 PV 1 D3 D2 D1 D2H1R2R1 ** COMP SHINGLE ROOF IN EXAMPLE. SAME ATTACHMENT FOR STANDING SEAM METAL ROOF APPLIES. Zilla )ODV L J / Zilla RXEOH tud ZilOD DVH Plate XL LOOD RXEOH WXG / )ODV L J ONLY USED FOR FRONT AND MIDDLE ROOF (E) RAFTER@ 16" O.C. TYPICAL 1'-4"TYP 4'-0"MAX ONLY USED FOR FRONT & MIDDLE ROOF ONLY USED FOR FRONT & MIDDLE ROOF SIMPLE ATTIC / RAFTER - PORTRAIT SIMPLE ATTIC / RAFTER - LANDSCAPE STANCHION DETAIL STANCHION SPACING DETAIL Ultra Rail UR-60 Double Stud XL Integrated 12" 39.8° 3" - 6" TYP 9.85" 19.7" 19.95" 10" 12" 39.8° 3" - 6" TYP 16.58" 33.15" 33.4" 10" 25' Comp Shingle NOT USED S-200Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT SHEET NOTES RELEASEREVDATE NAME ADDRESSAPNPV RACKING LEGEND * DETAILS IN SECTION OR SIDE VIEW 21SCALE: NTS 3 4 SCALE: NTS SCALE: NTSSCALE: NTS ATTACHMENT DETAILSROOF RACKING RAIL SPLICE ROOF RACKING STANCHION W/RETRO FIT FLASHING SECTION 1 PV ARRAY TAGSECTION #MODULE GROUP ADDRESS kW PHOTOVOLTAIC PLANSROOF RACKING RAIL 1/3" OF TOTAL SPAN MAX 2/3" OF TOTAL SPAN MAX RAIL MANUFACTURERRAIL SPLICE KITSEE "S-100 / TABLE OF COMPONENTS" SPACING VARIES STAGGER STANCHIONS WHERE POSSIBLE.SEE SHEET "S-100" FOR:HORIZONTAL ANCHOR SPAN SPACING. (E) FRAMINGTYPICAL * MODULES SHOWN PORTRAIT IN EXAMPLE DCAND/OR 1/3CANT.MAX COMPONENT +2" FROM SIDEOF MODULE 2" ROOF TOPCONDUIT EXTENSION OF RAIL RAIL OR STRUTCONNECTIONS TO MEETWEIGHT REQ. OF EQUIPMENT DCB * MODULES SHOWN PORTRAIT IN EXAMPLE** RAILING SHOWING IN VERTICAL IN EXAMPLE RIDGE BEAM *R2*R1VERIFY THAT NODIAGONAL AND/OR VERTICALATTIC/FRAMING STRUT MEMBERSARE CUT OR NOTCHED * SEE DETAILS "1-2/S200" TABLE OF DIMENSIONS HOLES ALLOWED ONLY IN MIDDLE HALF OF FRAMING SPAN 1/4 1/4 HOLES ALLOWED ONLY IN MIDDLE THIRDOF FRAMING DEPTH, *R2, AND NO LARGERTHAN *R2/4 IN DIAMETER. MINIMUMSPACING BETWEEN HOLES AT *R2 FRAMING SAG IN INCHES NOTTO EXCEED FRAMING LENGTHIN FEET DIVIDED BY 20 NOTCHES DEEPER THAN 1/4"NOT ALLOWED ALONG TOP ORBOTTOM EDGE OF FRAMING NOTE: WHERE FRAMING IS VISIBLE FROM ATTIC &/OR UNDERSIDE OF ROOF,VISUALLY REVIEW FRAMING TO VERIFY THAT NO SIGNIFICANT STRUCTURALDECAY OR UN-REPAIRED FIRE DAMAGE EXISTS. RIDGE SAG IN INCHES NOT TO EXCEED RIDGELENGTH IN FEET DIVIDED BY 20 14" X 1-1/2" LAGS. EIGHT (8) NOS. (E) ROOF SHEATHING /DECKING (E) FRAMING MEMBER L-FOOT PV MODULE, BY OTHERS MODULE END CLAMP SNAPNRACK ULTRA RAIL ZILLA FLASHINGS XL 5/16”-18 X 2-1/4” SS HCS BOLT DOUBLE STUD WASHER INCLUDED ZILLA BASE PLATE XL ONLY USED FOR FRONT AND MIDDLE ROOF 1. (8)1/4 1 ENGINEERING. 2.ADHERE TO RACKING MANUFACTURERS INSTALLATIONINSTRUCTIONS PERTAINING TO CANTILEVER. STANCHION ATTACHMENT DETAIL WITH FLASHING RAIL SPLICE DETAIL - HORIZONTAL RAIL RAIL EXTENSION DETAIL RAFTER HOLE AND CONSTRUCTION DETAIL S-201Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT SHEET NOTES RELEASEREVDATE NAME ADDRESSAPNPV RACKING LEGEND 21SCALE: NTS 3 4 A.THESE NOTES APPLY TO RAFTER ROOF CONSTRUCTION. B.THE ROOF STRUCTURE CONFORMED TO BUILDING CODEREQUIREMENTS AT THE TIME IT WAS BUILT. C. STRAND BOARD OR PLYWOOD. 1X SKIP SHEATHING IS ACCEPTABLE. D.THE SOLAR ARRAY DISPLACES ROOF LIVE LOADS (TEMPORARYCONSTRUCTION LOADS) THAT THE ROOF WAS ORIGINALLY DESIGNED TO CARRY. E.IF THE ROOF COVERING IS SHINGLES; IT SHALL BE NO MORETHAN TWO LAYERS. (SHOWN) F.IF ROOF COVERING IS TILE; ITS A SINGLE LAYER. ALL TILES ONPLANE OF PV COMPONENTS ARE SECURE. (NOT SHOWN IN DETAIL) G.THE ROOF STRUCTURE IS STRUCTURALLY SOUND, WITHOUTSIGNS OF ALTERATIONS OR SIGNIFICANT STRUCTURAL DETERIORATION OR SAGGING. H.THE PV MODULES ARE PARALLEL WITH THE ROOF SURFACE. I. AND THE ROOF SURFACE. (SEE TABLE OF DIMENSIONS "H1") J.UPSLOPE ANCHOR SPACING MAY VARY FROM LISTED TABLES. STANCHIONS CAN BE PLACED NO CLOSER THAN 24" O.C. K. # SCALE: NTS SCALE: NTSSCALE: NTS SECTION ELEVATIONSTABLE OF DIMENSIONS DIM COMPONENT DIMENSIONS DIM COMPONENT DIMENSIONS OVERHANG IN THIS AREAOH1 RIDGE BEAM DEPTHR1 ROOF PITCHRISE R2 RAFTER DEPTH THIS AREA PV MODULE HGT. ABOVE ROOFH1 HORIZONTAL SPANHS1 HORIZONTAL SPANHS2 UPSLOPE ANCHOR SPACING RAIL OVERHANGD1 STANCHION O.C.D3 STANCHION O.C.D2 D4 MIN./MAX. STANCHION O.C. TABLE OF COMPONENTS COMPONENT MODEL 1 PV RAIL TYPE 1 2 PV RAIL SPLICE TYPE 1 3 PV RAIL TYPE 2 4 PV RAIL SPLICE TYPE 2 5 STANCHION 6 FLASHING 7 MID CLAMP 8 END CLAMP EXISTING ROOF CONSTRUCTION COMPONENT TYPE MEAN ROOF HGT MAX ROOFING COVERING TABLE OF DIMENSIONS DIM COMPONENT DIMENSIONS DIM COMPONENT DIMENSIONS OVERHANG IN THIS AREAOH1 RIDGE BEAM DEPTHR1 ROOF PITCHRISE R2 RAFTER DEPTH THIS AREA PV MODULE HGT. ABOVE ROOFH1 HORIZONTAL SPANHS1 HORIZONTAL SPANHS2 UPSLOPE ANCHOR SPACING RAIL OVERHANGD1 STANCHION O.C.D3 STANCHION O.C.D2 D4 MIN./MAX. STANCHION O.C. * DETAILS IN SECTION OR SIDE VIEW ROOF RACKING RAIL SPLICE ROOF RACKING STANCHION W/ RETRO FIT FLASHING SECTION 1 PV ARRAY TAGSECTION #MODULE GROUP ADDRESS kW PHOTOVOLTAIC PLANSPER RAIL MANUFACTURER PER RAIL MANUFACTURER PER RAIL MANUFACTURER PER RAIL MANUFACTURER MAX RAFTER SPANMAX RAFTER SPAN L. DETAILS SHOWN ARE A REPRESENTATION OF EXISTING ROOF CONDITIONS. ACTUAL FIELD CONDITIONS MAY VARY. DETAILS ARE SHOWN FOR DIAGRAM USE ONLY. REFER TO TABLES FOR DESIGN CRITERIA. ALL PLUMBING AND ROOF VENTS SHALL NOT BE OBSTRUCTEDBY PV MODULES AND EQUIPMENT. M. ROOF RACKING RAIL * IF BLOCKING REQUIRED32 S-201 1 S-201 HORIZONTAL SPAN 12 RIDGE BEAM FRAMING 1 5 6 7 RISE 3 OH1HS1 PV 1 D3 D2 D1 D2H1R2R1 ** COMP SHINGLE ROOF IN EXAMPLE. SAME ATTACHMENT FOR STANDING SEAM METAL ROOF APPLIES. * IF BLOCKING REQUIRED32 S-201 1 S-201 HORIZONTAL SPAN 12 RIDGE BEAM FRAMING 1 5 6 7 RISE 3 OH1HS1 PV 1 D3 D2 D1 D2H1R2R1 ** COMP SHINGLE ROOF IN EXAMPLE. SAME ATTACHMENT FOR STANDING SEAM METAL ROOF APPLIES. (E) FRAMING@ 24" O.C. TYPICAL 2'-0"TYP.4'-0"MAX PARTS LIST DESCRIPTIONPART NUMBERQTYITEM SNAPNRACK, UMBRELLA LAG, TYPE 3, 4IN, SS242-9226611 SNAPNRACK, ULTRA FOOT FOR U FLASHING, SILVER / BLACK242-01219, 242-0122012 SNAPNRACK, COMP FLASHING, 9IN X 12IN, SILVER / BLACK ALUM232-01375, 232-0137613 3 1 2 2 ONLY USED FOR BACK ROOF ONLY USED FOR BACK ROOF ONLY USED FOR BACK ROOF SIMPLE ATTIC / RAFTER - PORTRAIT SIMPLE ATTIC / RAFTER - LANDSCAPE STANCHION DETAIL STANCHION SPACING DETAIL Ultra Rail UR-60 242-01220 L Foot Integrated 12" 39.8° 3" - 6" TYP 9.85" 19.7" 19.95" 6" 12" 39.8° 3" - 6" TYP 16.58" 33.15" 33.4" 6" 25' Comp Shingle NOT USED S-202Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT SHEET NOTES RELEASEREVDATE NAME ADDRESSAPNPV RACKING LEGEND * DETAILS IN SECTION OR SIDE VIEW 1. (1) ENGINEERING. 2.ADHERE TO RACKING MANUFACTURERS INSTALLATION INSTRUCTIONS PERTAINING TO CANTILEVER. 21SCALE: NTS 3 4 SCALE: NTS SCALE: NTSSCALE: NTS ATTACHMENT DETAILSROOF RACKING RAIL SPLICE ROOF RACKING STANCHION W/RETRO FIT FLASHING SECTION 1 PV ARRAY TAGSECTION #MODULE GROUP ADDRESS kW PHOTOVOLTAIC PLANSROOF RACKING RAIL 1/3" OF TOTAL SPAN MAX 2/3" OF TOTAL SPAN MAX RAIL MANUFACTURERRAIL SPLICE KITSEE "S-100 / TABLE OF COMPONENTS" SPACING VARIES STAGGER STANCHIONS WHERE POSSIBLE.SEE SHEET "S-100" FOR:HORIZONTAL ANCHOR SPAN SPACING. (E) FRAMINGTYPICAL * MODULES SHOWN PORTRAIT IN EXAMPLE DCAND/OR 1/3CANT.MAX COMPONENT +2" FROM SIDEOF MODULE 2" ROOF TOPCONDUIT EXTENSION OF RAIL RAIL OR STRUTCONNECTIONS TO MEETWEIGHT REQ. OF EQUIPMENT DCB * MODULES SHOWN PORTRAIT IN EXAMPLE** RAILING SHOWING IN VERTICAL IN EXAMPLE RIDGE BEAM *R2*R1VERIFY THAT NODIAGONAL AND/OR VERTICALATTIC/FRAMING STRUT MEMBERSARE CUT OR NOTCHED * SEE DETAILS "1-2/S200" TABLE OF DIMENSIONS HOLES ALLOWED ONLY IN MIDDLE HALF OF FRAMING SPAN 1/4 1/4 HOLES ALLOWED ONLY IN MIDDLE THIRDOF FRAMING DEPTH, *R2, AND NO LARGERTHAN *R2/4 IN DIAMETER. MINIMUMSPACING BETWEEN HOLES AT *R2 FRAMING SAG IN INCHES NOTTO EXCEED FRAMING LENGTHIN FEET DIVIDED BY 20 NOTCHES DEEPER THAN 1/4"NOT ALLOWED ALONG TOP ORBOTTOM EDGE OF FRAMING NOTE: WHERE FRAMING IS VISIBLE FROM ATTIC &/OR UNDERSIDE OF ROOF,VISUALLY REVIEW FRAMING TO VERIFY THAT NO SIGNIFICANT STRUCTURALDECAY OR UN-REPAIRED FIRE DAMAGE EXISTS. RIDGE SAG IN INCHES NOT TO EXCEED RIDGELENGTH IN FEET DIVIDED BY 20 ALL ANCHOR LAGS TO BE MINIMUM 2-1/2" EMBEDMENT INTO FRAMING MEMBERS (E) ROOF SHEATHING /DECKING (E) FRAMING MEMBER L-FOOT PV MODULE, BY OTHERS MODULE END CLAMP SNAPNRACK ULTRA RAIL SNAPNRACK COMP UMBRELLA FLASHINGS5/16”-18 X 2-1/4” SS HCS BOLT ONLY USED FOR BACK ROOF STANCHION ATTACHMENT DETAIL WITH FLASHING RAIL SPLICE DETAIL - HORIZONTAL RAIL RAIL EXTENSION DETAIL RAFTER HOLE AND CONSTRUCTION DETAIL S-204Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT RELEASEREVDATE NAME ADDRESSAPNPV SYSTEM MAXIMUM VOLTAGE (MODULE VocMAX) DATA SOURCE SOLARABCS.ORG/ABOUT/PUBLICATIONS/REPORTS/ EXPEDITED-PERMIT/MAP/ EXTREME MIN. STCTEMPERATURE CORRECTEDTEMPERATURE MFR. PMAX TEMPCOEFFICIENT[-0.