09900 - 2901Not For Construction09900-1
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
UniSpec II - Store Planning 013015
SECTION 09900 - PAINTS AND COATINGS
PART 1 - GENERAL
1.1 SUMMARY
A. Section Includes:
1. Field applied paints and finishes for interior and exterior surfaces. (Partial Wal-Mart Furnished/Partial Con-
tractor furnished, Contractor Installed)
B. Related Sections:
1. Section 01640 - Owner Furnished Products.
2. Section 01742 - Construction and Demolition Waste Management and Disposal.
3. Section 01743 – Hazardous/Universal Waste Management and Disposal.
4. Section 05120 - Structural Steel: Shop priming.
5. Section 05500 - Metal fabrications: Shop priming.
6. Section 07240 – Exterior Insulation and Finish System (EIFS)
7. Section 08110 - Steel Doors and Frames: Shop priming.
8. Section 09250 - Gypsum Board: Textured Coatings.
1.2 REFERENCES
A. The publications listed below form a part of this specification to the extent referenced. Publications are referenced
within the text by the basic designation only.
B. ASTM International (ASTM):
1. ASTM E 2129 - Standard Practice for Data Collection for Sustainability Assessment of Building Products.
1.3 ADMINISTRATIVE REQUIREMENTS
A. Scheduling and Coordination: Complete painting work at locations indicated to receive exterior building signage
prior to new signage installation or reinstallation of existing signage previously removed and salvaged.
1.4 SUBMITTALS
A. Applicator Qualifications Statement: Submit statement of applicator qualifications in accordance with Section
01330. Submit within 30 days of contract award.
1.5 QUALITY ASSURANCE
A. Regulatory Requirements:
1. VOC Content: Provide paint and coating materials that conform to Federal, State, and Local restrictions for
Volatile Organic Compounds (VOC) content.
2. Toxicity/EQ: Comply with federal, state, and local toxicity and environmental quality regulations and with
federal requirements on content of lead, mercury, and heavy metals. Do not use solvents in paint products
that contribute to air pollution.
B. Exterior Finish Pre-Installation Conference:
1. Convene a pre-installation teleconference, at least one week prior to commencing Work of this Section and
prior to the Elastomeric Coating Pre-Installation Conference, if specified.
2. Contact Wal-Mart Construction Manager two weeks prior to pre-installation conference to confirm sched-
ule.
3. Attendance:
a. Wal-Mart Construction Manager.
b. Contractor.
Not For Construction09900-2
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
c. Coating Subcontractor.
d. Coating Manufacturer's Technical Representative. This individual must be the same person that
performed the Initial Site Visit. Technical Representative shall reference the Sherwin Wil-
liams/WM Initial Site Visit Worksheet for site specific information.
1) Contact Name: DAN PIOTROWSKI, CELL: 413.231.2047
2) Supplier Store Number: 5654
3) Store Address: 312 KING ST, NORTHAMPTON, MA 01060
4) Store Phone number: 413.584.8789
4. Agenda:
a. Sherwin Williams/WM Initial Site Visit Worksheet.
b. Recommended exterior paint/coating and primer (if required).
c. Preparation of existing substrate to receive recommended finish.
d. Sequence and method of application of coating system.
e. Warranty provisions.
5. Record, type, and print minutes of the meeting. Distribute minutes to all parties concerned within 5 days of
the meeting. Transmit one copy of the minutes to the Owner's representative for information purposes.
1.6 DELIVERY, STORAGE AND HANDLING
A. Transport, handle, store, and protect products in compliance with the requirements of Section 01600.
B. Product Order and Delivery: The Contractor shall prepare and order all coating materials and accessories for Con-
tractor furnished products and arrange delivery of Wal-Mart furnished products and submit together to Wal-Mart
Supplier specified herein. Wal-Mart Supplier will deliver products to site on delivery date established by Contrac-
tor. To arrange product order and delivery, contact Supplier.
C. Acceptance at Site: Receive products as specified in Section 01640.
1. Verify quantity of products furnished with Bill of Material provided with Wal-Mart furnished products.
2. Report discrepancies in product quantity delivered or damage to Supplier.
3. Upon notification by Contractor, Supplier will arrange for delivery of replacement products.
4. Note description of product quantity discrepancies and/or product damage on Bill of Materials.
D. Paint orders shall identify the store number, location, and address of project.
E. Delivery of paint materials shall be in sealed original labeled containers, bearing manufacturer's name, type of
paint, brand name, lot number, brand code, coverage, surface preparation, drying time, cleanup requirements, color
designation, and instructions for mixing and/or reducing. Notify Supplier when delivered products to not conform
to these requirements.
