06400 - 2901Not For Construction 06400 - 1
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
UniSpec II- Store Planning 082914
SECTION 06400 - ARCHITECTURAL WOODWORK
PART 1 - GENERAL
1.1 SUMMARY
A. Section Includes:
1. Plastic Laminate Casework.
2. High Pressure Laminate (HPL) Wainscoting.
3. Metal Edge Trim.
B. Related Sections:
1. Section 06100 - Rough Carpentry: Lumber and panel products used for wood and wire mesh doors.
2. Section 06424 – Protective Surfacing: Polyester blend compound, high impact, rigid sheet wall covering.
3. Section 07240/07243 - Exterior Insulation and Finish System: EIFS Cornice Trim
1.2 REFERENCES
A. The publications listed below form a part of this specification to the extent referenced. Publications are referenced
within the text by the basic designation only.
B. American National Standards (ANSI):
1. ANSI A208.1 - Particleboard
2. ANSI A208.2 - Medium Density Fiberboard For Interior Use
C. Architectural Woodworking Institute (AWI)
1. AWI – Architectural Woodwork Quality Standards Illustrated.
2. AWI Architectural Woodwork Standards replaces the AWI Architectural Woodwork Quality Standards Il-
lustrated and the Woodwork Institute’s (WI) Manual of Millwork upon availability first quarter of 2009.
D. Engineered Wood Association (APA): APA - Grades & Specifications.
E. National Electrical Manufacturer's Association (NEMA)
1. NEMA LD3 - High-Pressure Decorative Laminates
1.3 DELIVERY, STORAGE AND HANDLING
A. Transport, handle, store, and protect products in compliance with the requirements of Section 01600.
B. Inspect materials delivered and reject those not qualifying with requirements, those damaged in transit, or those
that appear otherwise unsatisfactory.
C. Schedule delivery of items to installation areas that are in proper condition to receive them. Place items neatly and
systematically to avoid damage, store in clean, dry, enclosed, and secure storage area.
PART 2 - PRODUCTS
2.1 LAMINATE MATERIALS
A. Manufacturers: Provide products as manufactured by the following as specified in the Color/Pattern Schedule be-
low:
1. Formica Corporation; Indianapolis, IN; Contact: Megan Shaughnessy; (513) 786-3039.
2. Nevamar Decorative Surfaces; Hampton, SC (800) 638-4380.
3. Pionite Decorative Surfaces; Auburn, ME; (800) 746-6483.
4. Wilsonart; Temple, TX; Contact:Mark Kieckhafer, (254) 207-2381.
Not For Construction 06400 - 2
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
B. High pressure laminate (HPL); NEMA LD3; color, pattern, and finish as indicated in this Section.
1. Exposed Horizontal Surfaces: GP-50.
2. Exposed Vertical Surfaces: GP-50.
3. Postformed Surfaces: PF-42.
4. Thickness: Nominal 0.050 inch thick.
2.2 ACCESSORIES
A. Adhesives: Low VOC adhesive, as recommended by laminate manufacturer and suitable for shop or field applica-
tion.
1. Toxicity / IEQ:
a. Comply with applicable regulations regarding toxic and hazardous materials.
b. Comply with Green Seal Standard GS-36 for commercial aerosol adhesives.
c. Comply with California’s South Coast Air Quality Management District (SCAQMD) Rule No. 1168
in areas where exposure to freeze/thaw conditions and direct exposure to moisture will not occur. In
areas where freeze/thaw conditions exist or direct exposure to moisture can occur, then comply with
California’s Bay Area AQMD Regulation 8, Rule 51 for containers larger than 16 oz. and with Cali-
fornia Air Resource Board (CARB) for containers 16 oz or less.
2. Acceptable Products: Provide the following or equivalent as recommended by laminate manufacturer.
a. Wilsonart 3000 Adhesive Series.
b. Sta’-Put SP80.
c. Titebond
B. Fasteners: Unless otherwise recommended by the manufacturer, use size and type to suit application; galvanized or
stainless for exterior and high humidity locations; plain finish at other locations.
C. Metal Edge Trim: Extruded aluminum shapes, smooth surface, anodized finish. Size and type to suit application:
1. Manufacturers: Provide metal edge trim manufactured by one of the following, unless otherwise specified.
a. Macklanburg-Duncan, Oklahoma City, OK (800) 654-0007.
b. Outwater Plastics Industries, Inc.
1) East Coast: Bogota, NJ (800) 631-8375.
2) West Coast: Phoenix, AZ (800) 248-2067.
c. Loxcreen, West Columbia, SC (817) 640-4456.
d. Stylmark, Minneapolis, MN (800) 328-2495.
e. Alternate Manufacturers: As approved by the Wal-Mart Construction Manager.
2.3 COLOR/PATTERN SCHEDULE
A. Provide one color where two or more are specified. Provide laminate specified below as applicable and as
shown/scheduled on the Drawings. All PL designations are for HPL unless otherwise indicated. Colors shown in
parentheses are generic color names.
1. PL-1 (Light Gray):
a. No. 692 Folkstone Celesta, by Formica.
b. No. 4142-60 Grey Glace, by Wilsonart.
2. PL-2 (White): No. D354-60 Designer White, matte finish, by Wilsonart.
3. PL-3: Not Used.
4. PL-4 (Maple):
a. No. WM791 Hardrock Maple, by Pionite.
b. No. 10776HW-60 Kensington Maple, by Wilsonart
5. PL-5 (Gray):
a. No. D92-60 Dove Grey, by Wilsonart.