#%/C] * 100 FORMULA CORRECTEDTEMP.COEFFICIENT MODULE Voc[VDC] TEMPERATURECORRECTEDOPEN CIRCUITVOLTAGE - =*= +*=EQUIP. CALCULATIONSPV MODULE #1 SPECIFICATIONS MANUFACTURER MODEL NUMBER WEIGHT Ibs DIMENSIONS L" x W" x D"/ PEAK POWER @ STC (Pmax)WATTS Voc (OPEN-CIRCUIT VOLTAGE)VOLTS DC Vmp (MAX-POWER VOLTAGE)VOLTS DC isc (SHORT-CIRCUIT CURRENT)AMPS imp (OPERATING CURRENT)AMPS MFR. Voc TEMP COEFFICIENT %/K MAX SERIES FUSE RATING AMPS TEMP. CORRECTED Voc VOLTS DC DC/DC OPTIMIZER (IF APPL.) MANUFACTURER MODEL NUMBER WEIGHT Ibs RATED OUTPUT isc AMPS MAX OUTPUT VOLTAGE VOLTS MAX INPUT VOLTAGE Voc VOLTS DC COMBINER / DISCONNECT #1 MANUFACTURER MODEL NUMBER OCPD (DISCONNECT TYPE) WEIGHT Ibs NEMA RATING LOCATION OF COMPONENTDC INPUT SERIES FUSE RATING FOR PV MODULES AMPS (OCPD) QUANTITY OF PV SOURCE CIRCUITS QTY MAX PV MODULE Voc VOLTS DC MAX # OF MODULES IN CIRCUIT QTY MAX ALLOWED INPUT VOLTAGE VOLTS DC MAX INPUT FUSE/BREAKER RATING AMPSDC OUTPUT MAX CIRCUIT OUTPUT CURRENT AMPS MAX CONT. OUTPUT CURRENT AMPS STRING INVERTER #1 SPECIFICATIONS MANUFACTURER MODEL NUMBER NOMINAL POWER RATING WATT AC WEIGHT Ibs.DC INPUT Max INPUT DC VOLTAGE VOLTS DC Min. MPPT VOLTAGE RANGE VOLTS DC Max. MPPT VOLTAGE RANGE VOLTS DC Max INPUT CURRENT AMPS MPPT QTY INTEGRATED DC DISCONNECT COMPLY W/NEC 690.17INTEGRATED AC DISCONNECTAC OUTPUT NOMINAL VOLTAGE OUTPUT VOLTS AC MAX OVERCURRENT PROTECTION (OCPD)AMPS MAX. OUTPUT CURRENT AMPS - MAX AC SUB-PANEL #1 (IF APPL.) NEW OR EXISTING MAKE / MODEL TYPE OF PANEL NUMBER OF POLES P NEMA RATING BUSS BAR RATING AMPS SUB-PANEL MAIN BREAKER AMPS MAIN SERVICE PANEL P.O.C. BREAKER AMPS AMPS MAX ALLOWABLE SOLAR CURRENT AMPS PV BACKFEED BREAKER #1 AMPS (Imax) AMPS (Imax) MAIN SERVICE PANEL (IF APPL.) NEW OR EXISTING ELECTRICAL SERVICE BUSS BAR RATED CURRENT AMPS MAIN BREAKER RATED CURRENT AMPS AMPS AMPS AMPS (Imax) AMPS (Imax) ADDRESSTHICK WATTSMAX. AC APPARENT POWER kW PHOTOVOLTAIC PLANSDC COMBINER / DISCONNECT #2 (IF APPL.) MANUFACTURER MODEL NUMBER OCPD (DISCONNECT TYPE) WEIGHT Ibs NEMA RATING LOCATION OF COMPONENTDC INPUT SERIES FUSE RATING FOR PV MODULES AMPS (OCPD) QUANTITY OF PV SOURCE CIRCUITS QTY MAX PV MODULE Voc VOLTS DC MAX # OF MODULES IN CIRCUIT QTY MAX ALLOWED INPUT VOLTAGE VOLTS DC MAX INPUT FUSE/BREAKER RATING AMPSDC OUTPUT MAX CIRCUIT OUTPUT CURRENT AMPS MAX CONT. OUTPUT CURRENT AMPS AMPS MANUFACTURER MODEL NUMBER OCPD (DISCONNECT TYPE) WEIGHT Ibs NEMA RATING LOCATION OF COMPONENTDC INPUT QTY MAX PV MODULE Voc MAX # OF MODULES IN CIRCUIT QTY MAX ALLOWED INPUT VOLTAGE AMPSDC OUTPUT MAX CIRCUIT OUTPUT CURRENT AMPS MAX CONT. OUTPUT CURRENT SERIES FUSE RATING FOR PV MODULES AMPS (OCPD) QUANTITY OF PV SOURCE CIRCUITS VOLTS DC VOLTS DC MAX INPUT FUSE/BREAKER RATING DC COMBINER / DISCONNECT #3 (IF APPL.) QUANTITY STRING INVERTER #2 SPECIFICATIONS (IF APPL.) AMPS - MAX MANUFACTURER MODEL NUMBER NOMINAL POWER RATING WATT AC WEIGHT Ibs.DC INPUT Max INPUT DC VOLTAGE VOLTS DC Min. MPPT VOLTAGE RANGE VOLTS DC Max. MPPT VOLTAGE RANGE VOLTS DC Max INPUT CURRENT AMPS MPPT QTY INTEGRATED DC DISCONNECT COMPLY W/NEC 690.17INTEGRATED AC DISCONNECTAC OUTPUT NOMINAL VOLTAGE OUTPUT VOLTS AC MAX OVERCURRENT PROTECTION (OCPD)AMPS MAX. OUTPUT CURRENT WATTSMAX. AC APPARENT POWER QUANTITY INVERTER(S) INVERTER(S) AC COMBINER #1 (SOLAR LOAD CENTER) MANUFACTURER MODEL NUMBER RATED OPERATIONAL VOLTAGE VOLTS RATED CURRENT AMPS NUMBER OF POLES P NEMA RATING MAIN BREAKER SIZE TOTAL INPUT CURRENT AMPS NUMBER OF BRANCH CIRCUITS AMPS CIRCUITS AC DISCONNECT #1 MANUFACTURER (IF APPL.) AMPS MODEL NUMBER DISCONNECT DEVICE TYPE RATED OPERATIONAL VOLTAGE VOLTS RATED CURRENT AMPS NUMBER OF POLES P NEMA RATING FUSE RATING AMPS TOTAL INPUT CURRENT QUANTITY AC DISCO.(S) AC DISCONNECT #2 MANUFACTURER (IF APPL.) AMPS MODEL NUMBER DISCONNECT DEVICE TYPE RATED OPERATIONAL VOLTAGE VOLTS RATED CURRENT AMPS NUMBER OF POLES P NEMA RATING FUSE RATING AMPS TOTAL INPUT CURRENT QUANTITY AC DISCO.(S) PV BACKFEED BREAKER #2 PV BACKFEED BREAKER #3 PV BACKFEED BREAKER #4 AMPS (Imax) AMPS (Imax) AC COMBINER #2 (SOLAR LOAD CENTER) MANUFACTURER MODEL NUMBER RATED OPERATIONAL VOLTAGE VOLTS RATED CURRENT AMPS NUMBER OF POLES P NEMA RATING MAIN BREAKER SIZE TOTAL INPUT CURRENT AMPS NUMBER OF BRANCH CIRCUITS AMPS CIRCUITS AMPS (Imax) AMPS (Imax) AMPS (Imax) SUM OF EXISTING CIRCUIT BREAKERS AMPS (Imax) MAX ALLOWABLE SOLAR CURRENT 100% MAX ALLOWABLE SOLAR CURRENT 120% PV BACKFEED BREAKER #1 PV BACKFEED BREAKER #2 PV BACKFEED BREAKER #3 PV BACKFEED BREAKER #4 ALT. ENERGY BACKFEED BREAKER (IF APPL.) SUM OF EXISTING CIRCUIT BREAKERS BATTERY #1 SPECIFICATIONS Years/MWh 10/7.56 Modules ion - Warranty: Li Years 10 : ElectronicsWarranty UL9540, UL1973, UL1642CSA - 22.2Compliance - ™Ebus DC NanogridR Communication Protocol (kg)b,l (202) 445, eight (Installed)W (kg)b,l (52) 15,1 eight (Enclosure)W (kg)b,l 55, (25) ion module) - Weight (Li VDC 46.8 Module Voltage - 6 Battery Modules (mm)n,I x 22 x 10(1725 x 560 x 235) 68 Dimensions mt,f (3000) 9834, Maximum Installation Altitude C)ᵒF, (ᵒ )30 - 86, (13 - 54 Recommended Temp. Range C)ᵒ, (Fᵒ45)-(5 113,-41 ngeOperating Temp. Ra % 96.5 Trip Efficiency-Round VDC 420-360 Ebus Voltage: Input/OutputR kW 10 utesPower: 2 min kW 8.4 Power: 60 minutes kW 6.7 Power: Rated Continuous kWh 17.1 Usable Energy sUnitSpecification - Hanwha Q-cells EatonDG222URB1Q.PEAK DUO-G7 33039.466.3 x 39.4 x 1.26 NON-FUSIBLE DISCONNECT120/24033040.6234.1410.15 60 45.49 9.67 3R2 N/A32-0.2720.0 GeneracPV Link APKE000107.38420420 GENERACPWRcell 7.6 APKE00014 760062.7 420360420202 YESNO 24076004032 -20 25 -45 -0.27%0.12 1 1.12 40.62 45.49 1 E-001NEW120/240V Single Phase 225 200 25 70 40 Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT RELEASEREVDATE NAME ADDRESSDC WIRE AND CONDUIT SIZING CHART [SEE SHEET E-003 FOR THREE LINE DIAGRAM] TAG CIRCUITORIGIN CIRCUIT CONDUCTORSPECIFICATIONS REQUIRED CONDUCTOR AMPACITY CONDUCTOR TEMPERATURE DERATING CONDUIT FILLDERATING CORRECTED AMPACITY CALCULATION AMPACITY CHECK TEMPRATING TRADESIZE AMPACITY PER 310.16 MAXCURRENT690.8 (A)(1) CONT.OPERATION690.8 (B)(1) REQUIREDAMPACITY CIRCUITENVIRONMENT AMBIENTTEMP. HGT.ABOVEROOF (in) TEMP.ADDER PER310.15(B)(2)(c) OPERAT.TEMP. AMPACITYCORRECTION310.15(B)(2)(a) # OFUNGRND.COND. AMPACITYCORRECTION310.15(B)(3)(a) COND.AMPACITY TEMP.DERATING CONDUITFILLDERATING X X X = X X =CORRECTEDAMPACITY REQUIREDAMPACITY <CORRECTEDAMPACITY DC1 X X X = X X =< DC2 X X X = X X =< DC3 X X X = X X =< DC4 X X X = X X =< DC5 X X X = X X =< AC WIRE AND CONDUIT SIZING CHART [SEE SHEET E-003 FOR THREE LINE DIAGRAM] TAG CIRCUIT ORIGIN CIRCUITDESTINATION CONDUCTORSPECIFICATIONS REQUIRED CONDUCTORAMPACITY CONDUCTOR TEMPERATURE DERATING CONDUIT FILLDERATING CORRECTED AMPACITY CALCULATION AMPACITY CHECK TEMPRATING TRADESIZE AMPACITY PER 310.16 CONT.OPERATION690.8 (B)(1)X =REQUIREDAMPACITY CIRCUITENVIRONMENT AMBIENTTEMP. HGT.ABOVEROOF (in) TEMP.ADDER PER310.15(B)(2)(c) OPERAT. AMPACITYCORRECTION310.15(B)(2)(a) # OFUNGRND.COND. AMPACITYCORRECTION310.15(B)(3)(a) COND.AMPACITY X TEMP.DERATING X CONDUITFILLDERATING =CORRECTEDAMPACITY REQUIREDAMPACITY <CORRECTEDAMPACITY AC1 X =X X =< AC2 X =X X =< AC3 X =X X =< AC4 X =X X =< AC5 X =X X =WIRE AND COND. CALCS.1. ANY CONDUCTOR LENGTH UNDER 50' DOESN'T REQUIRE VOLTAGE DROP CALCULATIONS DEEMED QUESTIONABLE TO PREVENT ISSUES RELATED TO USING CONDUCTORS THAT ARE IMPROPERLY SIZED.3.4.CEC/NEC 310.15(A)(2) (AS APPLICABLE) WHERE TWO DIFFERENT AMPACITIES APPLY TO ADJACENT PORTIONS OF A CIRCUIT, THE HIGHER AMPACITY SHALL BE PERMITTED TO BEUSED BEYOND THE POINT OF TRANSITION, A DISTANCE EQUAL TO 10'-0" (3 METERS) OR 10% OF THE CIRCUIT LENGTH FIGURED AT THE HIGHER AMPACITY, WHICHEVER IS LESS. WHEN LESS THAN 10'-0" OR 10% OF THE CIRCUIT LENGTH; THE LESSER AMPACITY MAY BE USED. WIRE COLOR CODING (2020) CEC/NEC SECTIONS 250.119 & 200.6 PV DC WIRING AC WIRING 2.BECAUSE WE ARE UNABLE TO DETERMINE THE EXACT PATH THE INSTALLER WILL RUN CONDUCTORS; WORST CASE SCENARIOS, ROUNDING UP SIZES OF CONDUCTORS THAT ARE EQUIPMENT GROUND GREEN OR BARE, OR GREEN/YELLOW EQUIPMENT GROUND GREEN OR BARE, OR GREEN/YELLOW TYPICALLY NEGATIVE WHITE OR GRAY (NEUTRAL)WIRING METHODS IN THESE CALCULATIONS DON'T EXCEED 1000 VOLTS GROUNDED CONDUCTOR. GROUNDED CONDUCTOR WHITE OR GRAY UNGROUNDED CONDUCTOR(S).TYPICALLY POSITIVE ANY COLOR OTHER THAN GREEN OR WHITE/GRAY UNGROUNDED L1 AND L2 ANY COLOR OTHER THAN GREEN OR WHITE/GRAY ALLOWED. CONVENTION IS RED FOR GROUNDED SYSTEMS CONDUCTOR(S) HOT: CONVENTION IS L1 BLACK RED (+) AND BLACK (-) FOR UNGROUNDED SYSTEMS CONVENTION IS L2 RED WIRE AND CONDUCTOR NOTES APN ADDRESS kW PHOTOVOLTAIC PLANSAC6 X =X X =< AC7 X =X X =< AC8 X =X X =< AC9 X =X X =< AC10 X =X X = < < DC6 X X X = X X =< DC7 X X X = X X =< DC8 X X X = X X =< #OFCOMBINEDPARALLELSTRINGS DESTINATION QTY INPARALLEL &MATERIAL QTY INPARALLEL &MATERIAL lsc (AMPS)ORCOMPONENT(AMPS) MAX INV. OUTPUTCURRENT (AMPS)ORCOMPONENT(AMPS) PV MODULE DC/DC CONVERTER (1) CU 90 #12 AWG 30 10.15 1 1.25 1.25 15.86 ROOFTOP 33 0.5" – 3.5"22 55 0.71 2 N/A 30 0.76 1.0 22.8 15.86 22.8 PV LINK Y-CONNECTOR (1) CU 90 #10 AWG 40 8 1 1 1.25 10 ROOFTOP 33 0.5" – 3.5"22 55 0.71 10 N/A 40 0.76 1.0 30.4 10 30.4 Y-CONNECTOR JUNCTION BOX (1) CU 90 #10 AWG 40 8 3 1 1.25 30 ROOFTOP 33 0.5" – 3.5"22 55 0.71 4 N/A 40 0.76 1.0 30.4 30 30.4 JUNCTION BOX INVERTER (1) CU 90 #10 AWG 40 24.0 1 1 1.25 30 ATTIC 33 IN ATTIC 0 33 0.96 4 0.80 40 0.96 0.80 30.72 30 30.72 BATTERY INVERTER (1) CU 90 #10 AWG 40 27.77 1 1 1.25 34.71 INT/EXT WALL 33 N/A 0 33 0.96 2 1.0 40 0.96 1.0 38.4 34.71 38.4 47.0 0.94 0.94 0.94 0 0 0 N/A N/A N/A N/A 0 0.94 40.0 50.0 47.0 61.1 1.0 1.0 0.94 0.94651.033535EXT WALL50.050 (1) CUAUTO TRANSFER SWITCH EXT WALL INVERTER AC DISCONNECT (1) CU 75 #8 AWG 50 1.25 32 40.0 EXT WALL 35 35 3 1.0 50 0.94 1.0 47.0 40.0 AC DISCONNECT PRODUCTION METER (1) CU 75 #8 AWG 50 1.25 32 40.0 EXT WALL 35 N/A 0 35 0.94 3 1.0 50 0.94 1.0 47.0 40.0 47.0 PRODUCTION METER EXISTING SERVICE PANEL (1) CU 75 #8 AWG 50 1.25 32 40.0 EXT WALL 35 35 3 1.0 50 47.0 INVERTER AUTO TRANSFER SWITCH (1) CU 75 #6 AWG 65 N/A 61.1 CRITICAL LOAD PANEL 75 #6 AWG 65 N/A 50 50.0 35 35 3 1.0 65 0.94 1.0 61.1 50.0 E-00261.1 Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMITAUTO TRANSFER SWITCH EXISTING SERVICE PANEL (1) CU 75 #6 AWG 65 N/A 50 50.0 EXT WALL 35 N/A 0 35 0.94 3 1.0 65 0.94 1.0 61.1 50.0 61.1 AC4 3 LEGEND RELEASEREVDATE NAME ADDRESSTHREE LINE DIAGRAMEQUIPMENT TABLE QTY COMPONENT 1 PV MODULES 2 DC DISCONNECT3 4 JUNCTION BOX5 RAPID SHUTDOWN6 7 AC/DC INVERTER 8 AC/DC INVERTER W/ INTE AC DISC 9 10 AUTO TRANSFER SWITCH 11 PROD/GEN METER 12 CRITICAL LOAD PANEL 13 14 15 EXISTING UTILITY METER NOTE: EQUIP TAGS MAY NOT BE IN SEQUENTIAL ORDER, N/A USED TAG APN ADDRESSSEE SHEET E-001 FOR ADDITIONAL ELECTRICAL SPECIFICATIONS kW PHOTOVOLTAIC PLANSELECTRICAL NOTES DC CONDUCTOR TAG AC CONDUCTOR TAG EQUIPMENT TAG AC# DC# GROUND CONDUCTOR TAGGND STRING MODULE QTY INVERTER # BACK-FEED SOLAR BREAKER: CONDUCTOR TABLE TAG QTY*SIZE TYPE DC1 DC2 DC3 DC4 DC5 AC1 AC2 AC3 AC4 AC5 GROUND SIZE TYPE CONDUIT TABLE AC6 AC7 AC8 AC9 AC10 DC6 DC7 DC8 16 AC DISCONNECT (INDEPENDENT) • * INCLUDES GROUND & CURRENT CARRYING CONDUCTORS BATTERY DC MODULE LEVEL RSD UNGROUNDED PV SYSTEMS: •INVERTERS, MODULES, AND DC COMPONENTS MUST BE LISTEDFOR USE IN UNGROUNDED SYSTEMS, TYPICALLY TRANSFORMER-LESS (TL) •OCPD'S WHERE NECESSARY MUST HAVE DISCONNECTING MEANS. •PV SOURCE CIRCUITS MUST BE EITHER PV WIRE AND LISTED FOR WET LOCATIONS OR JACKETED MULTI-CONDUCTOR CABLESINSTALLED IN RACEWAY.•THE AC SIDE IS STILL GROUNDED ON THE NEUTRAL CONDUCTOR. •REQUIRE EQUIPMENT GROUNDING BUT DOES NOT HAVE SYSTEMGROUNDING; NO DC CURRENT-CARRYING CONDUCTOR ISCONNECTED TO GROUND. THESE CONDUCTORS ARE COLORCODED DIFFERENTLY THAN GROUNDED PV SYSTEMS. AC/DC ELECTRICAL NOTES: •ALL OVERCURRENT PROTECTION DEVICES (OCPDs) MUST BERATED FOR 600 VOLTS ON THE DC / PV POWER SIDEOF THE INVERTER. •EXTERIOR ENCLOSURES TO BE NEMA TYPE 3R OR BETTER. •ALL CONDUIT AND CONDUIT CONNECTIONS SHALL BE RATED FOR WET AND DAMP LOCATIONS WHEN APPLICABLE. INTERCONNECTION NOTES:705.12(B)(4) CIRCUIT BREAKERS MUST BE SUITABLE FORBACKFEEDING. NEC INFORMATIONAL NOTE: FUSED DISCONNECTS, UNLESS OTHERWISE MARKED,ARE SUITABLE FOR BACKFEEDING. 690.13(F)(2) DEVICES MARKED WITH "LINE” AND “LOAD” SHALLNOT BE PERMITTED FOR BACKFEED OR REVERSE CURRENT 705.12(B)(5) CIRCUIT BREAKERS BACK FEED FROM UTILITYINTERACTIVE INVERTERS (ANTI-ISLANDING, UL 1741 CERTIFIED) • • •1 1 1 1 1 1 1 1 1 1 EGC M 16 G N BUSRATING225A 14 MAIN C/BRATING200A AC1 AC GEC G AC G N G L2 L1 3 6 DC GNL2L1 GNL2L1 N G L2 L1 PWRCell - + DC5 INVERTER NAMEPLATE RATING 7600W /240V DC1 DC1 DC1 DC1 DC1 G G EGC DC3 DC4 5 8 MODULES 7 MODULES 7 MODULES 8 MODULES 8 MODULES MODULE NAMEPLATERATING 330WMC-4Y-CONNECTORS 7 N G L2 L1PV N G L2 L1 11 AC2 AUTOTRANSFERSWITCH L1 L2 N L1 L2 N G L1L2NG 10 G N G 50ADC2 AC5 AC6 50A 12 R3METER NEMA LOCATED EXTERIOR ON WALL NEAR V 240A 60APPROACH TO RESIDENCE SYSTEM DISCONNECT VISIBLE FROM READILY ACCESSIBLE OPEN BLADE AC LOCATED EXTERIOR SOLAR GENERATION (LOAD) BOTTOM LUGS TO TOP LUGS TO UTILITY (LINE) MA SMART GENERATION METER 4 4 4 4 4 4 4 4 4 4 2 2 2 2 2 40AL2 L1 L2 L1 GG NN 9 SERVICE TO BE UPGRADED TO 200A THE BATTERY WILL ONLY BE CHARGED BY PV.THE BATTERY WILL DISCHARGE TO ON SITE LOADS. THE BATTERY DISCHARGE TO THE GRID ONLY IF REQUESTED BY THE GRID VIA CONNECTED SOLUTIONS. 13 RSD SWITCHEMERGENCY EMERGENCY BATTERYDISCONNECT 38 Hanwha Q-cells Q.PEAK DUO-G7 330 5 PV Link APKE00010 N/A INTEGRATED IN INV 38 SnapRS Device 2 Generic NEMA 4 JUNCTION BOX N/A INTEGRATED IN INV & OPT 1 GENERAC PWRcell 7.6 APKE00014 0 1 8 Eaton DG222URB INV 1 RSXW200A3 2 8 INV 1 3 7 INV 1 4 7 INV 1 1 1 1 1 1 5 8 INV 1 0 1 120/240V - 1 40 A 2 #12 AWG PV Wire #6 AWG N/A Open Air 11 #10 AWG PV Wire #6 AWG N/A Open Air 1 5 #10 AWG PV Wire #6 AWG N/A Open Air NEW MAIN SERVICE PANEL 225A BUS/200A MB 5 #10 AWG THWN-2 #8 AWG 3/4 inch EMT EXISTING MAIN SERVICE PANEL 2 #10 AWG THWN-2 #8 AWG 3/4 inch EMT Generac PWRcell 17 Battery 4 #8 AWG THWN-2 #8 AWG 3/4 inch EMT 4 #8 AWG THWN-2 #8 AWG 3/4 inch EMT 4 #8 AWG THWN-2 #8 AWG 3/4 inch EMT 4 #6 AWG THWN-2 #8 AWG 3/4 inch EMT 4 #6 AWG THWN-2 #8 AWG 3/4 inch EMT NO CENTER-FED MAIN BREAKER. PANEL CONFIGURED PER CEC/NEC 705.12(B)(2)(3)(b)E-003DC/DC OPTIMIZER Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT4 #6 AWG THWN-2 #8 AWG 3/4 inch EMT NATIONAL SMART GEN METER 100 A BUS/ LUG ONLY RELEASEREVDATE NAME ADDRESSAPNELECTRICAL SYMBOL LEGEND AC DISCONNECT DC DISCONNECT DC COMBINER BOX AUTO TRANSFER SWITCHCB DC AC ATS ELECTRICAL LAYOUTEQUIPMENT GROUNDING 1. METAL PV MODULE FRAMES MUST BE CONNECTED TO THE EGC(EQUIPMENT GROUNDING CONDUCTOR). 1.1. WEEBS MAY BE USED IN LIEU OF MODULE GROUND CLAMPSOR LUGS, WITH APPROVAL OF AHJ AND RACKING MFG. WEEBSARE ONE TIME USE ONLY. SEE "we-llc.com" FOR RACKINGSPECIFIC WEEB, INSTALL INSTRUCTIONS, AND UL 2703 CERT. 1.2. FOR "LAY-IN" LUG MODULE GROUNDING; CORRECTHARDWARE OF PROPER METAL MATERIAL TO AVOIDCORROSION MUST BE USED. TYPICALLY DIRECT BURIAL RATED,TINNED, OR STAINLESS STEEL. GROUNDING LUGS MUST BEATTACHED AT MARKED LOCATION ON EACH MODULE. 2. THE EGC (EQUIPMENT GROUNDING CONDUCTOR) IS USED TOBOND ALL NON-CURRENT CARRYING CONDUCTORS AND EXPOSEDMETAL PARTS THAT MIGHT COME INTO CONTACT WITHCURRENT-CARRYING CONDUCTORS, INCLUDING THE FOLLOWING: 2.1. PV MODULES FRAMES, ARRAY MOUNTING RACKING; THEMETAL CHASSIS OF EQUIPMENT SUCH AS INVERTERS,DISCONNECTS, METERS, JUNCTION BOXES AND COMBINERBOXES; AND METAL CONDUIT HOLDING CIRCUITS > 250 VOLTSTO GROUND PER NEC 250.97 3. THE GEC (GROUNDING ELECTRODE CONDUCTOR) IS THECONDUCTOR USED TO CONNECT THE GE OR GE SYSTEM TO THESYSTEM GC, TO THE EGC, OR TO BOTH. 4. THE GE (GROUNDING ELECTRODE) IS A CONDUCTING OBJECT,OFTEN A ROD, RING, OR PLATE ESTABLISHING A DIRECTCONNECTION TO EARTH. THE AC SYSTEM GROUND IS EXISTING,USUALLY AT THE EXISTING MAIN PANEL AND/OR UTILITY METER.THE GROUND CAN ONLY OCCUR IN ONE PLACE AND MUST NOT BEDUPLICATED IN SUB-PANELS OR ANYWHERE ELSE ON AC SIDE. SERVICE PANELSP ADDRESS kW PHOTOVOLTAIC PLANSSOLAR LOAD CENTER BATTERY SLC AC COMBINERACC BATTINV#DC/AC STRING INVERTERCLPCRITICAL LOADS PANEL SECTION 1 PV ARRAY TAGSECTION #MODULE GROUP PERFORMANCE METER UTILITY METER P M XFMR TRANSFORMER JUNCTION BOXJB RSD RAPID SHUTDOWNSUB-PANELSUB NORTH ESED EMERGENCY RSD SWITCHEMERGENCY DISCONNECTINV1ACSPMPATSBATTEDES JB JB SCALE: 1/8” = 1’0” @ SHEET SIZE A3QTY 38 Hanwha Q-cells Q.PEAK DUO-G7 330 MODULES QTY 1 GENERAC PWRcell 7.6 APKE00014 INVERTER E-100PV AC DISCONNECT LOCATED ON ACCESSIBLE EXTERIOR WALL WITH EXTERNAL HANDLE VISIBLE, LOCKABLE & LABELED WITHIN 10 FEET OF THE METER.Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT RELEASEREVDATE NAME ADDRESSAPNSTANDARD PLACARDS ADDRESS kW PHOTOVOLTAIC PLANSSHEET NOTES1SCALE:1/2" = 1'-0"CONDUIT, RACEWAY, J-BOX, AND PULL BOXES 2 3 5 6 7 SCALE:1/4" = 1'-0"8 9 4 1.PLACE ON CONDUIT AND/OR RACE WAYS EVERY 10' (60"), 12" FROM BENDS, 12" ABOVE AND BELOW PENETRATIONS. 2.CODE REFERENCE: NEC 690.31(G)(3)3.MINIMUM OF 1 1/8" x 5 3/4" 4.FONT: 3/8" AND .8 WIDTH FACTOR. 5.REFLECTIVE WHITE LETTERS ON A RED BACKGROUND. J-BOX, DC COMBINER, AND DC DISCONNECT WARNING:ELECTRIC SHOCK HAZARD. THE DCCONDUCTORS OF THIS PHOTOVOLTAICSYSTEM ARE UNGROUNDED AND MAYBE ENERGIZED SCALE:1/4" = 1'-0" 1.ONLY FOR UNGROUNDED SYSTEMS. 2.PLACED ON ALL ENCLOSURES WITH UNGROUNDED CIRCUITSOR DEVICES WHICH ARE ENERGIZED AND MAY BE EXPOSED DURING SERVICE. 3.CODE REFERENCE:NEC 690.35(F) 4.MINIMUM OF 3" x 10 1/2" 5.FONT: 3/8" 6.WHITE LETTERS ON A RED BACKGROUND. NON-LOAD BREAK DC COMBINER / J-BOX WARNING:ELECTRIC SHOCK HAZARDDO NOT TOUCH TERMINALSTERMINALS ON BOTH LINE AND LOADSIDES MAY BE ENERGIZED IN THEOPEN POSITION SCALE:1/2" = 1'-0" 1.PLACED ON DC DISCONNECT(S) AND ON ANY EQUIPMENT THAT STAYS ENERGIZED IN THE OFFPOSITION FROM THE PV SUPPLY. 