1.7 ENVIRONMENTAL REQUIREMENTS
A. Apply paint finishes only when moisture content of surfaces is within manufacturer's acceptable ranges for type of
finish being applied.
B. Minimum surface temperatures or ambient air temperature shall be as follows for the specified coatings unless oth-
erwise specifically stated by the manufacturer for the specific coating:
1. Alkyd and interior and exterior latex finishes: 50 degrees F.
2. Varnish and transparent finishes: 65 degrees F.
3. All coatings: 5 degrees F above dew point.
C. Provide continuous ventilation and heating facilities to maintain temperatures above the manufacturer’s stated
minimum surface and air temperature for 24 hours prior to, during, and 48 hours after application of finishes.
D. Do not apply paint in areas where dust is being generated.
E. Provide lighting level in areas being painted of 80 foot candles measured mid-height at substrate surface.
Not For Construction09900-3
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
F. Waste Management:
1. Comply with requirements of Sections 01742 and 01743.
2. Obtain paint in containers of the largest size practical for each color, sheen, and type.
3. Remove excess paint from containers and dispose in accordance with MSDS data and local environmental
regulations for paint products.
4. Expose waste paint to air and allow paint to dry.
5. Return reusable containers to manufacturer.
6. Clean and recycle containers that cannot be returned to manufacturer.
PART 2 - PRODUCTS
2.1 OWNER FURNISHED PRODUCTS
A. Products Supplied by Wal-Mart Supplier and Installed by Contactor: Under provisions of Section 01640, Wal-
Mart’s supplier will furnish a limited portion of the specified products in the quantities as specified hereinafter on
the Wal-Mart furnished Quantity Schedule for installation by the Contractor.
1. Wal-Mart supplied products will conform to the specifications included in this section.
1) Wal-Mart Supplier: Sherwin Williams Company. Contact: Kevin Behm, (216) 566-1558,
Kevin.c.behm@sherwin.com Contact Name: DAN PIOTROWSKI, CELL: 413.231.2047
2) Supplier Store Number: 5654
3) Store Address: 312 KING ST, NORTHAMPTON, MA 01060
4) Store Phone number: 413.584.8789
B. Products Provided (Furnished and Installed) by the Contractor: The Contractor shall provide all products specified
herein which are not scheduled to be Wal-Mart furnished.
C. Quantity Furnished: Wal-Mart will furnish coatings in the quantities shown on the Wal-Mart Furnished Quantity
Schedule at the end of this Section. The quantity furnished by Wal-Mart is not to be considered fully sufficient for
the total project. Supplemental required quantities to those of Wal-Mart furnished coatings including additional
quantities of Wal-Mart furnished coatings, coatings not furnished by Wal-Mart, and other materials and accesso-
ries as determined by the Contractor necessary for the complete project, shall be furnished by the Contractor at
Contractor expense. Supplemental coating quantities shall be obtained from the Wal-Mart Supplier. Wal-Mart
furnished coatings are not differentiated by color. The Contractor shall identify on the order, the appropriate col-
ors as required.
2.2 MATERIALS
A. Paint: Wal-Mart and Contractor provided coating materials shall be the product of Sherwin Williams Co. as speci-
fied in the Painting Schedule hereinafter. Substitutions will not be permitted.
B. Accessory Materials (Contractor Provided): Accessory materials not specifically indicated herein but required to
achieve the finishes specified, shall be provided by the Contractor and shall be of highest quality and as recom-
mended by the manufacturer.
1. Paint Thinners: Type recommended by paint or coating manufacturer for paint or coating system, VOC
compliant, first line commercial quality. Do not use solvents for thinning paint materials.
2. Patching Materials: Low VOC Latex filler.
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine surfaces and adjacent areas where products will be applied and verify that surfaces conform to product
manufacturer's requirements for substrate conditions. Do not proceed until unsatisfactory conditions have been cor-
rected.
B. Beginning of application indicates acceptance of substrate conditions.
Not For Construction09900-4
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
3.2 PREPARATION
A. Apply paint only on surfaces free of dirt, rust, scale, grease, moisture, scuffed surfaces, and conditions otherwise
detrimental to formation of a durable paint film.
B. Coordinate moving of merchandise and fixtures with the Wal-Mart Field Project Manager prior to painting in Sales
areas.
C. Perform preparation and cleaning procedures in accordance with paint manufacturer's published instructions for
each particular substrate condition.