6. PL-6 (Light Tan): No. 4143-60 Neutral Glace, by Wilsonart.
7. PL-7 (Medium Brown): No. 96-60 Shadow, by Wilsonart.
8. PL-8 (Sand):
a. No. AG381 Mineral Talc, by Pionite.
b. No. 1763-60 Brune Slate, by Wilsonart.
9. PL-9 (Dark Gray):
Not For Construction 06400 - 3
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
a. No. SG228 Slate, by Pionite.
b. No. D91-60 Slate Grey, by Wilsonart.
10. PL-10: No. D436-60 Fleece, by Wilsonart.
11. PL-11 (Dark Gray): No. 4623-60 Graphite Nebula, by Wilsonart.
12. PL-12 (Black): No. 1595-60 Black by Wilsonart.
13. PL-13: No. ST622-S Caramel, by Pionite.
14. PL-14: No. 4680 Lodestone, by Wilsonart.
15. PL-15: (Brown): No. MKT-001T Golden Iron Moonrock, by Nevamar.
16. PL-16: No. 4745HW-60 Maroochy Brush, by Wilsonart
17. PL-18: (Medium Tan): No. PON-003T Painted Desert, by Nevamar.
18. PL-19: No. ARP S2003 Champagne, by Nevamar.
19. PL-20 (Tan): No. 4762HW-60 Mystique Dawn, by Wilsonart.
20. PL-21 (Fonthill Pear): No. 10745-60 Fonthill Pear, by Wilsonart.
21. PL-22: No. 1815-35 Deepstar Agate, by Wilsonart.
22. PL-23 (Dark Gray):
a. No. 928-58 Mouse (matte finish), by Formica.
b. No. D90-60 North Sea, by Wilsonart.
23. PL-24 (Blue): No. D321-60 Brittany Blue, by Wilsonart.
24. PL-26 (Sol): No 3209-58 “Sol”, by Formica.
25. PL-28 (Aloe): No. 7962K-18 Aloe, by Wilsonart.
B. Substitutions: Not permitted.
2.4 PLASTIC LAMINATE CASEWORK
A. Fabricate to AWI Standards.
1. Plastic Laminate Casework: Custom Grade, reveal overlay construction.
a. Exposed Surfaces: High pressure laminate, nominal 0.050 inch thick.
b. Semi-Exposed Surfaces: High pressure laminate, nominal 0.028 inch thick.
c. Concealed Surfaces: Mill option.
B. Panel Product Substrate for Laminate Clad Casework: Medium Density Fiberboard (MDF), ANSI A208.2, Grade
MD or 45 lb density particleboard ANSI A208.1, Grade M-2.
C. Cabinet Hardware:
1. Base Cabinets:
a. Drawer Slides Knape & Vogt (KV) 1300
b. Drawer Lock KV 986 NP
c. Shelf Standards KV 255ZC
d. Shelf Supports KV 239
2. Doors:
a. Wire Pull Ives 36 B26D
b. Door Lock KV 986 NP
c. Hinges Rockford Process IH 860
d. Magnetic Catches Ives 325 (A 92)
D. Fasteners: Unless otherwise recommended by the manufacturer, use size and type to suit application; galvanized or
stainless for exterior and high humidity locations; plain finish at other locations.
2.5 MOLDED LAMINATE COUNTERTOP
A. Postformed plastic laminate on 3/4” particle core with waterfall edge trim and integral backsplash, all one-piece
design, length and width as shown.
B. Manufacturer: Belanger Laminates VT Inc. (800) 264-3440, similar to Belanger style 1000, 1100, or 2100. As
distributed by Lowes (Model # 3526118) or Home Depot or equivalent by other manufacturers.
Not For Construction 06400 - 4
2901 - Northampton, Massachusetts - 1452013 April 21, 2015
C. Color: Travertine or Sandstone.
2.6 LAMINATE WAINSCOT PANELS
A. Provide wainscot from high pressure laminate (HPL) materials specified above as shown on the Drawings.
2.7 CORNER GUARDS
A. Corner Guards: Aluminum corner guards specified in Section 10260.
PART 3 - EXECUTION
3.1 GENERAL
A. Install items specified herein where and as shown on the Drawings.
3.2 PLASTIC LAMINATE CASEWORK
A. Where new plastic laminate is indicated for existing caswork, remove existing laminate and/or finishes to base
substrate prior to installation of new. Installation of new laminate over existing is not acceptable, no exceptions.
B. Install woodwork plumb, level, and straight without distortion; use concealed shims. Scribe and cut woodwork to
fit adjoining work. Anchor woodwork items to nailers or blocking or directly to substrate using concealed fasten-
ers.
C. Casework: Provide well fitting and smooth operating doors and drawers.
D. Countertops: Anchor plastic laminate countertops securely to base units.
E. Install laminate with directional pattern or grain oriented vertically.
3.3 LAMINATE WAINSCOT
A. Examine surfaces and adjacent areas where wainscot will be installed and verify that substrates are flat, clean, dry,
solid, and free from coatings and defects detrimental to installation. Verify that surfaces conform to product man-
ufacturer's requirements for substrate conditions unless otherwise shown or specified.
B. Where new plastic laminate wainscot is to be installed, remove existing laminate and/or finishes to base substrate
prior to installation of new. Installation of new laminate over existing is not acceptable, no exceptions.
C. Prepare substrate for laminate wainscot installation in accordance with manufacturer's published instructions and
recommendations unless otherwise shown or specified.
D. Lay out laminate wainscot before installing.
E. Securely attach wainscot panels to substrate at locations shown on the Drawings with adhesive specified in this
Section.
F. Provide extruded aluminum trim at joints between laminate panels and at exposed vertical and horizontal edges of
laminate.
G. Install woodgrain laminate with grain oriented vertically.
END OF SECTION