2.CODE REFERENCE: NEC 690.17(E) 3.MINIMUM OF 3 1/2" x 10" 4.FONT: 3/8" 5.WHITE LETTERS ON A RED BACKGROUND. INVERTER(S)SCALE:1/2" = 1'-0" WARNING:ELECTRIC SHOCK HAZARDIF A GROUND FAULT IS INDICATED,NORMALLY GROUNDED CONDUCTORSMAY BE UNGROUNDED AND ENERGIZED 1.NORMALLY ALREADY PRESENT ON LISTED INVERTERS 2.CODE REFERENCE: NEC 690.5(C) 3.MINIMUM OF 3 1/2" x 10 1/2" 4.FONT: 3/8" 5.WHITE LETTERS ON A RED BACKGROUND. AC AND DC DISCONNECTS PHOTOVOLTAIC SYSTEM DISCONNECT 1.PLACE ON ALL AC AND DC DISCONNECTS 2.CODE REFERENCE: NEC 690.14(C)(2) 3.MINIMUM OF 1" x 10 1/2" 4.FONT: 3/8" 5.WHITE LETTERS ON A RED BACKGROUND. SCALE:1/4" = 1'-0"SCALE:1/4" = 1'-0" DC COMBINER BOX 1.CODE REFERENCE: NEC 690.16(B) AND NEC 690.17 2.USE PLACARD "COMBINER # 1" WHEN MORE THAN 1 DC COMBINER IS USED. NUMBER ACCORDING TO THREE LINE DIAGRAM AND CALCULATIONS. 3.MINIMUM OF 1" x 4" 4.FONT: 3/8" AND .75 TO .8 WIDTH FACTOR 5.WHITE LETTERS ON A RED BACKGROUND. 1.CODE REFERENCE: NEC 690.16(B) 2.USE ON NON-LOAD BREAK RATED DISCONNECTION. 3.MINIMUM OF 1" x 6" 4.FONT: 3/8" AND .8 WIDTH FACTOR 5.WHITE LETTERS ON A RED BACKGROUND. DC DISCONNECTS 1.USE PLACARD ON CUSTOMER GENERATION METER. 2.VERIFY WHICH PLACARD IS REQUIRED WITH AHJ. 3.MINIMUM OF 1" x 4" 4.FONT: 3/8" AND .8 WIDTH FACTOR 5.WHITE LETTERS ON A RED BACKGROUND. SOLAR kWh METER SCALE:1/2" = 1'-0" INVERTER # 1 1.USE PLACARD "INVERTER # 1" WHEN MORE THAN 1 INVERTER IS USED. NUMBER ACCORDING TO THREE LINE DIAGRAM AND CALCULATIONS. 2.MINIMUM OF 1" x 4" 3.FONT: 3/8" 4.WHITE LETTERS ON A RED BACKGROUND. SCALE:1/2" = 1'-0" USE PLACARD "[AC][DC] DISCONNECT # 1" WHEN MORE THAN ONE DISCONNECT IS USED. NUMBER ACCORDING TO THREE LINE DIAGRAM AND CALCULATIONS. 10 SCALE:1/4" = 1'-0"MAIN SERVICE PANEL 1.COMBINATION PLACARDS MAY BE USED IN PLACE OF MULTIPLE PLACARDS FOR THE SAME DEVICE. ALL INFORMATION FROM THE MULTIPLE PLACARDS MUST BE PRESENT. 2.BLACK LETTERS WITH YELLOW BACKGROUND MAY BE USED INPLACE OF THE STANDARD WHITE LETTERS WITH RED BACKGROUND WITH AHJ APPROVAL. 3.ALL INTERIOR AND EXTERIOR DC CONDUIT, ENCLOSURES, RACEWAYS, CABLE ASSEMBLIES, JUNCTION BOXES, COMBINERBOXES AND DISCONNECTS ARE MARKED. (IFC 605.11.1, NEC 690.31[E][3], NEC 690.31[E][4], 690.17 & 690.53) 4.THE MARKINGS ON THE CONDUITS, RACEWAYS AND CABLE ASSEMBLIES ARE EVERY 10 FEET, WITHIN ONE FOOT OF ALL TURNS OR BENDS AND WITHIN ONE FOOT ABOVE AND BELOW ALL PENETRATIONS OF ROOF/CEILING ASSEMBLIES, WALLS ANDBARRIERS. (IFC 605.11.1.4, NEC 690.31[E][3] &NEC 690.31[E][4]) 5.WHERE PV CIRCUITS ARE EMBEDDED IN BUILT-UP, LAMINATEOR MEMBRANE ROOFING MATERIALS IN ROOF AREAS NOT COVERED BY PV MODULES AND ASSOCIATED EQUIPMENT, THE LOCATION OF CIRCUITS SHALL BE CLEARLY MARKED. 6.REQUIRED LABELS SHALL BE PERMANENT AND SUITABLE FOR THE ENVIRONMENT. MATERIALS USED FOR MARKING MUST BE WEATHER RESISTANT. UL STANDARD IS RECOMMENDED TO DETERMINE WEATHER RATING. UL LISTING OF MARKINGS IS NOT REQUIRED. SEE UL LABELING SYSTEM 969 (UL 969) 7.MARKING CONTENT AND FORMAT: 7.1. ARIAL OR SIMILAR FONT, NON-BOLD. 7.2. MINIMUM 3/8" LETTER HEIGHT FOR HEADERS. 7.3. MINIMUM 1/16" LETTER HEIGHT FOR DATA 7.4. CONTRASTING BACKGROUND AND LETTERING. 7.5. ALL CAPITAL LETTERS. 7.6. CONTRASTING SPACE BETWEEN ROWS OF TEXT 7.7. DIMENSIONS OF PLACARDS ARE APPROXIMATE. MAY BE REDUCED AND / OR INCREASED TO UL APPROVED MANUFACTURED PRODUCT CODE ABBREVIATIONS:NATIONAL ELECTRICAL CODE (NEC) INTERNATIONAL BUILDING CODE (IBC) INTERNATIONAL RESIDENTIAL CODE (IRC) INTERNATIONAL FIRE CODE (IFC) UNDERWRITERS LABORATORY (UL) 90.5 ( )(1)(a . 3/8" B ACK CHARAC RS O YELLOW BACKGROU D, R A G CHARAC RS . 3/16" B ACK O WH BACKGROU D. L AT M THA 1 m FRO H S RV C D SCO M A S T WHI H TH PV SYST MS A T A SHALL I I AT TH L ATI ALL I TI I API SHUT W SWIT H S I T AT TH SAM L ATI . SOLAR PV SYSTEM EQUIPPED WITH RAPID SHUTDOWN TURN RAPID SHUTDOWN SWITCH TO THE “OFF” POSITION TO SHUT DOWN PV SYSTEM AND REDUCE SHOCK HAZARD IN THE ARRAY. SOLAR ELECTRIC PV PANELS 1.A RAPID SHUTDOWN SWITCH SHALL HAVE A LABEL LOCATEDON OR NO MORE THAN 1M (3 FT) FROM THE SWITCH THATINCLUDES THE FOLLOWING: 7 RAPID SHUTDOWN SWITCH RAPID SHUTDOWN SWITCH FOR SOLAR PV SYSTEM THE LABEL SHALL BE REFLECTIVE WITH ALL LETTERS CAPITALIZEDAND HAVING A MINIMUM HEIGHT OF 9.5 MM (3⁄8 IN.),IN WHITE ON RED BACKGROUND. 2. 1/4" = 1'-0"SCALE: INVERTERS P-001QTY 38 Hanwha Q-cells Q.PEAK DUO-G7 330 MODULES QTY 1 GENERAC PWRcell 7.6 APKE00014 INVERTER Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT RELEASEREVDATE NAME ADDRESSAPNSHEET NOTES1SCALE:1/4" = 1'-0"2 3 4 SCALE:1/4" = 1'-0" MAP PLACARD: MAIN SERVICE PANEL AND PV INVERTER (IF NOT SAME LOCATION) SCALE:1/4" = 1'-0"UTILITY METER, SERVICE PANEL, SUB-PANELAC DISCONNECT, AC SUB-PANEL MAXIMUM CIRCUIT CURRENT MAXIMUM VOLTAGE PV SYSTEM DC DISCONNECT ADC PHOTOVOLTAIC SYSTEM DC DISCONNECT MAX. CIRCUIT CURRENT MAXIMUM VOLTAGE ADC VDC RATED AC OUTPUT CURRENT AC NORMAL OPERATING VOLTAGE PV SYSTEM AC DISCONNECT AMPS VOLTS PHOTOVOLTAIC SYSTEM AC DISCONNECT RATED AC OUTPUT CURRENT AC NORMAL OPERATING VOLTAGE AMPS VOLTS WARNING DUAL POWER SOURCES RATED AC OUTPUT CURRENT AC NORMAL OPERATING VOLTAGE AMPS VOLTS SCALE:1/2" = 1'-0"5 CAUTION WARNING ELECTRIC SHOCK HAZARD - DO NOT TOUCH TERMINALS TERMINALS ON BOTH THE LINE AND LOAD SIDES MAY BE ENERGIZED IN THE OPEN POSITION MAP PLACARD: MAIN SERVICE PANEL AND PV INVERTER (IF NOT SAME LOCATION)SCALE:1/2" = 1'-0" CAUTION DC DISCONNECTS & DISCO. COMBINER DYNAMIC PLACARDSPV SYSTEM DC DISCONNECT PHOTOVOLTAIC SYSTEM DC DISCONNECT PV SYSTEM DC DISCONNECT PHOTOVOLTAIC SYSTEM DC DISCONNECT #1 #2 #3 RATED AC OUTPUT CURRENT AC NORMAL OPERATING VOLTAGE PV SYSTEM AC DISCONNECT AMPS VOLTS PHOTOVOLTAIC SYSTEM AC DISCONNECT RATED AC OUTPUT CURRENT AC NORMAL OPERATING VOLTAGE AMPS VOLTS RATED AC OUTPUT CURRENT AC NORMAL OPERATING VOLTAGE PV SYSTEM AC DISCONNECT AMPS VOLTS PHOTOVOLTAIC SYSTEM AC DISCONNECT RATED AC OUTPUT CURRENT AC NORMAL OPERATING VOLTAGE AMPS VOLTS BUILDING CONTAINS TWO SOURCES OF POWER: UTILITY, SOLAR PV UTILITY SERVICE DISCONNECT LOCATED BELOW. SOLAR PV SYSTEM DISCONNECT LOCATED [N/E/S/W] WALL OF BUILDING BUILDING CONTAINS TWO SOURCES OF POWER: UTILITY, SOLAR PV UTILITY SERVICE DISCONNECT LOCATED BELOW. SOLAR PV SYSTEM DISCONNECT LOCATED [N/E/S/W] WALL OF BUILDING STRING INVERTER #1 - INTEGRATED AC DISCONNECT RATED AC OUTPUT CURRENT AC NORMAL OPERATING VOLTAGE PV SYSTEM AC DISCONNECT AMPS VOLTS PHOTOVOLTAIC SYSTEM AC DISCONNECT RATED AC OUTPUT CURRENT AC NORMAL OPERATING VOLTAGE AMPS VOLTS STRING INVERTER #2 - INTEGRATED AC DISCONNECT AC DISCONNECT #1 - INDEPENDENT/ SEPARATE AC SUB-PANEL #1 ADDRESS kW PHOTOVOLTAIC PLANS#1 #2 #3 VDC MAXIMUM CIRCUIT CURRENT MAXIMUM VOLTAGE ADC MAX. CIRCUIT CURRENT MAXIMUM VOLTAGE ADC VDCVDC MAXIMUM CIRCUIT CURRENT MAXIMUM VOLTAGE ADC MAX. CIRCUIT CURRENT MAXIMUM VOLTAGE ADC VDCVDC 1.PRIME CONTRACTOR / PERMIT APPLICANT SIGNER IS RESPONSIBLE FOR THE DESIGN AND SPECIFICATIONS OF THE PHOTOVOLTAIC SYSTEM INSTALLATION. PRIME CONTRACTOR / PERMIT APPLICANT SIGNER WILL BE RESPONSIBLE FOR COLLECTION OF EXISTING ONSITE INFORMATION REQUIREMENTS TO DESIGN, SPECIFY, AND INSTALLTHE EXTERIOR MOUNTED PORTION OF THE PHOTOVOLTAIC SYSTEM DETAILED IN THIS DOCUMENT. 2.ADVANCED SOLAR SOLUTIONS, INC IS RESPONSIBLE FOR APPLYING SUPPLIED INFORMATION INTO A SET OF PERMIT DRAWINGS. ANY CHANGES TO DRAWINGS ARE SUBJECT TO CONTRACT CONDITIONS BETWEEN THE CLIENT AND ADVANCED SOLAR SOLUTIONS, INC. IN ACCORDANCE WITH THE REQUIREMENTS OF THE AHJ. RESPONSIBILITY NOTES N (E) UTILITY METER& SERVICE PANEL INVERTERW/ DC DISCO BATTERY PRODUCTIONMETER AC DISCO AUTOTRANSFERSWITCH SOLAR ARRAYON ROOF TOP 1.PLACARD PLACED ON EACH DISCONNECT, IF MORE THAN ONE PRESENT. 2.VALUES MUST MATCH EQUIPMENT CALCULATIONS. SEE SHEET "E-001 / DC DISCONNECT [#]" 3.CODE REFERENCE: NEC 690.53 4.MINIMUM OF 2 1/2" x 8" OR 5" x 2 1/2" RESPECTIVELY. 5.FONT: 3/8" HEADER, 3/16" DATA 6.WHITE LETTERS ON A RED BACKGROUND. 7.IN SOME CASES TWO LABELS MAY BE REQUIRED. AN INVERTER WITH INTEGRATED DC DISCONNECT UTILIZING TWO MPPT TRACKERS; IF CONFIGURATION USESDIFFERENT MODULES. 1.PLACARD PLACED ON EACH SOLAR SYSTEM DISCONNECTING COMPONENT. 2.VALUES MUST MATCH EQUIPMENT CALCULATIONS. SEE SHEET "E-001 / AC DISCONNECT [#]" 3.CODE REFERENCE: NEC 690.54 4.MINIMUM OF 1 1/2" x 8 1/2" OR 1 3/4" x 6 1/2" RESPECTIVELY. 5.FONT: 3/8" HEADER, 3/16" DATA 6.WHITE LETTERS ON A RED BACKGROUND. 1.(#1) PLACARD PLACED AT MAIN UTILITY SERVICE DISCONNECT/BREAKER AND PV SYSTEM SUPPLY BREAKER AT POINT OF INTERCONNECTION. (#2 & #3) PLACARD(S)REQUIRED WITH #1 PLACARD WHEN UTILITY SERVICE AND PV SYSTEM DISCONNECT(S) ARENOT LOCATED NEXT TO EACH OTHER. MAP PLACARD REQUIRED AS SPECIFIED. 