10810 - 2901Not For Construction10810 - 1
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
UniSpec II- Store Planning 072514
SECTION 10810 - TOILET ACCESSORIES
PART 1 - GENERAL
1.1 SUMMARY
A. Section Includes: Toilet accessories and attachment hardware, Owner furnished, Contractor installed.
B. Related Sections:
1. Section 01600 - Product Requirements: General procedures related to products.
2. Section 01640 - Owner Furnished Products: General procedures related to Owner furnished products.
3. Section 06100 - Rough Carpentry: Blocking for attachment of accessories.
1.2 REFERENCES
A. The publications below form a part of this specification to the extent referenced. Publications are referenced with-
in the text by the basic designation only.
B. American National Standards Institute (ANSI):
1. ANSI A117.1 – Accessible and Usable Buildings and Facilities.
1.3 DELIVERY, STORAGE AND HANDLING
A. Transport, handle, store, and protect products in compliance with the requirements of Section 01600.
B. Receive Owner Furnished products in accordance with the requirements of Section 01640.
C. Product Delivery: Owner’s Supplier will deliver products to site to be received by Contractor. Contact Owner’s
Supplier to coordinate product delivery and installation.
D. Acceptance at Site: Inspect products upon delivery to Site to verify quantity, and report discrepancies in quantity
delivered or damage.
E. Product Packaging: Products will be delivered in manufacturer's original packaging with identification markings
on each component or package.
PART 2 - PRODUCTS
2.1 OWNER FURNISHED PRODUCTS
A. Owner’s Supplier will furnish products as specified herein under provisions of Section 01640 for installation by
Contractor.
1. Owner’s Supplier (except soap dispensers and surface mounted paper towel dispensers): Haines, Jones &
Cadbury, Inc., Contact: Customer Service, (800) 459-7099, fax (479) 756-8998, Email:
WMT@hjcinc.com.
2. Owner’s Supplier (soap dispensers and surface mounted paper towel dispensers): Unspecified.
B. Descriptions and related provisions of products by Owner’s Supplier as specified herein are included as require-
ments for Supplier of products to be furnished by Owner and are included as information only to Contractor.
2.2 MANUFACTURERS
A. Provide products from the following manufacturers as specified in the Schedule of Accessories hereinafter:
1. American Specialties Co., Inc.; Yonkers, NY.
2. Bobrick Washroom Equipment, Inc.; North Hollywood, CA.
Not For Construction10810 - 2
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
3. Bradley Corporation, Menomonee, WI.
4. Brady Worldwide, Inc. Milwaukee, WI.
5. Dyson Inc. Chicago, IL. (National distributor: Haines, Jones & Cadbury, Inc. (800) 459-7099, Fax (479)
756-8998, Email: info@hjcinc.com)
6. Excel Dryer Corporation, East Longmeadow, MA.
7. Foundations Worldwide, Inc. (formerly Brocar Products Inc.), Medina, OH
8. Henkel Corporation, Rocky Hill, CT.
9. Koala Bear Kare Corporation (A Division of Bobrick). Englewood, CO.
10. Meek Manufacturing Company, Fort Smith, AR.
11. Saniflow Corp., Miami, FL, National distributor: Haines, Jones & Cadbury, Inc.
12. SourceOne, Fort Smith, AR, National distributor: Haines, Jones & Cadbury, Inc.
B. Substitutions: Comply with the requirements of Section 01600.
2.3 MATERIALS (OWNER FURNISHED, CONTRACTOR INSTALLED)
A. Stainless Steel: AISI Type 302/304.
B. Mounting Devices: Hot-dip galvanized after fabrication or of same material as accessory unit.
1. Grab Bar Hollow Wall Fasteners: GBW40 stainless steel commercial grab bar fasteners manufactured by
WingIts Innovations, LLC.
C. Adhesive: Epoxy type contact cement.
D. Finishes:
1. Chrome/Nickel Plating: Polished finish.
2. Stainless Steel: No. 4 satin finish, unless specified otherwise.
3. Shop Primed Ferrous Metals: Pre-treat and clean, spray apply one coat primer and bake.
2.4 FABRICATION
A. Weld and grind smooth joints of fabricated components.
B. Form exposed surfaces from one sheet of stock, free of joints. Form surfaces flat without distortion. Maintain flat
surfaces without scratches or dents.
C. Provide steel anchor plates and anchor components for installation on building finishes. Hot-dip galvanize ferrous
metal anchors and fastening devices.
D. Back paint components where contact is made with building finishes to prevent electrolysis.
E. Shop assemble components and package complete with anchors and fittings.
PART 3 - EXECUTION
3.1 PREPARATION
A. Deliver inserts and rough-in frames to jobsite at appropriate time for building-in. Use templates and rough-in
measurements as required.
B. Ensure that blocking is appropriately installed and ready to receive accessories.
C. Rough Wall Openings: Provide rough wall opening (RWO) in compliance with ADA Accessibility Guidelines, as
detailed on architectural drawings, and as described in the Schedule of Accessories.
3.2 INSTALLATION
Not For Construction10810 - 3
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
A. Install fixtures, accessories, and items in accordance with manufacturer's instructions and as shown on Drawings.
Install accessories within toilet rooms and install soap dispensers in other areas in addition to toilet rooms where
shown on the drawings. Use tamper-proof fasteners.