1. Provide barrier coats over incompatible primers or remove and reprime as required.
2. Remove hardware, hardware accessories, machined surfaces, plates, lighting fixtures, and similar items in
place and not to be painted. Reinstall all removed items after completion of paint work.
3. Clean surfaces to be painted before applying paint or surface treatment. Remove oil and grease prior to me-
chanical cleaning.
D. Ferrous Metals: Clean ferrous surfaces that are not galvanized or shop-coated, of oil, grease, dirt, loose mill scale,
and other foreign substances by solvent or mechanical cleaning.
1. Touch-up shop-applied prime coats where damaged or bare. Clean and touch-up with same type shop pri-
mer.
E. Galvanized Surfaces: Clean free of oil and surface contaminants with non-petroleum based solvent. Apply coat of
etching primer if required by paint manufacturer.
F. Cementitious Materials: Prepare cementitious surfaces to be painted by removing efflorescence, chalk, dust, dirt,
grease, oils, and by roughening as required to remove glaze.
1. Determine alkalinity and moisture content of surfaces to be painted by performing appropriate tests.
a. Alkalinity shall be a maximum ph of 13 and a minimum of 6.
b. If surface alkalinity is outside range specified above, correct condition before application of paint.
c. Do not paint over surfaces where moisture content exceeds that permitted in manufacturer's printed
instructions.
2. Clean and etch floor surfaces scheduled to be painted with a commercial solution of muriatic acid, or other
etching cleaner. Flush floor with clean water to neutralize acid and allow to dry before painting. Mask floor
surfaces not to be cleaned and etched.
a. Sealer Removal: Prior to etching, remove curing compound and sealers with strong solvents such as
xylene, MEK, toluene or commercial paint strippers or by sandblasting or other similar mechanical
action.
G. Wood: Clean wood surfaces to be painted of dirt, oil, and other foreign substances with scrapers, mineral spirits,
and sandpaper, as required. Sandpaper smooth those finished surfaces exposed to view, and dust off. Scrape and
clean small, dry, seasoned knots and apply a thin coat of white shellac or other recommended knot sealer, before
application of priming coat. After priming, fill holes and imperfections in finish surfaces with putty or plastic
wood filler. Sandpaper smooth when dried.
1. Prime, stain, or seal wood required to be job-painted immediately upon delivery to job. Prime edges, ends
faces, undersides, and backsides of such wood, including cabinets and counters.
2. Seal tops, bottoms, and cut-outs with a heavy coat of varnish or equivalent sealer immediately upon deliv-
ery to job.
H. Gypsum Board: Fill minor defects with filler compound. Spot prime defects after repair.
1. If shown on Drawings to receive textured finish, prepare gypsum board surfaces with textured coating
specified in Section 09250.
2. Exterior Gypsum Board Sheathing: Exterior gypsum board sheathing to receive a paint finish shall be pre-
pared for painting with joint treatment and skim coating as specified in Section 09250.
I. Previously Painted Surfaces: Prepare previously painted surfaces in accordance with manufacturer’s recommenda-
tions. Remove loose paint by scrape or wire brush as necessary. Smooth edges of existing sound paint film to pre-
vent telegraphing of ridges through new paint film. Clean surfaces thoroughly and roughen existing paint surfaces
Not For Construction09900-5
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
by lightly sanding. Clean and remove mildew using trisodium phosphate. Touch up bare surfaces with prime coat
scheduled. Painted surfaces with existing sound prime or finish coats do not require additional prime coating. Fin-
ish coats shall be applied in number and DFT specified.
3.3 APPLICATION
A. Apply coating systems specified in the Painting Schedule hereinafter for the corresponding surface. Shop primed
surfaces will not require field applied 1st coat (primer) specified in the Painting Schedule.
B. Apply paint products in accordance with manufacturer's published instructions using application procedures ap-
proved for the particular application and substrate.
C. Apply each coat to the Dry Film Thickness (DFT) specified which represents the minimum Dry Film Thickness in
mils per coat. Apply each coat to uniform coverage.
D. Apply each coat slightly darker than preceding coat unless otherwise approved by Wal-Mart Construction Manag-
er. Lightly sand surfaces between coats to achieve specified finish.
E. Allow drying time between coats as recommended by the manufacturer.
F. Apply additional coats when undercoats, stains, or other conditions show through final coat until paint film is of
uniform finish, color, and appearance. Surfaces, including edges, corners, crevices, welds, and exposed fasteners
shall receive minimum dry film thickness equivalent to that of flat surfaces.
G. Do not paint sealants in exterior building wall control or expansion joints. Paint wall prior to sealant application in
building joints. Protect joints to be sealed by inserting calking backer rods at face of wall.
