07900 - 2901Not For Construction 07900 - 1
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
UniSpec II - Store Planning 032913
SECTION 07900 - JOINT SEALERS
PART 1 - GENERAL
1.1 SUMMARY
A. Section Includes:
1. Joint sealants for interior and exterior joints in vertical surfaces and horizontal nontraffic surfaces, except
as otherwise specified.
2. Joint sealants and fillers in interior concrete floor slab-on-grade joints.
3. Joint sealant and fillers in exterior concrete sidewalks and pavement adjacent to building.
B. Related Sections:
1. Section 01640 - Owner Furnished Products: General procedures related to Owner furnished and installed
products.
2. Division 2: Joint fillers and sealants for joints in sidewalk and pavement not adjacent to building.
3. Section 04200 - Unit Masonry Assemblies: Installation of expansion joint filler (compression seal) and
control joint sealer in masonry walls.
4. Section 07530 - Elastomeric Membrane Roofing: Sealants associated with roofing.
5. Section 07840 - Firestopping: Joint seals around penetrations of fire-rated assemblies.
6. Section 09650 - Resilient Flooring: Joint filler for control/construction joints concealed by floor finish
material.
7. Section 09900 - Paints and Coatings: Protection of wall joints from painting prior to sealing.
A. Work Furnished and Installed by Owner: Sealant specified in this Section for caulking around columns at resilient
flooring will be furnished and installed by the Preferred Flooring Contractor.
1.2 REFERENCES
A. The publications listed below form a part of this specification to the extent referenced. Publications are referenced
within the text by the basic designation only.
B. ASTM International (ASTM):
1. ASTM C920 - Specification for Elastomeric Joint Sealants.
2. ASTM C1330 - Cylindrical Sealant Backing for Use with Cold Liquid Applied Sealants.
3. ASTM D 1056 - Flexible Cellular Materials-Sponge or Expanded Rubber.
4. ASTM E84 - Test Method for Surface Burning Characteristics of Building Materials
1.3 SUBMITTALS
A. Installer Qualification Certification: Provide certification letters for the installers of the following:
1. Polyurea Joint Filler.
B. Letter shall be from the product manufacturer stating that the installer is qualified and certified by the manufactur-
er to install the material to be used, citing the specific project and location.
C. Provide minimum of 15 projects, with locations, performed within the last 3 years, similar in type and size to this
project.
D. Product Data: Brand name, chemical composition, installation directions and certificates of compliance with re-
quired standards for the following products:
1. Elastomeric joint materials (sealant and back-up material).
2. Preformed expansion (isolation) joint filler (PMEJ)
3. Polyurea joint filler.
4. Submit 30 days prior to first concrete placement.
Not For Construction 07900 - 2
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
1.4 QUALITY ASSURANCE
A. Interior sealants in food preparation areas shall meet the compositional requirements for use in USDA regulated
facilities, as required by FDA according to 21 CFR 177.2600, and local authorities having jurisdiction.
1.5 ENVIRONMENTAL REQUIREMENTS
A. Do not install solvent curing sealants in enclosed building spaces.
B. Maintain temperature and humidity recommended by sealant manufacturer during and after installation.
PART 2 - PRODUCTS
2.1 ELASTOMERIC SEALANTS (BUILDING)
A. General: Comply with ASTM C 920 and other requirements indicated for each liquid-applied chemically curing
sealant specified, including those referencing ASTM C 920 classifications for type, grade, class, and uses related
to exposure and joint substrates.