2.VALUES MUST MATCH EQUIPMENT CALCULATIONS. 2.1. VALUES WILL MATCH LOAD CENTER OR SUB-PANEL VALUES IF INSTALLED AFTERINVERTERS. IF AC CONNECTION TO SERVICE PANEL COMES FROM INVERTERS; SEESHEET "E-001 / STRING INVERTER[#] SPECIFICATIONS".2.1.1. INVERTERS ARE PARALLEL CONNECTIONS. 2.1.2. "RATED AC OUTPUT CURRENT" WILL BE THE SUM OF THE INVERTERS 2.1.3. "AC NORMAL OPERATING VOLTAGE" WILL BE THE NAME PLATE RATING OF THEINVERTER 3.CODE REFERENCE: NEC 690.54, NEC 705.12(D)(3) 4.MINIMUM OF 2" x 6 1/2" (#1), VARIES (#2 & #3) 5.FONT: 3/8" HEADER, 3/16" DATA (#1), 1/4" (#2 & #3) 6.WHITE LETTERS ON A RED BACKGROUND. ITH COMBINED WARNING PLACARD IF REQUIRED. EXAMPLE: LADWP) 1.PLACARD PLACED AT ELECTRICAL SERVICE AND AT THE PV 2. MAP PLACARD PROVIDES A DIRECTORY OF THE SERVICEDISCONNECTING MEANS AND PHOTOVOLTAIC SYSTEMDISCONNECTION MEANS. 3. CODE REFERENCE: NEC 690.56(A)(B), 705.10 4. WHITE LETTERS ON A RED BACKGROUND. 5. MINIMUM OF 7 3/4" x 5" 6. FONT: 3/4" "CAUTION", 1/4" "WARNING", 3/16" HEADER,1/8" DATA AND NOTES 7.PLACARD WILL BE PLACED ADJACENT TO THE MAIN SERVICEDISCONNECT IN A LOCATION CLEARLY VISIBLE FROM WHERETHE DISCONNECT IS OPERATED. (IFC 605.11.1.3) INVERTER AND PV DISCONNECTS IF NOT AT THE SAME LOCATION.1.PLACARD PLACED AT ELECTRICAL SERVICE AND AT THE PV INVERTER AND PV DISCONNECTS IF NOT AT THE SAME LOCATION. 2.MAP PLACARD PROVIDES A DIRECTORY OF THE SERVICE DISCONNECTING MEANS AND PHOTOVOLTAIC SYSTEM DISCONNECTION MEANS. 3.CODE REFERENCE: NEC 690.56(A)(B), 705.10 4.WHITE LETTERS ON A RED BACKGROUND. 5.MINIMUM OF 6 1/2" x 6 1/2" 6.FONT: 3/4" "CAUTION", 1/4" HEADER, 1/8" DATA AND NOTES 7.PLACARD WILL BE PLACED ADJACENT TO THE MAIN SERVICE DISCONNECT IN A LOCATION CLEARLY VISIBLE FROM WHERE THE DISCONNECT IS OPERATED. (IFC 605.11.1.3) 1. 2. 3. 4. COMBINATION PLACARDS MAY BE USED IN PLACE OF MULTIPLE PLACARDS FOR THE SAME DEVICE. ALL INFORMATION FROM THE MULTIPLE PLACARDS MUST BE PRESENT. BLACK LETTERS WITH YELLOW BACKGROUND MAY BE USED IN PLACE OF THE STANDARD WHITE LETTERS WITH RED BACKGROUND WITH AHJ APPROVAL. ALL INTERIOR AND EXTERIOR DC CONDUIT, ENCLOSURES, RACEWAYS, CABLE ASSEMBLIES, JUNCTION BOXES, COMBINER BOXES AND DISCONNECTS ARE MARKED. (IFC 605.11.1, NEC 690.31[E][3], NEC 690.31[E][4], 690.17 & 690.53) REQUIRED LABELS SHALL BE PERMANENT AND SUITABLE FOR THE ENVIRONMENT. MATERIALS USED FOR MARKING MUST BE WEATHER RESISTANT. UL STANDARD IS RECOMMENDED TO DETERMINE WEATHER RATING. UL LISTING OF MARKINGS IS NOT REQUIRED. SEE UL LABELING SYSTEM 969 (UL 969) 5.MARKING CONTENT AND FORMAT: 5.1. ARIAL OR SIMILAR FONT, NON-BOLD. 5.2. MINIMUM 3/8" LETTER HEIGHT FOR HEADERS.5.3. MINIMUM 1/16" LETTER HEIGHT FOR DATA 5.4. CONTRASTING BACKGROUND AND LETTERING. 5.5. ALL CAPITAL LETTERS. 5.6. CONTRASTING SPACE BETWEEN ROWS OF TEXT5.7. DIMENSIONS OF PLACARDS ARE APPROXIMATE. MAY BEREDUCED AND / OR INCREASED TO UL APPROVED MANUFACTURED PRODUCT 6.ANSI Z535.4-2014 PRODUCT SAFETY SIGNS AND LABELS: THISINFORMATIONAL NOTE AND ITS REQUIREMENTS FOR PLACARDS MAY BE USED WITH PRIOR APPROVAL OF THE AHJ. MOSTNOTABLE DIFFERENCES IS COLOR OF PLACARDS AND USE OFHAND WRITTEN VALUES WITH INDUSTRIAL MARKERS ON STANDARD PLACARDS WHERE THE VALUE MAY CHANGE AT A FUTURE DATE. I.E. ADDING MODULES AT A FUTURE DATE, OR STANDARD PLACARD MANUFACTURER INSTALLED ON ELECTRICAL COMPONENT. AHJ APPROVAL REQUIRED. (SEE NOTE #1 FOR INDIVIDUAL PLACARDS) CODE ABBREVIATIONS:NATIONAL ELECTRICAL CODE (NEC) INTERNATIONAL BUILDING CODE (IBC) INTERNATIONAL RESIDENTIAL CODE (IRC) INTERNATIONAL FIRE CODE (IFC) UNDERWRITERS LABORATORY (UL) DISCO.&BATTERYRSD SWITCHEMERGENCY N (E) UTILITY METER& SERVICE PANEL INVERTERW/ DC DISCO BATTERY PRODUCTIONMETER AC DISCO AUTOTRANSFERSWITCH EMERGENCYRSD SWITCH&BATTERYDISCO.SOLAR ARRAYON ROOF TOP 32240240 324040 240364364 32 240 32 32 240 P-002Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT Generac Power Systems, Inc.S45 W29290 Hwy. 59, Waukesha, WI 53189www.Generac.com 1-888-GENERAC (1-888-436-3722) 7.6kW 1Ø, 11.4kW 3Ø PWRcell Inverter w/ CTs and CT Adapter Model: APKE00014, APKE00013 Solar-plus-storage is simple with the Generac PWRcell Inverter. This bi-directional, REbus™-powered inverter o ers a simple, e cient design for integrating smart batteries with solar. Ideal for self-supply, backup power, zero-export and energy cost management, the PWRcell inverter is the industry’s most feature-rich line of inverters, available in single-phase and thr ee-phase models. ADDITIONAL FEATURES • Single inverter for grid-tied solar with smart battery integration • Simplified system design: No autotransformer or battery inverter needed • User-selectable modes for backup power, self-supply, time-of-use and zero-export • Free system monitoring included via PWRview Web Portal and Mobile App FEATURES: No autotransformer or battery inverter needed User-selectable modes Free system monitoring AC OUTPUT/ GRID-TIE MODEL APKE00014 MODEL APKE00013 RATED AC POWER OUTPUT 7600 W 11400 W AC OUTPUT VOLTAGE 120/240, 1Ø VAC 120/208, 3Ø VAC AC FREQUENCY 60 Hz 60 Hz MAXIMUM CONTINUOUS OUTPUT CURRENT 32 A, RMS 32 A, RMS GROUND FAULT ISOLATION DETECTION Included Included CHARGE BATTERY FROM AC Yes Yes THD CURRENT < 2 %< 2 % TYPICAL NIGHTTIME POWER CONSUMPTION < 7 W < 7 W AC OUTPUT/ BACKUP MODEL APKE00014 MODEL APKE00013 RATED AC BACKUP POWER OUTPUT 8000 W 8000 W MAXIMUM AC BACKUP POWER OUTPUT 10000 W 10000 W AC BACKUP OUTPUT VOLTAGE 120/240, 1Ø VAC 120/240, 1Ø VAC AC FREQUENCY 60 HZ 60 HZ AC CIRCUIT BREAKER 50 A 50 A THD VOLTAGE < 2 %< 2 % AUTOMATIC SWITCHOVER TIME < 1 Seconds < 1 Seconds TYPICAL NIGHTTIME POWER CONSUMPTION 30 W 30 W DC INPUT MODEL APKE00014 MODEL APKE00013 DC INPUT VOLTAGE RANGE 360 420 VDC 360 420 VDC NOMINAL DC BUS VOLTAGE 380 VDC 380 VDC MAX INPUT CURRENT 20 A 30 A REVERSE POLARITY PROTECTION YES YES GROUND FAULT ISOLATION DETECTION YES YES TRANSFORMERLESS, UNGROUNDED YES YES DC INPUT/ BATTERY MODEL APKE00014 MODEL APKE00013 MAXIMUM CONTINUOUS POWER 8000 W 8000 W INTERNAL DC DISTRIBUTION BREAKERS 4X 2P30A 4X 2P30A DC FUSES ON PLUS AND MINUS 40 A 40 A 2 POLE DISCONNECTION YES YES EFFICIENCY MODEL APKE00014 MODEL APKE00013 PEAK EFFICIENCY 97 %98 % CEC WEIGHTED EFFICIENCY 96.5 %97.5 % Generac Power Systems, Inc.S45 W29290 Hwy. 59, Waukesha, WI 53189www.Generac.com 1-888-GENERAC (1-888-436-3722) Specifications Specifications subject to change without notice. FEATURES AND MODES ISLANDING3 Yes GRID SELL Yes SELF CONSUMPTION Yes PRIORITIZED CHARGING FROM RENEWABLES Yes GRID SUPPORT ZERO EXPORT Yes ADDITIONAL FEATURES SUPPORTED COMMUNICATION INTERFACES CANbus, RS4854, Ethernet SYSTEM MONITORING PWRview Web Portal and Mobile App CRITICAL LOADS DISCONNECT3 Yes MANUAL INVERTER BYPASS SWITCH Automatic WARRANTY 10 Years STANDARDS COMPLIANCE SAFETY UL1741 SA, CSA 22.2 GRID CONNECTION STANDARDS IEEE1547, Rule 21, Rule 14H EMISSIONS FCC part15 class B DIMENSIONS AND INSTALLATION SPECIFICATIONS WIRE GAUGE RANGE 10 - 8 AWG TOTAL AC KNOCKOUTS X SIZE 2“ x 0.75“, 2 x 1“ TOTAL DC KNOCKOUTS X SIZE 5“ x 1“ DIMENSIONS L,W,H 24.5“ x 19.25“ x 8“ WEIGHT 62.7 lb COOLING Forced convection NOISE < 40 dBA OPERATING TEMPERATURE -20 to 50 °C* PROTECTION RATING NEMA 3R INSTALLATION GUIDELINES BATTERY TYPES SUPPORTED PWRcell battery module MODULE STRING SIZE PER PV LINK OPTIMIZER 2-9 PV modules MAXIMUM RECOMMENDED DC POWER FROM PV 10kW (1Ø), 15kW (3Ø) BATTERIES PER INVERTER Up to 2 3 3Ø inverters o er islanding for 1Ø loads, 4 Modbus,*Reduced power at extreme temperatures RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSINVERTER CUT SHEET R-101Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSDC/DC CONVERTERS CUT SHEET R-102Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSModel APKE00007, PWRcell Battery CabinetModel A0000391219, 2.85kWh PWRcell Battery ModuleCertification Model Reference: BJ-DCB05ZKAXModel APKE00008, PWRcell Spacer KitModel APKE00009, PWRcell Upgrade KitCertification Model Reference for Battery Configurations: PWRcell 9, PWRcell 12, PWRcell 15, PWRcell 17 FEATURES & BENEFITS • Connect 2 PWRcell Battery Cabinets to a single PWRcell Inverter for 34.2kWh of storage • Best-in-class battery backup power • Plug-and-play with PWRcell Inverter and PV Link™ • Time-of-use (TOU) and zero-export ready • Residential and commercial application ready BATTERY CONFIGURATION GUIDE BATTERY CABINET ASSEMBLY PWRcellBattery Cabinet PWRcell 1717.1kWh 6x Battery Module PWRcell 1514.3kWh 5x Battery Module+ Module Spacer Kit PWRcell 1211.4kWh 4x Battery Module PWRcell 98.6kWh 3x Battery Module+ Module Spacer Kit OR OR OR SPACER SPACER PWRcellBattery CabinetBack PanelModuleSpacer Kitx1 BatteryModulex5PWRcellBattery CabinetFront Panel The PWRcell™ Battery Cabinet is a modular smart battery platform that allows for a range of configurations