H. Block Fillers: Apply block fillers to concrete masonry units at rate to provide complete coverage with pores filled.
I. Prime Coats: Before application of finish coats, apply a prime coat of material as scheduled or as recommended
by manufacturer to material scheduled to be painted or finished that has not been shop primed. Recoat primed and
sealed surfaces where evidence of suction spots or unsealed areas in first coat appears, to assure a finish coat with
no burn through or other defects due to insufficient sealing.
J. Pigmented (Opaque) Finishes: Completely cover to provide an opaque, smooth surface of uniform finish, color,
appearance and coverage. Cloudiness, spotting, laps, brush marks, runs, sags or other surface imperfections will
not be acceptable.
3.4 MECHANICAL AND ELECTRICAL EQUIPMENT
A. Replace identification markings on mechanical or electrical equipment when painted over or spattered.
B. Where exposed piping, conduit, and electrical equipment are to be painted, paint color and texture shall match ad-
jacent surfaces.
C. Paint both sides and edges of plywood backboards for electrical equipment prior to installation.
D. Prepaint Gas piping prior to installation. Touch up paint after installation. Colors shall be as follows:
1. Exterior Piping on Roof (Yellow): P5, OSHA Standard "Safety Yellow."
2. Piping in all Other Areas: Color to match adjacent surfaces.
3.5 FIELD QUALITY CONTROL
A. Inspect painting and coating application for scheduled material, color, sheen, specified thickness (DFT), and cov-
erage.
B. Remove, refinish or repaint work rejected by Wal-Mart Construction Manager.
Not For Construction09900-6
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
3.6 CLEANING
A. As work proceeds and upon completion, promptly remove paint where spilled, splashed, or spattered.
B. During progress of work keep premises free from unnecessary accumulation of tools, equipment, surplus materials,
and debris.
C. Collect waste, cloths, and material which may constitute a fire hazard, place in closed metal containers, and re-
move daily from site.
D. Upon completion of work, leave premises neat and clean.
3.7 PROTECTION
A. Protect other surfaces from paint and damage. Repair damage as a result of inadequate or unsuitable protection.
3.8 PAINT COLOR SCHEDULE
A. Provide following colors as applicable as shown or scheduled on the drawings.
Mark Color Number/Name by Sherwin Wil-
liams unless otherwise noted.
P1 SW # 1234 "Evening Shadow"
P2 SW # 7664 "Steely Gray"
P3 SW # 1504 “Nobility Blue”, OR
SW # 6510 “Loyal Blue”
P4 SW # 1602 “Theater Red”
P5 OSHA Standard "Safety Yellow"
P6 SW # 6811 "Honorable Blue"
P7 Pittsburgh Paints #2537 "Blossom
White"
P8 SW # 7005 “Pure White”
P9 SW # 7042 “Shoji White”. Apply over
textured coating specified in Section
09250
P10 SW # 6061 “Tan Bark”
P11 SW # 6115 “Totally Tan”
P12 SW # 6112 “Biscuit”
P13 SW # 6454 “Shamrock"
P14 SW # 6677 “Goldenrod”
P15 SW #7669 “Summit Gray”
P16 SW # 7074 “Software”
P17 SW # 7689 “Row House Tan”
P18 SW # 7068 “Grizzle Gray”
P19 SW # 6094 "Sensational Sand"
P20 SW # 7036 “Accessible Beige”
P21 Sherwin Williams “Safety Red”. Shop
coated doors and storefronts shall be
coated with color P21 specified in the
respective Division 8 sections.
P22 Pantone Color System PMS 286C.
P23 SW #7005 “Pure White."
P24 SW # 2819 “Downing Slate”
P25 SW # 0045 “Antiquarian Brown”
P26 SW # 6080 “Utterly Beige”
P27 SW # 6103 "Tea Chest"
P28 SW # 6124 "Cardboard"
Mark Color Number/Name by Sherwin Wil-
liams unless otherwise noted.
P29 SW # 6420 Queen Anne’s Lace"
P30 SW # 2018 "Pink Beige"
P31 SW # 2016 "Canberra".
P32 SW # 6387 "Compatible Cream"
P33 SW # 6385 "Dover White"
P34 SW # 6519” Hinting Blue.