B. Sealants identified as (Non-USDA) shall not be used in food preparation areas.
C. Manufacturers:
1. BASF Building Systems (Formerly Sonneborn Building Products). (952) 496-6000, Craig Agney.
2. Convenience Products, (800) 325-6180.
3. CSS Polymers, Inc. (770) 645-0101.
4. Dow Corning Corporation. www.dowcorning.com
5. Euclid Chemical Co., (877) 438-3826.
6. Franklin International, (800) 877-4583.
7. GE Silicones & GE Sealants and Adhesives (Momentive Performance Materials). (877) 943-7325
www.gesilicones.com
8. Metzger/McGuire, (800) 223-6680.
9. Pecora Corporation. (215) 796-1401, Keith Waters. www.pecora.com
10. Tremco Sealant/Weatherproofing Division. (800) 841-3778. Jack Sykes. www.tremcosealants.com
11. VersaFlex Inc. (913) 321-1416
12. W. R. Meadows, Inc., (847) 214-2100.
D. Polyurethane Sealants (USDA Certified, unless otherwise noted):
1. Polyurethane Sealant #1 (P1): ASTM C920, Type S, Grade NS, Class 25, single component.
a. Vulkem 116, Dymonic, or Dymonic FC by Tremco.
b. Dynatrol I-XL, by Pecora.
c. Sonolastic NP-1, by BASF.
2. Polyurethane Sealant #2 (P2): ASTM C920, Type S, Grade P, Class 25, single component.
a. Vulkem 45 (Non-USDA), by Tremco.
b. Urexpan NR-201, by Pecora.
c. Sonolastic SL-1, by Sonneborn.
3. Polyurethane Sealant #3 (P3): ASTM C920, Type M, Grade NS, Class 50, multi-component.
a. Dymeric 240FC, by Tremco.
b. Sonolastic NP-2 by BASF.
c. Dynatrol II (Non-USDA) by Pecora.
E. Silicone Sealants (USDA Certified, unless otherwise noted):
1. Silicone Sealant #1 (S1): ASTM C920, Type S, Grade NS, Class 25.
a. Spectrem 1, Spectrem 2, or Spectrem 3, by Tremco.
b. 791 Silicone Perimeter Sealant (Non-USDA), by Dow
c. 864 or 890 by Pecora.
d. Sonolastic 150 by BASF.
e. SilPruf (Non-USDA), by GE.
Not For Construction 07900 - 3
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
f. Titebond 100% Silicone Sealant by Franklin International.
2. Silicone Sealant #2 (S2): ASTM C920, Type S, Grade NS, Class 25, mildew resistant.
a. Tremsil 200, by Tremco.
b. 898 by Pecora.
c. 786 Silicone Sealant (Non-USDA), by Dow.
d. Sanitary SCS 1700 (Non-USDA), by GE.
F. Sealant Color:
1. In interior and exterior exposed areas, match color of adjacent paint color finish or other adjacent finish
color.
2. In joints where plumbing fixtures meet adjacent floor and wall finishes, match color of plumbing fixture.
3. Use clear, colorless sealant where applied to stainless steel surfaces.
2.2 EXPANDING FOAM SEALANTS
A. Polyurethane Expanding Foam Sealants:
1. Polyurethane Expanding Foam Sealant #1 (EF1): Closed-cell foam and non-flammable propellant; urea
formaldehyde-free, CFC-free; UL Class 1 Foam with flame spread of 20 and smoke developed of 25 as
tested in accordance with ASTM E84.
a. Touch'n Seal Quick Cure, by Convenience Products.
b. Space Invader by GE Sealants & Adhesives, (877) 943-7325.
2.3 JOINT FILLER (BUILDING)
A. Preformed Control Joint Filler:
1. Regular Joint: 2-5/8 inches by 1-1/2 inches; rubber.
a. RS-STANDARD Control Joint by Hohmann & Barnard, Inc., Hauppauge, NY (800) 645-0616.
b. Masonry Control Joint No. 571 by Greenstreak, St. Louis, MO (800) 325-9504.
2. Tee Joint: 2-5/8 inches by 1 inch; rubber.
a. RS-TEE Control Joint by Hohmann & Barnard.
b. Masonry Control Joint No. 572 by Greenstreak.