to suit any need, small or large. No other smart battery o ers the power and flexibility of PWRcell. Whether for backup power or smart energy management, PWRcell has power and capacity options for every need, without sacrificing flexibility or function. PWRcell BATTERY CABINET DESIGN The PWRcell Battery Cabinet allows system owners the flexibility to scale from the economical 8.6kWh PWRcell 9 to the massive 17.1kWh PWRcell 17 by installing additional battery modules to the PWRcell Battery Cabinet. When needs change, an existing PWRcell Battery Cabinet can be upgraded with additional modules. Use the graphic below and the chart on the back of this sheet to understand what components you need for your chosen PWRcell configuration. Specifications Generac Power Systems, Inc. S45 W29290 Hwy. 59, Waukesha, WI 53189 www.Generac.com | 888-GENERAC (436-3722) A0000528139 REV C ©2020 Generac Power Systems. All rights reserved. Specifications are subject to change without notice. UPGRADING PWRcell Inside of the PWRcell Battery Cabinet, battery modules are stacked two deep on three levels, allowing for up to six modules to be connected in series. You can upgrade an existing PWRcell Battery Cabinet by adding Battery Modules and a Module Spacer (APKE00008) if required. PWRcell 9 and PWRcell 15 require a module spacer. Generac o ers a convenient PWRcell Battery Upgrade Kit (APKE00009) to help replace lost or misplaced hardware. A PWRcell Battery Upgrade Kit may be purchased from your Generac distributor. Refer to the table to the right for material requirements related to upgrading the PWRcell Battery Cabinet. UPGRADE MATERIAL REQUIREMENTS ENDING CONFIGURATION STARTING CONFIGURATIONPWRcell 17 PWRcell 15 PWRcell 12 PWRcell 9 + 3 x PWRCell Mod+ 2 x APKE00009*+ 2 x PWRCell Mod+ 1 x APKE00009*+ 1 x PWRCell Mod+ 1 x APKE00009* PWRcell 12 + 2 x PWRCell Mod+ 1 x APKE00009*+ 1 x PWRCell Mod+ 1 x APKE00008 PWRcell 15 + 1 x PWRCell Mod+ 1 x APKE00009* *APKE00009 (Upgrade kit) only required if original hardware is unavailable PWRcell™ BATTERY CONFIGURATIONS 9 12 15 17 BATTERY MODULES:3 4 5 6 USABLE ENERGY:8.6kWh 11.4kWh 14.3kWh 17.1kWh POWER RATED CONTINUOUS: 3.4kW 4.5kW 5.6kW 6.7kW POWER 60 MINUTES:4.2kW 5.6kW 7.0kW 8.4kW POWER 2 MINUTES:5.0kW 6.7kW 8.4kW 10.0kW REbus™ VOLTAGE INPUT/OUTPUT:360-420 VDC MODULE VOLTAGE:46.8 VDC ROUND TRIP EFFICIENCY:96.50% OPERATING TEMPERATURE FAHRENHEIT CELSIUS :41 to 113 °F 5 to 45 °C RECOMMENDED AMBIENT TEMPERATURE FAHRENHEIT CELSIUS : 55 to 86 °F 13 to 30 ºC MAXIMUM INSTALLATION ALTITUDE FT M :9834 (3000) DIMENSIONS, L x W x H IN MM :22" x 10" x 68" 559 x 254 x 1727 WEIGHT, ENCLOSURE LB KG :115 (52) WEIGHT, INSTALLED LB KG :280 (127)335 (152)390 (178)445 (202) WARRANTY LI ION MODULES:10 Years, (7.56MWh) WARRANTY ELECTRONICS AND ENCLOSURE:10 Years COMMUNICATION PROTOCOL:REbus™ DC Nanogrid™ COMPLIANCE:UL 9540, UL 1973, UL 1642, CSA 22.2 BATTERY CUT SHEET R-103Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT snapnrack.com Ultra Rail Industry leading Wire Management Solutions Single Tool Installation Mounts available for all roof types All SnapNrack Module Clamps & Accessories are compatible with both raiil profi les Start Installing Ultra Rail Today UR-40 UR-60 The Ultimate Value in Rooftop Solar Solar Mounting Solutions © 2016 by SnapNrack Solar Mounting Solutions. All rights reserved 877-732-2860 www.snapnrack.com contact@snapnrack.com SnapNrack_Ultra Rail Sales Brochure_v.1.4 SnapNrack Solar Mounting Solutions are engineered to optimize material use and labor resources and improve overall installation quality and safety. Quality. Innovative. Superior. Unparalleled Wire Management • Open rail channel provides room for running wires resulting in a long-lasting quality install • Industry best wire management o ering includes Junction Boxes, Universal Wire Clamps, MLPE Attachment Kits, and Conduit Clamps • System is fully bonded and listed to UL 2703 Standard © 2019 by SnapNrack Solar Mounting Solutions. All rights reserved 877-732-2860 www.snapnrack.com contact@snapnrack.com SnapNrack Ultra Rail System A sleek, straightforward rail solution for mounting solar modules on all roof types. Ultra Rail features two rail profi les; UR-40 is a lightweight rail profi le that is suitable for most geographic regions and maintains all the great features of SnapNrack rail, while UR-60 is a heavier duty rail profi le that provides a larger rail channel and increased span capabilities. Both are compatible with all existing mounts, module clamps, and accessories for ease of install. The Entire System is a Snap to Install • New Ultra Rail Mounts include snap-in brackets for attaching rail • Compatible with all the SnapNrack Mid Clamps and End Clamps customers love • Universal End Clamps and snap-in End Caps provide a clean look to the array edge Heavy Duty UR-60 Rail • UR-60 rail profi le provides increased span capabilities for high wind speeds and snow loads • Taller, stronger rail profi le includes profi le- specifi c rail splice and end cap • All existing mounts, module clamps, and accessories are retained for the same great install experience RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSRACKING & RAIL CUT SHEET R-104Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT DESCRIPTION: PART NUMBER(S): DRAWN BY: SNAPNRACK, UR-40 RAIL 232-02449, 232-02450, 232-02451 mwatkins Solar Mounting Solutions THE INFORMATION IN THIS DRAWING IS CONFIDENTIAL AND PROPRIETARY. ANYREPRODUCTION, DISCLOSURE, OR USE THEREOF IS PROHIBITED WITHOUT THEWRITTEN CONSENT OF SUNRUN SOUTH LLC. 595 MARKET STREET, 29TH FLOOR ● SAN FRANCISCO, CA 94105 USAPHONE (415) 580-6900 ● FAX (415) 580-6902B REVISION: MATERIALS: DESIGN LOAD (LBS): ULTIMATE LOAD (LBS): TORQUE SPECIFICATION: CERTIFICATION: WEIGHT (LBS): 6000 SERIES ALUMINUM N/A N/A N/A LB-FT UL 2703, FILE E359313 5.85 OPTIONS: CLEAR / BLACK ANODIZED MILL FINISH BUNDLES OF 144 BOXES OF 8 ALL DIMENSIONS IN INCHES UR-40 RAILPROPERTIES SKU FINISH 232-02449 MILL 232-02450 CLEAR232-02451 BLACK 1.624 1.500 CENTROID .750 .832 .792 SECTION PROPERTIES A 0.357 in² Ixx 0.125 in⁴ Iyy 0.132 in⁴ Sx (TOP)0.150 in³ Sx (BOT)0.158 in³ Sy (LEFT)0.175 in³ Sy (RIGHT)0.175 in³ DESCRIPTION: PART NUMBER(S): DRAWN BY: SNAPNRACK, UR-40 SPLICE 242-01213, 242-01214 mwatkins Solar Mounting Solutions THE INFORMATION IN THIS DRAWING IS CONFIDENTIAL AND PROPRIETARY. ANYREPRODUCTION, DISCLOSURE, OR USE THEREOF IS PROHIBITED WITHOUT THEWRITTEN CONSENT OF SUNRUN SOUTH LLC. 595 MARKET STREET, 29TH FLOOR ● SAN FRANCISCO, CA 94105 USAPHONE (415) 580-6900 ● FAX (415) 580-6902A REVISION: MATERIALS: DESIGN LOAD (LBS): ULTIMATE LOAD (LBS): TORQUE SPECIFICATION: CERTIFICATION: WEIGHT (LBS): 6000 SERIES ALUMINUM, STAINLESS STEEL N/A N/A 12 LB-FT UL 2703, FILE E359313 0.52 OPTIONS: CLEAR / BLACK ANODIZED PARTS LIST DESCRIPTIONQTYITEM SNAPNRACK, UR-40 SPLICE TAPPED PRC, CLEAR11 SNAPNRACK, UR-40 SPLICE THRU PRC, CLEAR12 SNAPNRACK, SNAPLINK BONDING CLIP, TYPE 2, STEEL23 BOLT, FLANGE, SERRATED, 5/16IN-18 X 1-3/4IN, SS14 1 2 4 3 RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSRACKING & RAIL CUT SHEET R-105Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT DESCRIPTION: PART NUMBER(S): DRAWN BY: SNAPNRACK, UR-60 RAIL 232-02481, 232-02482, 232-02483 mwatkins Solar Mounting Solutions THE INFORMATION IN THIS DRAWING IS CONFIDENTIAL AND PROPRIETARY. ANYREPRODUCTION, DISCLOSURE, OR USE THEREOF IS PROHIBITED WITHOUT THEWRITTEN CONSENT OF SUNRUN SOUTH LLC. 595 MARKET STREET, 29TH FLOOR ● SAN FRANCISCO, CA 94105 USAPHONE (415) 580-6900 ● FAX (415) 580-6902A REVISION: MATERIALS: DESIGN LOAD (LBS): ULTIMATE LOAD (LBS): TORQUE SPECIFICATION: CERTIFICATION: WEIGHT (LBS): 6000 SERIES ALUMINUM N/A N/A N/A LB-FT UL 2703, FILE E359313 8.46 OPTIONS: CLEAR / BLACK ANODIZED MILL FINISH BUNDLES OF 120 BOXES OF 8 ALL DIMENSIONS IN INCHES UR-60 RAILPROPERTIESSKUFINISH 232-02481 MILL 232-02482 CLEAR232-02483 BLACK CENTROID .750 1.211 1.039 SECTION PROPERTIES A 0.515 in² Ixx 0.327 in⁴ Iyy 0.181 in⁴ Sx (TOP)0.270 in³ Sx (BOT)0.315 in³ Sy (LEFT)0.242 in³ Sy (RIGHT)0.242 in³ 2.250 1.500 DESCRIPTION: PART NUMBER(S): DRAWN BY: SNAPNRACK, UR-60 SPLICE 242-01270, 242-01271 mwatkins Solar Mounting Solutions THE INFORMATION IN THIS DRAWING IS CONFIDENTIAL AND PROPRIETARY. ANYREPRODUCTION, DISCLOSURE, OR USE THEREOF IS PROHIBITED WITHOUT THEWRITTEN CONSENT OF SUNRUN SOUTH LLC. 595 MARKET STREET, 29TH FLOOR ● SAN FRANCISCO, CA 94105 USAPHONE (415) 580-6900 ● FAX (415) 580-6902B REVISION: MATERIALS: DESIGN LOAD (LBS): ULTIMATE LOAD (LBS): TORQUE SPECIFICATION: CERTIFICATION: WEIGHT (LBS): 6000 SERIES ALUMINUM, STAINLESS STEEL FULL UR-60 RAIL CAPACITY N/A 12 LB-FT UL 2703, FILE E359313 0.71 OPTIONS: CLEAR / BLACK ANODIZED PARTS LIST DESCRIPTIONQTYITEM