P35 SW # 7071 “Gray Screen”
P36 SW # 6989 "Domino"
P37 SW # 0046 "White Hyacinth"
P38 SW #6102 "Portabello"
P39 SW #6122 "Camelback"
P40 SW # 6665 “Gardenia”
P41 SW # 6100 “Practical Beige”
P42 SW # 6372 “Inviting Ivory”
P43 SW # 6667 “Afterglow”
P44 SW # 6666 “Enjoyable Yellow”
P45 SW # 0044 “Hubbard Squash”
P46 SW # 7006 “Extra White”
P47 SW # 0051 “Classic Ivory”
P48 SW # 7722 “Travertine"
P49 SW #7019 “Gauntlet Grey”
P50 SW #6382 “Ceremonial Gold”
P51 SW # 6662 “Summer Day”
P52 SW # 6334 “Flower Pot”
P53 SW # 6810 “Lupine”
P54 SW # 6432 “Garden Spot”
P55 SW # 6285 “Grape Harvest”
P56 SW # 6500 “Open Seas”
P57 SW # 2848 “Roycroft Pewter”
P58 Not Used
P59 SW # 0077 “Classic French Gray”
P60 SW # 6053 “Reddened Earth”
P61 SW # 6079 “Diverse Beige”
P62 SW # 6172 “Hardware”.
P63 SW # 2340 “Buff”
Not For Construction09900-7
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
Mark Color Number/Name by Sherwin Wil-
liams unless otherwise noted.
P64 SW # 6332 “Coral Island”
P65 SW # 6378 “Crisp Linen”
P66 SW # 6085 “Simplify Beige”
P67 SW # 6114 “Bagel”
P68 SW # 6113 “Interactive Cream”
P69 SW # 6340 “Baked Clay”.
P70 SW # 2838 “Polished Mahogany”
P71 SW # 7051 “Analytical Gray”.
P72 SW # 6658 “Welcome White”.
P73 SW # 6214 “Underseas”
P74 SW # 6659 “Captivating Cream”
P75 SW # 2804 “Renwick Rose Beige”
P76 SW #076 Medium Wal-Mart Blue
P77 SW # 6087 “Trusty Tan”
P78 SW # 2445 “Creamy White”
P79 SW # 6359 “Sociable”
P80 SW # 6060 “Moroccan Brown”
P81 SW #6258 “Tricorn Black”
P82 SW # 7679 "Golden Gate"
P83 SW # 6082 "Cobble Brown"
P84 Not Used
P85 SW # 7519 "Mexican Sand"
P86 SW # 7687 "August Moon"
P87 SW # 2807 "Rookwood Medium
Brown"
P88 SW # 2823 "Rookwood Clay"
P89 SW # 6062 "Rugged Brown "
P90 SW # 7502 "Dry Dock"
P91 SW # 7513 "Sanderling"
P92 SW # 7536 "Bittersweet Stem"
P93 SW # 7538 "Tamarind"
P94 SW # 7694(EXT) "Exterior Dromedary
Mark Color Number/Name by Sherwin Wil-
liams unless otherwise noted.
Camel"
P95 SW # 7702 "Spiced Cider"
P96 SW # 7705 "Wheat Penny "
P97 SW # 7710 "Brandy Wine"
P98 SW # 7718 "Oak Creek"
P99 SW # 7722 "Travertine"
P100 SW #6521 “Notable Hue”
P101 SW #6904 “Gusto Gold”
P102 SW #7518 “Beach House”
P103 SW #6095 “Toasty”
P104 SW #6676 “Butterfield”
P105 SW #6526 “Icelandic”
P106 SW #6675 “Afternoon”
P107 SW#7698 “Straw Harvest”
P113 SW #6674 “Jonquil”
P114 SW #7720 “Deer Valley”
P115 SW #6076 “Turkish Coffee”
P124 SW #7522 “Meadowlark”
P125 SW #6923 “Festival Green”
P126 SW #6885 “Knockout Orange”
P127 SW #7719 “Fresco Cream”
P128 SW #7510 “Chateau Brown”
P150 SW #6354 “Armagnac”
P152 Pantone 368C (WNM Brand Green)
P153 PMS 284 (Blue)
P154 PMS 364 (Green)
P155 SW #6661 “Papaya”
P156 SW #7717 “Ligonier Tan”
P157 SW #7732 “Lemongrass”
P158 SW #7725 “Yearling”