B. Expansion Joint Filler (Compression Seal):
1. Backerseal (Grayflex) expanding precompressed foam by Emseal Joint Systems, Ltd., Westborough, MA
(800) 526-8365.
2. Willseal 600 polyurethyene foam joint sealing tape by Willseal USA, Pelham, NH (800) 438-0684.
2.4 JOINT-SEALANT BACKING (BUILDING)
A. Sealant Backing (Backer Rod): Provide sealant backings of material and type that are nonstaining; are compatible
with joint substrates, sealants, primers, and other joint fillers; and are approved for applications indicated by
sealant manufacturer based on field experience and laboratory testing.
1. Cylindrical Sealant Backings: ASTM C 1330, types as approved by joint-sealant manufacturer for joint
application indicated, and of size and density to control sealant depth and otherwise contribute to producing
optimum sealant performance:
a. Backer Rod for Exterior Masonry: Closed cell foam, oversized 50 percent; self-expanding.
2. Elastomeric Tubing Sealant Backings: Neoprene, butyl, EPDM, or silicone tubing complying with
ASTM D 1056,
B. Bond-Breaker Tape: Polyethylene tape or other plastic tape recommended by sealant manufacturer for preventing
sealant from adhering to rigid, inflexible joint-filler materials or joint surfaces at back of joint where such adhesion
would result in sealant failure. Provide self-adhesive tape where applicable.
2.5 INTERIOR SLAB ON GRADE JOINT SEALANT MATERIALS
A. Preformed Expansion (Isolation) Joint Filler (PMEJ) Strips: Flexible closed-cell synthetic foam expansion joint
strips, non-extruding, for full depth of concrete.
Not For Construction 07900 - 4
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
1. Ceramar Flexibe Foam Expansion Joint, by W.R. Meadows.
2. Deck-O-Foam Expansion Joint Filler, by W.R. Meadows
3. Expansion Joint Filler, by BASF Building Systems (Degussa) (Formerly Sonneborn Sonolastic).
B. Elastomeric Joint Materials:
1. Sealant:
a. Polyurethane Sealant: No. 2 (P2) as specified above.
b. Color: Match color of adjacent exposed surface of concrete slab..
c. Sealant shall be compatible with construction material placed against it.
2. Joint Back-Up Material:
a. Polyethylene Foam, 100% closed cell.
b. Material shall be compatible with construction material to be placed against it such as tile adhesive.
C. Polyurea Joint Filler (PY1): Rapid setting, two-component polyurea polymer liquid of 100% solids content, Shore
Hardness 85 to 92, compatible with construction material placed against it. (USDA Certified, unless otherwise
noted.)
1. Spall-Pro RS 88 (Non-USDA), by Metzger/McGuire.
2. Euco Qwik Joint 200 (Non-USDA), by Euclid Chemical.
3. VersaFlex SL/85, by VersaFlex.
4. Quick Joint 85, by CSS Polymers.
5. Match color of adjacent exposed surface of concrete.
2.6 EXTERIOR PAVEMENT JOINT MATERIALS
A. Joint Back-up Material: Polyethylene foam, 100% closed cell
B. Sealant:
1. Dow 888, by Dow Corning.
2. 301 NS by Pecora.
3. Spectrum 800 or 900 by Tremco.
C. Soft Preformed Joint Filler: Flexible closed-cell non-extruding synthetic foam expansion joint strips.
1. Ceramar Flexibe Foam Expansion Joint, by W.R. Meadows.
2. Deck-O-Foam Expansion Joint Filler, by W.R. Meadows
3. Expansion Joint Filler, by BASF Building Systems (Degussa) (Formerly Sonneborn Sonolastic).
2.7 ACCESSORIES
A. Primer: Non-staining type, recommended by sealant manufacturer to suit application.
B. Joint Cleaner: Non-corrosive and non-staining type, recommended by sealant manufacturer; compatible with joint
forming materials.