BOLT, FLANGE, 5/16IN-18 X 3/4IN, CLEAR, SS11 SNAPNRACK, UR-60 SPLICE, SLEEVE, CLEAR / BLACK12 SNAPNRACK, O-RING13 SNAPNRACK, UR-60 SPLICE, BONDING BRIDGE14 1 4 3 2 RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSRACKING & RAIL CUT SHEET R-106Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT snapnrack.com 51 System Bonding Methods Grounding Specifications RAIL CHANNEL NUT MODULEFRAME MID CLAMP ASSEMBLY SS BONDING PIN NOTE: SnapNrack Mid Clamp SnapNrack Adjustable End Clamp SnapNrack UR-40 Rail Splice SnapNrack UR-60 Rail Splice q SnapNrack module clamps contain a SnapNrack Channel Nut with integral bonding clips or pins in assembly to properly bond the system (except Universal End Clamps). Note: SnapNrack Ground Lug Assembly SNAPNRACKULTRA SERIES RAIL 5/16"-18 X 1" BOLT S.S.WITH SPLIT LOCK WASHER S.S. SNAPNRACK GROUNDLUG, 6-12 AWG SNAPNRACK BONDINGCHANNEL NUT COPPER WIRE, TYP. SS BONDING CLIP(2 TOTAL)RAIL SPLICE ASSEMBLY SnapNrack Ultra Rail Splices contain integral bonding clips in assembly to properly bond the system. Note: RAIL SPLICEASSEMBLY SS BONDING PIN(2 TOTAL) snapnrack.com 52 Grounding Specifications Ground Path Details Ilsco Lay-in Lug Assembly SNAPNRACKULTRA SERIES RAIL #10 BOLT SS ILSCO GBL-4DBT GROUND LUG #10 NUT SSWITH STAR WASHER COPPER WIRE, TYP. GROUND PATH RAIL RAIL SPLICE GROUND LUG EQUIPMENT GROUNDING CONDUCTOR M M M M M M M M X X U U U U U U X X U U TO EGC MOUNT M MODULE CLAMP M = MIDCLAMP X = X-END CLAMPU = UNIVERSAL END CLAMP TO EGC RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSRACKING & RAIL CUT SHEET R-107Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT snapnrack.com 53 Grounding Specifications GROUND PATH RAIL RAIL SPLICE GROUND LUG EQUIPMENT GROUNDINGCONDUCTOR M M M M M M M M X X U U U U U U X X U U TO EGC MOUNT M MODULE CLAMPM = MIDCLAMPX = X-END CLAMP U = UNIVERSAL END CLAMP ENPHASEMICRO-INVERTER GROUND PATH RAIL RAIL SPLICE GROUND LUG EQUIPMENT GROUNDINGCONDUCTOR M M M M M M M M X X U U U U U U X X U U MOUNT M MODULE CLAMPM = MIDCLAMPX = X-END CLAMPU = UNIVERSAL END CLAMP SOLAREDGEOPTIMIZER TO EGC TO EGC Ground Path Details - Enphase Ground Path Details - SolarEdge snapnrack.com 54 INSTALLATION INSTRUCTIONS - SNAPNRACK GROUND LUG 1) Snap the SnapNrack Ground Lug into the rail channel on one rail per module row. 2) Place grounding conductor into slot underneath split ring washer. SnapNrack Ground Lug may be used in side or top channel, and may be rotated 90 degrees relative to slot to facilitate running copper across top of rails. Install Note: SnapNrack Ground Lug only Listed for use with 6-12 AWG solid copper conductor. Install Note: 3) Tighten hardware to 16 ft-lbs. Grounding Specifications INSTALLATION INSTRUCTIONS - ILSCO LAY-IN LUG 1) Drill and deburr a 1/4” hole in the back side of the rail for the Ilsco lug to attach to, place the bolt through the hole, and attach the lug assembly on one rail per module row. 2) Place grounding conductor into slot. Torque rail connection to 35 in-lbs. Install Note: Torque set screw to 20 in-lbs for #10- #14 solid and stranded copper, 25 in-lbs for #8 stranded copper, and 35 in-lbs for #4-#6 stranded copper. Install Note: 3) Tighten set screw per Ilsco’s recommendation (see below). • System has been evaluated to a maximum overcurrent device (OCD) protection level of 20 Amps. • Universal End Clamp (UEC) does not bond module to rail. Be sure to separately ground any modules that are only secured by UECs, especially during servicing. • SnapNrack recommends that bare copper never come into contact with aluminum.• SnapNrack Ground Lug: torque bolt to 16 ft-lbs. The Ground Lug may be used in side or top channel. It may be rotated 90 degrees relative to slot to facilitate running copper across top of rails. • Grounding with a standard Ilsco GBL-4DBT Lug is a listed alternate and requires drilling of a hole in the rail. • Ilsco hardware connection to rail: 5 ft-lbs. Torque for lug set screw: #10-#14 solid and stranded copper- 20 in-lbs, #8 stranded copper- 25 in-lbs, #4-#6 stranded copper- 35 in-lbs. Note:RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSRACKING & RAIL CUT SHEET R-108Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT snapnrack.com 55 Ground Path Details - DynoBond Grounding Specifications GROUND PATH RAIL RAIL SPLICE GROUND LUG EQUIPMENT GROUNDING CONDUCTOR(+)(-)(+)(-)(+)(-)(+)(-)(+)(-)(+)(-)(+)(-)M M M M M M M M E E TO EGC MOUNT M MODULE CLAMPM = MIDCLAMPE = END CLAMP(+)(-)E E M M M M E E E E DYNORAXX DYNOBOND R/C (QIMS2), DynoRaxx (E357716) photovoltaic bonding jumper cat. no. DynoBond is an optional component that may be used with this system. The DynoBond jumper has been evaluated to provide module to module bonding. The DynoBond device attaches to the frame flange of adjacent modules. August 6 1/923 RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSRACKING & RAIL CUT SHEET R-109Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT SnapNrack 775 Fiero Lane, Ste. 200 San Luis Obispo, CA 93401 TEL: (877) 732-2860 Attn.: SnapNrack - Engineering Department Subject: Engineering Certification for the State of Massachusetts Building Codes:1.ASCE/SEI 7-10, Minimum Design Loads for Buildings and Other Structures, by American Society of Civil Engineers 2.2015 International Building Code, by International Code Council, Inc. 3.2015 International Residential Code, by International Code Council, Inc. 4.AC428, Acceptance Criteria for Modular Framing Systems Used to Support Photovoltaic (PV) Panels, November 1, 2012 by ICC-ES 5.Aluminum Design Manual 2015, by The Aluminum Association, Inc. 6.ANSI/AWC NDS-2015, National Design Specification for Wood Construction, by the American Wood Council Design Criteria:Risk Category II Seismic Design Category = A - E Basic Wind Speed (ultimate) per ASCE 7-10: up to 190 mph Ground Snow Load = 0 to 120 (psf) This letter certifies that the loading criteria and design basis for the SnapNrack Ultra Rail Racking System with UR-60 Rail Span Tables are in compliance with the above codes. If you have any questions on the above, do not hesitate to call. Prepared by: PZSE, Inc. – Structural Engineers Roseville, CA August 6, 2019 PZSE, Inc. – Structural Engineers has provided engineering and span tables for the SnapNrack Ultra Rail Racking System with UR- 60 Rail, as presented in PZSE Report # 2018-11940.03, "Engineering Certification and Span Tables for the SnapNrack Ultra Rail Solar Photovoltaic Racking System". All information, data, and analysis therein are based on, and comply with, the following building codes and typical specifications: Re: Report # 2018-11940.03 – SnapNrack Ultra Rail Solar Photovoltaic Racking System with UR-60 Rail RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSRACKING & RAIL CUT SHEET R-110Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT v102016 MADE IN USA MADE WITH RECYCLED MATERIAL © 2016 Zilla Corporation. All rights reserved. 77 Waneka Pkwy • Lafayette, CO 80026 • 720.880.6700 • fax 303.664.1268 • zillarac.com Zilla® So Simple It’s ScarySM 2 U P U SD DSSO KL SU XF L FOX L ZL K X OLPL D L 86 3D D U 6 / ;/ 6 / /. ;/ LOOD RXEOH WXG / )ODV L J 2 Z LOOD RXEOH WXG / )ODV L J DWWDF HV WR V HDW L J RU VWUXFWXUDO PHPEHUV IRU IDVWHU VDIHU D G HDVLHU L VWDOODWLR V R FRPSRVLWLR DVS DOW V L JOH URRIV DWH WHG EDVH SODWH GHVLJ Z W W S WW W S W provides speed and exibility in the eld for securing to sheathing or structural members. Low pro le patented design S W W W W S zone that creates a complete water tight seal while ensuring integrity of the structure during expansion and contraction. RPSDWLEOH Z W ush mount system or any solar mounting system of your choice. LOOD RXEOH WXG / )ODV L J 7UD VSDUH W VVHPEO Sheathing attachment 6W W WW W 0LOO FXVWRP ODFN )ODV L J DYDLODEOH L 0LOO D G FXVWRP FRORUV FDOO IRU GHWDLOV D G DYDLO DELOLW PL LPXP RUGHUV PD DSSO v102016 MADE IN USA MADE WITH RECYCLED MATERIAL © 2016 Zilla Corporation. All rights reserved. 77 Waneka Pkwy • Lafayette, CO 80026 • 720.880.6700 • fax 303.664.1268 • zillarac.com Zilla® So Simple It’s ScarySM 2 U P U SD DSSO KL SU XF L FOX L ZL K X OLPL D L 86 3D D U 6 / ;/ 6 / /. ;/ LOOD RXEOH WXG / )ODV L J Technical Speci cations Zilla )ODV L J / Zilla RXEOH tud ZilOD DVH Plate XL LOOD RXEOH WXG / )ODV L J LOOD RXEOH WXG )ODV L J / is available in Black (ZDSFA-AL BLK XL) or custom colors and includes: Double Stud with Encapsulated Gland Washer, Flashing XL and Base Plate XL. LOOD RXEOH WXG is a 3/8”-16 x 1-1/2” stainless steel stud with 3/16” recessed hex and 1-3/8” hex aluminum nut. Sheathing attachment 6W W WW W PRODUCT DESCRIPTION MATERIALS SIZE COLOR Double Stud Provides mechanical connection between Flashing and Quad Combo XL. 66 GZ G S W G gland washer included. Aluminum 66 1-3/8” Hex x 1.5” Flashing XL Sits on top of the Base Plate XL, and iscaptured by the Double Stud.26 ga.Aluminum 15” L x 9-7/8” Wx 1/2” H Black Base Plate XL Base Plate is attached to the roof with lags. Flashing is attached to the Base Plate using the Mini Standoff. G 6W 6” L x 6” W x 1/2” H Lags 1/4” x 1-1/2” lags. Eight (8) included. 