3.9 PAINT SHEEN SCHEDULE
A. Gloss:
1. Exterior metal surfaces.
2. Exterior hollow metal doors and frames (inside and outside surfaces).
3. Roof hatch (inside and outside surfaces).
4. Interior & exterior pipe bollards shown to be painted.
5. Interior & exterior metal railings.
6. Metal stair stringers and handrails.
7. Metal fixed ladders and cages.
8. Exterior composite overhead sectional door surface if shown to be painted.
B. Semi-gloss:
1. Interior hollow metal doors and frames.
2. Interior hollow metal window frames.
3. Wood trim or simulated wood trim scheduled to be painted.
4. Coiling metal counter doors, except aluminum coiling counter shutters at Pharmacy.
5. Toilet gypsum board ceilings.
6. All walls within Pharmacy and exterior face of Pharmacy front wall (sales floor side).
7. Interior columns surfaces to receive epoxy finish.
Not For Construction09900-8
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
C. Eggshell:
1. All surfaces to be painted where sheen is not otherwise specified.
D. Flat:
1. Exterior Insulation and Finish System.
2. Exterior gypsum board ceilings.
3.10 ITEMS TO BE PAINTED SCHEDULE
A. Paint surfaces as shown or scheduled on the drawings including, but not limited to, the following items.
1. Exterior: Paint existing exterior surfaces and new exterior surfaces as shown and noted on the Drawings,
including, but not limited to:
a. Hollow metal doors and frames.
b. Metal opening frames and trim.
c. Metal flashing and downspout (surfaces exposed from ground level).
d. Metal gutters (surfaces exposed to view from ground level).
e. Metal fascias (vertical face).
f. Top of metal parapet cap where exposed to view from ground level.
g. Parapet walls, roof side (where roofing does not occur).
h. Pipe bollards where shown to be painted.
i. Metal railings.
j. Roof hatch.
k. Shop primed metal canopies and canopy supporting steel structure.
l. Overhead doors if shown.
m. Concrete masonry unit.
n. Paving graphics and markings.
o. Exposed piping and conduit, hangers and supports.
2. Interior: Paint existing and new interior surfaces as indicated on the Drawings including, but not limited to:
a. Hollow metal doors and frames.
b. Hollow metal window frames.
c. Overhead coiling doors.
d. Metal opening frames and trim.
e. Gypsum wallboard.
f. Exposed concrete unit masonry.
g. Pipe Bollards shown to be painted.
h. Metal railings.
i. Exposed plywood.
j. Plywood wainscot, if shown to be painted.
k. Exposed mechanical ductwork, hangers and supports (if scheduled to be painted).
l. Exposed piping and conduit, hangers and supports (where exposed to Customer view if exposed
structure is painted).
m. Exposed fire protection piping, hangers and supports (where exposed to Customer view if exposed
structure is painted).
n. Exposed overhead structure including joists, girders, bridging, miscellaneous metal fabrications and
deck (if scheduled to be painted).
o. Exposed structure columns.
p. Floor striping, graphics, and markings as shown or noted.
q. Metal stair stringers and handrails.
r. Exposed wood trim.
B. Do not paint the following Items:
1. Aluminum, brass, bronze, stainless steel, and chrome plated steel.
2. Pre-finished items, such as toilet compartments, acoustical ceiling materials, mechanical, and electrical
equipment or factory finished metal panels and trim, unless otherwise shown or specified.
3. UL, FM, and other code-required labels.
4. Equipment identification, performance rating, and name plates.
5. Finish hardware.
Not For Construction09900-9
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
6. Fire Suppression sprinklers.
3.11 PAINTING SCHEDULE
A. Apply paint to the substrate surface scheduled as applicable as specified or as shown on the drawings in accord-
ance with the following:
Surface Sheen 1st Coat DFT
(mils)
VO
C
(g/l)
2nd and 3rd Coats DFT
(mils)
VOC
(g/l)
EXTERIOR PAINTING SCHEDULE
Ferrous
Metal
Gloss Pro Industrial ProCryl Universal
Primer B66-310
3.0 100 2 Coats: Pro Industrial Zero VOC
Enamel, B66-600 Series
4.0 0
Ferrous
Metal
(Existing
roof
mounted
equip fram-
ing to re-
main)
Gloss All States except CA: Epolon II
Rust Inhibitive Epoxy Primer
B67W400, B67A400, B67A400
State of CA: Macropoxy 646-
100, B58W620, B58V620
5.0
5-10
300
<100
2 Coats: WB Acrolon 100 Water
Based Urethane B65-720, B65V720
2-4 <100
Prefinished
Metal Pan-
els and
Trim
(If shown
to be re-
painted)
Low
Sheen
Bond-Plex Waterbased Acrylic
B71-200 Series 4.0 48 1 Coat: Bond-Plex Waterbased
Acrylic B71-200 Series 4.0 48
Galvanized
Trim
Semi-
gloss
Pro Industrial ProCryl Universal
Primer B66-310 3.0 100 2 Coats: Pro Industrial Zero VOC
Enamel, B66-600 Series
4.0 0
Nonferrous
and Galva-
nized Met-
al, includ-
ing existing
ornamental
metal fenc-
ing (if
shown to be
repainted)
Semi-
gloss
Pro Industrial ProCryl Universal
Primer B66-310 3.0 100 2 Coats: Pro Industrial Zero VOC
Enamel, B66-600 Series
4.0 0
Concrete
Masonry
Unit
New Con-
struction
Elastomer-
ic (50 de-
grees F or
above)
Flat Heavy Duty Block Filler B42W46 18.0 100 2 Coats: Conflex XL High Build
Elastomeric, A5-400
6-7.5 97
Concrete
Masonry
Unit
New Con-
struction
Elasto-
meric (Be-
low 50 de-
Flat Loxon Block Surfacer, A24W200
(Above 35°F).