PART 3 - EXECUTION
3.1 EXAMINATION
A. Verify that surfaces and joint openings are ready to receive work and field measurements are as indicated on
Drawings.
B. Beginning of installation means installer accepts existing substrates.
3.2 PREPARATION
A. Clean and prime joints in accordance with manufacturer's instructions.
B. Remove loose materials and foreign matter which might impair adhesion of sealant.
Not For Construction 07900 - 5
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
C. Verify that joint backing and release tapes are compatible with sealant.
D. Protect elements surrounding work of this Section from damage or disfiguration.
3.3 INSTALLATION
A. Install sealant in accordance with manufacturer's instructions.
B. Measure joint dimensions and size materials to achieve required width/depth ratios.
C. Install sealant backings of kind indicated to support sealants during application and at position required to produce
cross-sectional shapes and depths of installed sealants relative to joint widths that allow optimum sealant move-
ment capability.
1. Do not leave gaps between ends of sealant backings.
2. Do not stretch, twist, puncture, or tear sealant backings.
3. Remove absorbent sealant backings that have become wet before sealant application and replace them with
dry materials.
D. Install bond breaker where joint backing is not used.
E. Apply sealant within recommended temperature ranges. Consult manufacturer when sealant cannot be applied
within recommended temperature ranges.
F. Install sealant free of air pockets, foreign embedded matter, ridges, and sags.
G. Tool joints concave.
3.4 INTERIOR SLAB ON GRADE JOINT SEALING AND FILLING
A. General:
1. Seal/fill contraction, isolation and construction joints in floor slabs and pavements, unless otherwise
indicated on Drawings or specified herein.
2. Unless noted otherwise, use polyurea joint filler in floor slab contraction and construction joints and use
elastomeric joint sealant in isolation joints.
3. Use pavement sealant in pavement’s contraction, construction, and isolation joints.
4. Do not seal joints with materials specified herein when below relatively impervious floor finish material,
such as PVC flooring, sheet rubber, wood, epoxy topping; refer to floor finish specification for joint sealing
requirements.
5. Do not place polyurea joint filler under resilient flooring. Coordinate placement of polyurea joint filler with
joint filler placement specified under resilient flooring as specified in Section 09650.
B. Cleaning:
1. Immediately prior to sealing/filling, clean joints to full depth of sealant/filler in accordance with
manufacturer’s recommendation.
2. Remove dirt, debris, saw laitance, and other foreign material from joint. Clean inner joint walls
mechanically using dustless dry-cut saw, or similar tool, to the full depth of saw cuts and 2 inch minimum
depth in construction joints.
3. Remove form release agent, curing compound, or other components.
C. General Installation:
1. Commence placing floor joint sealant / filler no sooner than 30 days after first placement of concrete.
2. If joint is wet or damp, allow joint to dry for 72 hours prior to filling.
3. Delay floor joint sealing / filling operations until facility’s environmental systems have been placed in
operation for 14 days.
4. Mix and install sealant and filler in accordance with manufacturer’s recommendations. Use primer if
recommended for specific application.
Not For Construction 07900 - 6
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
5. Choke off shrinkage crack if necessary at bottom of contraction joint or void below construction joints by
the following methods.
a. Saw Cut Contraction Joints:
1) Place 1/8 inch to 1/4 inch (maximum) layer of dry-bagged silica sand. Do not use compressi-
ble backer rod.
b. Construction Joints Through Slab: Fill by one of the following methods:
1) Fill joint with dry-bagged silica sand to within 2 inches of slab surface.
2) Insert compressible backer rod to a minimum depth of 2 inches below slab surface.
6. Do not allow sealant / filler to extend over joint edges in finished condition.
D. Elastomeric Joint Sealant Installation:
1. Use joint back-up material.
2. Tool surface to provide smooth, attractive appearance and geometry recommended by sealant
manufacturer.
E. Joint Filler Installation
1. Installation shall be by installer who is approved in writing by the manufacturer’s corporate office for this
project.