3/8” hex drive )ODV L J DYDLODEOH L 0LOO D G FXVWRP FRORUV FDOO IRU GHWDLOV D G DYDLO DELOLW PL LPXP RUGHUV PD DSSO 0LOO FXVWRP ODFN RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSSTANCHION - ROOF ATTACHMENT CUT SHEET R-111Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT v102016 MADE IN USA MADE WITH RECYCLED MATERIAL © 2016 Zilla Corporation. All rights reserved. 77 Waneka Pkwy • Lafayette, CO 80026 • 720.880.6700 • fax 303.664.1268 • zillarac.com Zilla® So Simple It’s ScarySM 2 U P U SD DSSO KL SU XF L FOX L ZL K X OLPL D L 86 3D D U 6 / ;/ 6 / /. ;/ LOOD RXEOH WXG / )ODV L J Installation Instructions R WL XHG R H W SDJH DUWV L FOXGHG L W H DVVHPEO Base Plate XL Flashing XL Double Stud with S W G G 8 1/4” x 1-1/2” lags 2W HU UHTXLUHPH WV Drill/Driver to secure hardware 3/8” hex Drive socket to match fastening hardware 8VH W H IROORZL J L VWUXFWLR V WR L VWDOO W H LOOD RXEOH WXG / )ODV L J VVHPEO directly to sheathing or into structural members per system design speci cations. )ROORZ V L JOH PD XIDFWXUHU UHFRPPH GDWLR V D G - UHTXLUHPH WV IRU H SRVXUH D G SURSHU FRYHUDJH , VWDOODWLR WHSV WWDF W H DVH ODWH / ODFH Base Plate XL upon deck so installed Flashing is ≥ 3/4” beneath shingle course above in accordance with AHJ. :LW GUDZDO XOO 2XW DSDFLWLHV VVXPSWLR V Tabulated values above based on American Wood Council, NDS 2012 Table 10.3.1 and Table 11.2A Information for reference only. Engineer of Record shall be consulted for actual design. Thread penetration does not include roo ng thickness Wind Uplift Load Duration, 10 minutes: CD =1.6 Values listed above for dry (MC < 19%) lumber Rooftop Temperature Range, 125º F<T ≤150º F: Ct =0.7 Thread penetration into side grain of structural member /80 ( ( ,( ( ,), * ,7 / * (: Douglas Fir-Larch Douglas Fir-South Englemann Spruce-Lodgepole Pine Hem-Fir Hem-Fir (North) Southern Pine Spruce-Pine-Fir Spruce-Pine-Fir (South) Western Cedars OSB/Plywood WWDF the Base Plate with approved fasteners per AHJ or engineer of record. DO NOT OVERTIGHTEN FASTENERS! ,W LV W H L VWDOOHU V VROH UHVSR VLELOLW WR YHULI FRPSOLD FH RI W LV SURGXFW ZLW W H - SULRU WR L VWDOODWLR RI SURGXFW ≥ 3/4“ Sheathing attachment6W W WW W v102016 MADE IN USA MADE WITH RECYCLED MATERIAL © 2016 Zilla Corporation. All rights reserved. 77 Waneka Pkwy • Lafayette, CO 80026 • 720.880.6700 • fax 303.664.1268 • zillarac.com Zilla® So Simple It’s ScarySM 2 U P U SD DSSO KL SU XF L FOX L ZL K X OLPL D L 86 3D D U 6 / ;/ 6 / /. ;/ LOOD RXEOH WXG / )ODV L J Installation Instructions Continued 3 WWDF W H RXEOH WXG7 UHDG W H RXEOH WXG Z W W washer side down into the hole. Turn the Double Stud by hand to sandwich the Flashing between Base Plate and Double Stud (washer). 127( Once the Flashing is in rm contact with the Base Plate and washer, turn the Double Stud 1/4 turn to tighten. 2 127 2 ( 7,* 7(1 W Double Stud. R JUDWXODWLR V W Double Stud XL Flashing Assembly is now complete – So Simple It’s Scary!6 WWDF W H / )ODV L J DUHIXOO L VWDOO W H )ODV L J G the shingle course above with the required coverage. Follow shingle manufacturer recommendations and AHJ requirements for exposure and proper coverage. , VSHFW W H R HFWLR LVXDOO L VSHFW W H FR HFWLR Verify the Washer is properly seated and the reveal around the Gland Nut is even. , VWDOODWLR WHSV OLJ W H )ODV L J W W G G hole in the Base Plate. 2SWLR DO On the underside of the Flashing, apply a bead of caulk to the top and both sides of the Flashing prior to installation for added protection. Do not caulk the lower sloped edge of the Flashing.RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSSTANCHION - ROOF ATTACHMENT CUT SHEET R-112Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSDESCRIPTION: PART NUMBER(S): DRAWN BY: SNAPNRACK, ULTRA RAIL COMP KIT SEE BELOW mwatkins Solar Mounting Solutions THE INFORMATION IN THIS DRAWING IS CONFIDENTIAL AND PROPRIETARY. ANYREPRODUCTION, DISCLOSURE, OR USE THEREOF IS PROHIBITED WITHOUT THEWRITTEN CONSENT OF SUNRUN SOUTH LLC. 595 MARKET STREET, 29TH FLOOR ● SAN FRANCISCO, CA 94105 USAPHONE (415) 580-6900 ● FAX (415) 580-6902B REVISION: MATERIALS: DESIGN LOAD (LBS): ULTIMATE LOAD (LBS): TORQUE SPECIFICATION: CERTIFICATION: WEIGHT (LBS): 6000 SERIES ALUMINUM, STAINLESS STEEL, RUBBER 405 UP, 788 DOWN, 236 SIDE 2006 UP, 4000 DOWN, 1070 SIDE 12 LB-FT UL 2703, FILE E359313 0.80 PARTS LIST DESCRIPTIONPART NUMBERQTYITEM SNAPNRACK, UMBRELLA LAG, TYPE 3, 4IN, SS242-9226611 SNAPNRACK, ULTRA FOOT FOR U FLASHING, SILVER / BLACK242-01219, 242-0122012 SNAPNRACK, COMP FLASHING, 9IN X 12IN, SILVER / BLACK ALUM232-01375, 232-0137613 3 1 2 2 DESCRIPTION: PART NUMBER(S): DRAWN BY: SNAPNRACK, ULTRA RAIL COMP KIT SEE BELOW mwatkins Solar Mounting Solutions THE INFORMATION IN THIS DRAWING IS CONFIDENTIAL AND PROPRIETARY. ANYREPRODUCTION, DISCLOSURE, OR USE THEREOF IS PROHIBITED WITHOUT THEWRITTEN CONSENT OF SUNRUN SOUTH LLC. 595 MARKET STREET, 29TH FLOOR ● SAN FRANCISCO, CA 94105 USAPHONE (415) 580-6900 ● FAX (415) 580-6902B REVISION: ALL DIMENSIONS IN INCHES 11.75 3.25 8.75 .45 6.75 n1.00 4.20 .30 3.25 n1.00 1.00 SLOT 1.50 2.78 1.78 1.50 .38 .30 1.37 1.62 UMBRELLA L FOOT PROPERTIES SKU DESCRIPTION 242-01219 ULTRA RAIL UMBRELLA L FOOT, SILVER 242-01220 ULTRA RAIL UMBRELLA L FOOT, BLACK COMP FLASHING PROPERTIES SKU DESCRIPTION 232-01375 COMP FLASHING, 9" X 12", BLACK ALUM 232-01376 COMP FLASHING, 9" X 12", SILVER ALUM n.35 1.80 105° STANCHION - ROOF ATTACHMENT CUT SHEET R-113Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT pe.eaton.com General Duty Non-Fusible Safety Switch DG222URB UPC:782113144238 Dimensions: Height: 7.5 IN Length: 6.41 IN Width: 8.4 IN Weight:9 LB Notes:WARNING! Switch is not approved for service entrance unless a neutral kit is installed. Warranties: Eaton Selling Policy 25-000, one (1) year from the date of installation of the Product or eighteen (18) months from the date of shipment of the Product, whichever occurs first. Specifications: Type: General Duty/Non-Fusible Amperage Rating: 60A Enclosure: NEMA 3R Enclosure Material: Painted galvanized steel Fuse Configuration: Non-fusible Number Of Poles: Two-pole Number Of Wires: Two-wire Product Category: General Duty Safety Switch Voltage Rating: 240V Supporting documents: Eatons Volume 2-Commercial Distribution Eaton Specification Sheet - DG222URB Certifications: UL Listed Product compliance: No Data______________________________________________________________________ © 2016 Eaton. All rights reserved. V2-T1-26 Volume 2—Commercial Distribution CA08100003E—May 2018 www.eaton.com 1 1.1 Switching Devices Safety Switches All general-duty switches above 100A and all heavy-duty switches incorporate these K-Series switch design features. Two points of contact provide a positive open and close, easier operation, and also help prevent contact burning for longer contact life Visible Double-Break Rotary Blade Mechanism Protects against accidental contact with energized parts. Probe holes enable the user to test if the line side is energized without removing the shield. Not provided on general-duty switches, but available as a field kit or factory installed Clear Line Shield Clearly Visible Handle ●The position (ON or OFF) can be clearly seen from a distance and the length provides for easy operation Triple Padlocking Capability ●Personnel safety feature because the large hasp can accommodate up to three 3/8-inch (9.5 mm) shank locks Additional Locking Capability ●Cabinet door can be further padlocked at the top and bottom as applicable Interlocking Mechanism ●Door cannot be opened when the handle is in the ON position. Front and side operable defeater mechanism provides for user access when necessary on single- throw switches Tangential Knockouts ●An ample number are provided on the top, bottom and sides of both NEMA Types 1 and 3R enclosures through 200A Bolt-On Hub Kits ●For switches in a NEMA Type 3R, 30–200A. Use a Myers type hub for all others Standards and Certifications ●UL listed File No. E5239 ●Meets UL 98 for enclosed switches and NEMA Std. KS-1 Seismic Qualifications ●General-duty switches exceed the requirements of Uniform Building Code (UBC) and California Code Title 24 OSP-0011-10, OSP-0012-10 RELEASEREVDATE NAME ADDRESSAPNEQUIP. CUT SHEETS ADDRESS kW PHOTOVOLTAIC PLANSAC DISCONNECT CUT SHEET R-114Valley Solar21134A340 Riverside DrFlorence, MA 01062(413) 584-884412.540Neiman, Anna284 Riverside DrNorthampton, MA 0106208/06/2020SUBMIT FOR PERMIT