B. Install true, plumb, and level, securely and rigidly anchored to wall framing.
C. Where blocking or framing is not properly located to receive grab bars in existing hollow walls that are not modi-
fied or scheduled to receive new finishes, install grab bars using specified hollow wall fasteners. Install fasteners
in accordance with fastener manufacturer’s recommendations, using hole saw recommended by fastener manufac-
turer for type of wall construction and finish encountered.
D. Install sealant around metal frames of mirrors, and all toilet accessories abutting FRP/NRP wall panels.
3.3 SCHEDULE OF ACCESSORIES (OWNER FURNISHED, CONTRACTOR INSTALLED)
A. Soap Dispensers: Model as supplied by Owner.
B. Sanitary Napkin Dispenser:
1. Model No. 04684-25 by American Specialties, Inc.
a. Finish: Stainless Steel.
b. Rough Wall Opening: 16"W x 26"H x 4-1/4"D
2. Model No. 4017-10-45 by Bradley Corporation
a. Finish: Stainless Steel.
b. Rough Wall Opening: 12"W x 26"H x 4-1/2"D
C. Sanitary Napkin Disposal:
1. Model No. 0473-1A by American Specialties, Inc.
a. Finish: Stainless Steel.
2. Model No. 4722-15 by Bradley.
a. Finish: Stainless Steel.
D. Paper Towel Dispensers: Recessed Pull Core Paper Towel Cabinet and Waste Receptacle
1. Model 04693MCPTD, by American Specialties, Inc.
a. Rough Wall Opening: 15-3/4"W x 54-1/2"H x 10-1/4"D or 4-1/4"D depending on wall depth. Top
of rough wall opening 3/4" below top of unit.
b. Provide collar as required for depth of wall stud.
2. Model No. 236-WM as manufactured by Bradley.
a. Rough Wall Opening: 15-3/4"W x 54-1/2"H x 7-1/2"D.
b. Provide collar as required for depth of wall studs.
E. Paper Towel Dispensers - Surface Mounted: Model as supplied by Owner.
F. Toilet Paper Dispenser:
1. Model No. 5425-0000, by Bradley Corporation.
2. Model No. 0039 by American Specialties.
3. Non-Public Toilets: Stainless steel, surface mounted, automatic (no-touch) model. One of the following:
a. Model MO6ACS-UL Speedflow by Saniflow.
b. Model 2902-287400 Aerix by Bradley.
G. Electric Hand Dryers: Stainless steel, surface mounted, automatic (no-touch) model. One of the following:
1. Model MO6ACS-UL Speedflow by Saniflow.
2. Model 2902-287400 Aerix by Bradley.]
H. Diaper Changing Table and Accessories:
1. Changing Table: Stainless steel, recessed mount. Provide one of the following
a. Model 100-SSC-MCB, by Foundations Worldwide, Inc.
b. Model KB110-NLRF, by Koala Kare Products.
Not For Construction10810 - 4
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
2. Accessories:
a. Manufacturer: Koala Kare Products.
1) Diaper Dispenser: Model KB143-SS-Recessed with KB144-99 collar.
a) Rough Wall Opening: 12 1/2”W x 42 1/4 ”H x 5 1/2 ”D.
2) Sanitary Liner Dispenser: Model KB134-SSLD-Recessed.
a) Rough Wall Opening: 7 7/8”W x 16 1/2 ”H x 4 1/4 ”D.
b. Manufacturer:Foundations Worldwide, Inc.
1) Diaper Dispenser: Model 105-SS-SM-Recessed with 025-SS recessing flange.
a) Rough Wall Opening: 12-3/4"W x 42-1/4"H x 5-1/4"D.
c. Manufacturer: Bradley Corp.
1) Sanitary Liner Dispenser: Model 2441-Recessed.
a) Rough Wall Opening: 11-3/8"W x 15-11/16" H x 4"D.
I. Toilet Seat Cover Dispensers: Surface mounted (one per each water closet), 22 gage 18-8 type 304 stainless steel,
satin finish.
1. Model No. 0477SM, by American Specialties.
2. Model No. B221, by Bobrick.
3. Model No. 5831, by Bradley.
J. Small Framed Mirrors: No. 1 quality 1/4 inch float glass electrolytically copper plated, tempered glass. Mitered
stainless steel frame; concealed theft resistant wall hanger. Mirror size shall be 24 x 36 unless otherwise shown.
1. Model No. M1516, by Meek.
2. Model No. 781-024362, by Bradley.
K. Child Safety Seat: Surface Mounted.
1. Model No. 103-BQS, by Foundations Worldwide, Inc.
2. Model No. KB-102, by Koala Kare Products.
L. Grab Bars: 18 gage stainless steel; 1-1/4 inch diameter, (1-1/2 inch diameter where required by Local Code) tex-
tured grip surface; concealed mounting consisting of welded-on mounting flange with snap-on cover flange or es-
cutcheon. Location, quantity, and length shall be as shown.
1. Model No. 3700 P, by American Specialties.
2. Model No. B5506.99, by Bobrick.
3. Model No. 832-2, by Bradley.
3.4 CLEANING
A. Protection and Cleaning of Toilet Accessories and Attachment Hardware Prior to Possession.
1. Immediately prior to possession, clean stainless steel accessories and attachment hardware thoroughly us-
ing soap, ammonia, or mild detergent and water. Apply with sponge or soft cloth, rinse with clear water
and wipe dry. Always rub in the direction of polish lines. Rinse thoroughly with fresh water after every
cleaning operation. Clean and polish to a spotless luster. Wipe dry to avoid water marks.
2. Clean and polish stainless steel accessories and mirror surfaces to a spotless luster.
END OF SECTION