2. Do not use joint back-up material (i.e. backer rod, sand, etc.) except below bottom of saw cut in
construction joints. Provide a minimum joint filler depth of 2 inches.
3. Install test sample of the polyurea joint filler to determine if filler will leave a stain, shadow, or film on slab
surface.
4. If test sample reveals stain, shadow, or film, use joint filler stain preventing film at joints to receive
polyurea joint filler.
5. Fill joint using single pass method. Fill joint full depth from bottom to top, leave slight crown at slab
surface.
6. Add extra filler prior to filler set if needed to prevent depressed areas. If concave filler is already set,
abrade with wire wheel or similar tool to minimum depth of 1/4” below surface prior to refilling.
7. Razor off crowned filler flush with floor surface after filler has sufficiently set.
8. Remove stain preventing film (if used). Film shall be removed by joint filler installer immediately after
shaving joint filler.
9. One week prior to Grand Opening, refill joints if:
a. Joint filler sidewall separation or splitting exceeds 1/32 in.
b. Joint filler surface profile is concave, crowned, or chattered or if voids occur.
10. Follow manufacturer’s requirements for joint preparation for proper adhesion.
F. Isolation Joints: Form isolation joints of preformed joint-filler strips (PMEJ) where indicated.
1. Extend joint fillers full width and depth of joint.
2. Terminate joint filler or otherwise provide joint sealant cavity of not less than 1/2 inch or more than 1 inch
below finished surface if joint sealant is indicated.
3. Place top of joint filler flush with finished concrete surface if joint sealant is not indicated.
4. Furnish joint fillers in one-piece lengths. Where more than one length is required, lace or clip joint-filler
sections together.
5. Protect top edge of joint filler during concrete placement with metal, plastic, or other temporary preformed
cap. Remove protective cap after concrete has been placed on both sides of joint.
3.5 EXTERIOR SIDEWALK AND PAVEMENT JOINT SEALING AND FILLING
A. Fill and seal sidewalk and pavement joints in areas of pavement adjacent to the building. Joint filling and sealing
of sidewalks and pavement not adjacent to building is specified in Division 2.
B. Joint Fillers: Extend joint fillers full-width and depth of joint, and not less than 1/2-inch or more than 1-inch be-
low finished surface where joint sealer is indicated. Furnish joint fillers in 1-piece lengths for full width being
placed, wherever possible. Where more than 1 length is required, lace or clip joint filler sections together.
C. Joint Sealants: Joints shall be sealed as shown and scheduled and shall be installed in accordance with manufac-
turer's recommendations.
Not For Construction 07900 - 7
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
3.6 SCHEDULE
A. Provide sealants in accordance with the following schedule. Joint sealing required by the drawings or required for
a complete and proper installation but not listed in the following schedule shall be sealed as necessary regardless
of whether shown or scheduled. Such joints not shown or scheduled shall be sealed with sealants consistent with
specified materials or as recommended by the manufacturer for the specific application.
Not For Construction 07900 - 8
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
EXTERIOR JOINTS
MATERIAL TO MATERIAL JOINT
WIDTH
SEALANT TYPE
SITE Concrete Sidewalk Control Joint Concrete Sidewalk 1/4" Sidewalks adjacent to
building: See Materi-
als Par. Otherwise:
See Division 2.
Concrete Sidewalk Expansion Joint Concrete or CMU 1/2" See above
Concrete Paving Control Joint Concrete Paving 1/4" Pavement adjacent to
building: See Materi-
als Par. Otherwise:
See Division 2.