8.0 81 2 Coats: UltraCrete Solvent Borne
Masonry Coating, B46 Series
(Above 20° F)
6-8 400
Not For Construction09900-10
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
Surface Sheen 1st Coat DFT
(mils)
VO
C
(g/l)
2nd and 3rd Coats DFT
(mils)
VOC
(g/l)
grees F)
Concrete
Masonry
Unit
Existing
Construc-
tion
Elastomer-
ic (50 de-
grees F or
above)
Flat
Concrete
Masonry
Unit
Existing
Construc-
tion
Elasto-
meric (Be-
low 50 de-
grees F)
Flat
Concrete
Masonry
Unit
Existing
Construc-
tion
Acrylic
Flat Loxon Block Surfacer, A24W200
(For touch up after power
washing).
Apply surfacer as recom-
mended by paint manufacturer
8.0 81 1 Coat: A-100 Exterior Latex Finish,
A6-100 Series
1.3 49
Exterior
Insulation
and Finish
System
Flat A-100 Exterior Latex Finish, A6-
100 Series 1.3 49 1 Coat: A-100 Exterior Latex Finish,
A6-100 Series
1.3 49
Fiber Ce-
ment Sid-
ing
Flat Loxon Concrete and Masonry
Primer, B28W8300
3.2 96 2 Coats: A-100 Exterior Latex Fin-
ish, A6-100 Series 1.3 49
Exposed
Timber,
Purlins,
Plywood,
Wood
Semi-
Trans
parant
Stain
WoodScapes Polyurethane Stain
A15T5 1.3 79 1 Coat: WoodScapes Polyurethane
Stain A15T5
1.3 79
Exposed
Timber,
Purlins,
Plywood,
Wood
Opaq
ue
Stain
1 Coat: WoodScapes Latex Stain
A15W51
1.3-
2.6
<100 1 Coat: WoodScapes Latex Stain
A15W51
1.3-
2.6
<100
Gypsum
Board
(Ceiling)
Flat A-100 Exterior Latex Primer,
B42W43 1.4 87 2 Coats: A-100 Exterior Latex Fin-
ish, A6-100 Series
1.3 49
Concrete
Pavement
Egg-
shell
Setfast Acrylic Waterborne Traf-
fic Marking Paint, TM 226/227 8.5 100 1 Coat: Setfast Acrylic Waterborne
Traffic Marking Paint, TM 226/227
8.5 100
INTERIOR PAINTING SCHEDULE
Surface Sheen 1st Coat DFT
(mils)
VO
C 2nd and 3rd Coats DFT
(mils)
VOC
(g/l)
Not For Construction09900-11
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
Surface Sheen 1st Coat DFT
(mils)
VO
C
(g/l)
2nd and 3rd Coats DFT
(mils)
VOC
(g/l)
(g/l)
Ferrous
Metal
(Except as
otherwise
scheduled)
Gloss Pro Industrial ProCryl Universal
Primer B66-310
2 100 All States except CA:
2 Coats: Pro Mar 200 Interior Latex
Gloss Enamel, B21W200
State of CA:
2 Coats: Solo Gloss Low VOC
Enamel, B21WJ Series
1.5
1.6
143
49
Ferrous
Metal
(Except as
otherwise
specified)
Semi-
gloss
ProCryl Universal Primer B66-
310 2 100 2 coats: ProMar 200 Zero VOC Inte-
rior Latex Semi-Gloss Enamel, B31-
2600 Series
1.6 0
Ferrous
Metal
(Columns
and Hollow
Metal Door
Frames as
shown on
Drawings
to receive
epoxy)
Semi-
gloss
All States except CA: Epolon II
Rust Inhibitive Epoxy Primer
B67W400, B67A400, B67A400
State of CA: Macropoxy 646-
100, B58W620, B58V620
4.0
5.0-
10.0
300
100
1 coat: WB Acrolon 100 Water
Based Urethane B65-720,
B65V720
2-4 <100
Galvanized
Metal
(Exposed
Ductwork)
Semi-
gloss
Pro Industrial ProCryl Universal
Primer B66-310 2 100 2 coats: ProMar 200 Zero VOC Inte-