Concrete Paving Expansion Joint Concrete 1/2" See above
Concrete Stair Expansion Joint Concrete or CMU 1/2" P1 or P3
Concrete Curb Expansion Joint Concrete or CMU 1/2" See Division 2
BUILDING
WALL
CMU Wall Control Joint, 3/8" CMU Wall 3/8" P1 or P3
CMU Wall Expansion Joint, 1" CMU Wall 1" P1 or P3
EIFS Wall CMU or Cast Concrete
shapes
1/2" P1 or P3
EIFS Cornice/Trim CMU or EIFS 1/2" P1 or P3
WALL
FLASHING
Metal Flashing Metal Flashing S1
Metal Flashing CMU, EIFS, Aluminum
Storefront Frame
1/4" P1 or P3
SOFFITS Gypsum Soffit Control Joint Gypsum Soffit 3/8" P1 or P3
Gypsum Soffit Perimeter Expansion
Joint
EIFS or CMU 3/8" P1 or P3
Metal Soffit Panel Trim EIFS or CMU P1 or P3
WALL PENE-
TRATIONS
Aluminum Storefront Frame CMU, EIFS, Aluminum
Storefront Frame
1/4" P1 or P3
Aluminum Storefont Sill Cast Concrete Shapes or
Concrete Slab
1/4" P1 or P3
Aluminum Storefront Door Threshold Concrete Slab P1 or P3
Translucent Insulated Panels Translucent Insulated
Panels, EIFS, Metal Flash-
ing
1/4" S1
Hollow Metal Door Frame CMU Wall, Tube Steel
Frame
1/4" P1 or P3
Hollow Metal Door Threshold Concrete Slab P1 or P3
Steel Corner Angle Frame CMU Wall 1/4" P1 or P3
Steel Pipe and/or Conduit Through CMU, EIFS, Concrete 1/2" P1 or P3
Ganged Steel Conduit Through CMU, EIFS, Concrete 1/2" P3
PVC and/or Copper Pipe Through CMU, EIFS, Concrete 1/2" P1 or P3
ROOF
MEMBRANE
Roofing Membrane Roofing Membrane See Roofing Section
Roofing Membrane Waterproof Wall Membrane See Roofing Section
Not For Construction 07900 - 9
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
EXTERIOR JOINTS
MATERIAL TO MATERIAL JOINT
WIDTH
SEALANT TYPE
AREA Roofing Membrane Metal Facia See Roofing Section
Roofing Membrane Molded Pipe Flashing See Roofing Section
Waterproof Membrane Metal Facia, Plates, Bolts P1 or P3
Waterproof Membrane Steel Conduit 1/2" P1 or P3
Metal Cap Flashing Joint Metal Cap Flashing 1/8" S1
Metal Cap Flashing Expansion Joint Metal Cap Flashing 1" S1
Metal Cap Flashing Gasketed Fasteners S1
Skylight Flashing Joints Skylight Flashing S1
Vent Flashing Joints Vent Flashing S1
Smoke Vent Flashing Joints Smoke Vent Flashing S1
RTU Flashing Joints RTU Flashing S1
Waterproof Membrane Termination
Bar
CMU Wall 1/4" S1
Steel Gutter Steel Gutter or Downspout S1
Steel Downspout Steel Downspout S1
Urethane Rubber Seal System Steel Pipe/ Flue Varies See Section 07530
ROOF
METAL/
FIBERGLASS
PANELS
Roof Panel Flue Penetration Flashing P1 or P3
Roof Panel Gutter P1 or P3
Roof Panel End Closure P1 or P3
INTERIOR JOINTS
MATERIAL TO MATERIAL JOINT
WIDTH
SEALANT TYPE
FLOOR Concrete Floor Concrete Floor
Contraction and Construction Joint 1/4" See Materials Par.