rior Latex Semi-Gloss Enamel, B31-
2600 Series
1.6 0
Concrete
Masonry
Unit (New
Construc-
tion)
Gloss Loxon Concrete and Masonry
Primer, B28W8300 8.0 45 All States except CA:
2 Coats: Pro Mar 200 Interior Latex
Gloss Enamel, B21W200
State of CA:
2 Coats: Solo Gloss Low VOC
Enamel, B21WJ Series
1.5
1.6
143
49
Concrete
Masonry
Unit (Pre-
viously
Painted)
Gloss ProMar 200 Zero VOC Latex
Primer, B28W02600 1.5 0 All States except CA:
2 Coats: Pro Mar 200 Interior Latex
Gloss Enamel, B21W200
State of CA:
2 Coats: Solo Gloss Low VOC
Enamel, B21WJ Series
1.5
1.6
143
49
Concrete
Masonry
Unit (New
Construc-
tion)
Egg-
shell
Loxon Concrete and Masonry
Primer, B28W8300 8.0 45 2 Coats: ProMar 200 Zero VOC
Interior Latex Eggshell, B202-
2600 Series
1.5 0
Concrete
Masonry
Unit (Pre-
viously
Painted)
Egg-
shell
ProMar 200 Zero VOC Latex
Primer, B28W02600 1.5 0 2 Coats: ProMar 200 Zero VOC
Interior Latex Eggshell, B202-
2600 Series
1.5 0
Gypsum
Board
Gloss ProMar 200 Zero VOC Latex
Primer, B28W02600 1.5 0 All States except CA:
2 Coats: Pro Mar 200 Interior Latex
Gloss Enamel, B21W200
State of CA:
2 Coats: Solo Gloss Low VOC
Enamel, B21WJ Series
1.5
1.6
143
49
Not For Construction09900-12
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
Surface Sheen 1st Coat DFT
(mils)
VO
C
(g/l)
2nd and 3rd Coats DFT
(mils)
VOC
(g/l)
Gypsum
Board
Semi-
gloss
ProMar 200 Zero VOC Latex
Primer, B28W02600 1.5 0 2 Coats: ProMar 200 Zero VOC
Interior Latex Semi-Gloss Enamel,
B31-2600 Series
1.6 0
Gypsum
Board
Egg-
shell
ProMar 200 Zero VOC Latex
Primer, B28W02600 1.5 0 2 Coats: ProMar 200 Zero VOC
Interior Latex Eggshell Enamel,
B202-2600 Series
1.7 0
Wood Semi-
gloss
ProMar 200 Zero VOC Latex
Primer, B28W02600 1.5 0 2 Coats: ProMar 200 Zero VOC
Interior Latex Semi-Gloss Enamel,
B31-2600 Series
1.6 0
Wood
(Exposed
laminated
wood roof
structure)
Semi-
gloss
PrepRite ProBlock Interi-
or/Exterior Latex Primer Sealer
B51 Series
1.4 97 2 Coats: ProMar 200 Zero VOC
Interior Latex Semi-Gloss Enamel,
B31-2600 Series
1.6 0
Wood
(Transpar-
ent sealer)
Wood Classics Varnish Sanding
Sealer, B26V43 1.2 522
Concrete
Floor Strip-
ing,
Graphics
and Mark-
ings
Semi-
gloss
Macropoxy 646-100, B58W620,
B58V620 5.0-
10.0
<100 Macropoxy 646-100, B58W620,
B58V620 5.0-
10.0
<100
3.12 WAL-MART FURNISHED COATINGS QUANTITY SCHEDULE
A. Elastomeric coating and block filler specified above for indicated “New Construction” shall be furnished by the
General Contractor.
END OF SECTION
Sherwin Williams Coat-
ing Product Number Product Description
Gallons Furnished by
Wal-Mart
EXTERIOR
A6-100 Series A-100 Exterior Latex Finish 0
Sherwin Williams Coat-
ing Product Number Product Description
Gallons Furnished by
WalMart
INTERIOR
B20-2600 ProMar 200 Zero VOC Interior Latex Eggshell Enamel, 15
B31-2600 ProMar 200 Zero VOC Interior Latex Semi-Gloss Enamel 10