Expansion Joint 3/4" Same
Isolation Joint See
Dwgs
Same
Concrete Curb In Grocery Concrete Floor Same
Ceramic Tile Expansion Joints Ceramic Tile Ref Mfr. P1 or P3
Quarry Tile Expansion Joints Quarry Tile Ref Mfr. P1 or P3
Floor Joints Beneath Floor Finish
Materials (VCT or PVC Flooring)
See Section 09650
Transition Strip (Korlyte) Concrete Slab PY1
Mop Sink Floor P1 or P3
Sanitary Cove Base (SCB) Floor See Section 09655
Wood Base Concrete Floor P1 or P3
Structural Steel Column VCT/PVC P1
WALLS CMU Wall Control Joint, 3/8" CMU Wall 3/8" P1
CMU Wall Expansion Joint, 1" CMU Wall 1" P1
Not For Construction 07900 - 10
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
INTERIOR JOINTS
MATERIAL TO MATERIAL JOINT
WIDTH
SEALANT TYPE
Rated Gypsum Board Wall Control
Joint
Rated Gypsum Board Wall
Rated Gypsum Board Wall Metal Roof Deck or Rated
CMU Wall
See Section 07840 -
Firestopping
Gypsum Board CMU Walls 3/8" P1 (Use edge trim,
ref. Section 09250)
Ceramic Tile Wood or Galvanized Steel
Base Trim
P1 or P3
Ceramic Tile Stainless Steel S1 or S2
Ceramic Tile Ceramic Tile P1 or P3
Fiber Reinforced Wall Panel (FRP) Galvanized Steel Base Trim See Section 06610
Fiber Reinforced Wall Panel (FRP) Ceramic Tile See Section 06610
Stainless Steel Corner Guards Ceramic Tile S1 or S2
Stainless Steel Corner Guards Wall S1 or S2
Plastic Base Grocery Equipment Wall P1 or P3
Plastic Base Ceramic Tile or Gypsum
Board Wall
P1 or P3
Plastic Base Concrete or Quarry Tile
Floor
P1 or P3
Sanitary Cove Base (SCB) Wall See Section 09655
Wood Base Plywood Wainscot P1
Joints shown on the drawings to be
sealed with Expanding Foam Sealant
EF1
WALL
PENETRA-
TIONS
Aluminum Storefront Frame Alum Storefront Frame,
CMU, or Gypsum Board
1/4" P1
Aluminum Storefront Sill Gypsum Board Wall or Cast
Concrete Shapes
1/4" P1
Hollow Metal Door Frame CMU or Gypsum Board 1/4" P1
Steel Corner Angle Frame CMU Wall 1/4" P1
Steel Pipe or Conduit Through CMU Wall 1/2" P1
Steel Pipe or Conduit Through Gypsum Board 1/4" P1
PVC or Copper Pipe Through CMU or Gypsum Board 1/2" P1
Steel, PVC, or Copper Pipe Through Rated CMU or Gypsum
Board Wall
See Section 07840
Steel Conduit Through Rated CMU or Gypsum
Board Wall
See Section 07840
TOILET Sink Ceramic Tile Wall S2
FIXTURES Floor Mount Toilet Ceramic Tile Floor S2
Wall Mount Toilet or Urinal Ceramic Tile Wall S2
GROCERY
EQUIP
Pre-manufactured Freezer Concrete Curb P1 or P3
Pre-manufactured Freezer Plastic Transition Strip P1 or P3
Not For Construction 07900 - 11
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
INTERIOR JOINTS
MATERIAL TO MATERIAL JOINT
WIDTH
SEALANT TYPE
Pre-manufactured Freezer Concrete Floor P1 or P3
Refrigerated Case Trim Refrigerated Case S1 or S2
Refrigerated Case Trim Concrete Floor S1 or S2
Stainless Steel Equipment Fiberglass Reinforced Plas-
tic (FRP) Wall Panels
S1 or S2
Stainless Steel Equipment Ceramic Tile S1 or S2
EWC Electric Water Coolers Ceramic Tile P1 or P3
COUNTER Plastic Laminate Counter Tops Gypsum Board or Plastic
Laminate Walls
S2
END OF SECTION
Not For Construction 07900 - 12
2901 - Northampton, Massachusetts - 1452013 April 21, 2015