24B-066 (29) 243 KING ST - SUITE 112 SM-2019-0019
COMMONWEALTH OF MASSACHUSETTS
CITY OF NORTHAMPTON
GIS 9167
Map: 24B
'810-1 066 SHEETMETAL PERMIT
Lat: QO1
Permit: SHEETMETAL,
Category: ISHEETMETAL l
Permit# SM2019-0019 PERMISSION IS HEREBY GRANTED TO.
Project# JS-2019-000700
st Cost:
$8,500.00 Contractor: License: Expires:
!Fee Charged:$100.00AARON MORIN Sheetmetal-533 10/28/2019
Balance Due:$.00 Owner. COOLIDGE NORTHAMPTON LLC C/O HOULIHAN-PARNES/ICRP REA
#of Fixtures: Applicant: AARON MORIN
DigSafe# AT. 243 KING ST-SUITE 112
userxroup
ConstClass
ISSUED ON: 12-Oct-2018 AMENDED ON. EXPIRES ON.
TO PERFORM THE FOLLOWING WORK.•
UPGRADING NEW HVAC SYSTEM
THIS PERMIT MAY BE REVOKED BY THE CITY OF NORTHAMPTON UPON VIOLATION OF
ANY OF ITS RULES AND REGULATIONS.
Signature:
Fee Type: Receipt No: Date Paid: Check No: Amount:
Sheetmetal REC-2019-001242 09-Oct-18 3579 $100.00
212 Main Street,Phone:(413)587-1240,Fax:(413)587-1272,Email:Ihasbrouck@northamptonma.gov
GeoTMS®2018 Des Lauriers Municipal Solutions,Inc.
File#SM-2019-0019
APPLICANT/CONTACT PERSON AARO'` MORIN
ADDRESS/PHONE 140 WEST ST (413),247-0550 Q
PROPERTY LOCATION 243 KING ST-'SU'TE 112
MAP 24B PARCEL 066 001 ZONE HB(98)/GI(2)/
THIS SECTION FOR OFFICIAL USE ONLY:
PERMIT APPLICATION CHECKLIST
NCLOSED REQUIRED DATE
ZONINGFORM FILLED OUT _
Fee Paid
Building Permit Filled out
Fee Paid
Typeof Construction: UPGRADING NEW RVAC§YSTEM
New Construction _
Non Structural interior renovations
Addition to Existing
Accessory Structure
BuildingPlans Included:
Owner/Statement or License 533
3 sets of Plans/Plot Plan
THE FOLLOWING ACTION HAS BEEN TAKEN ON THIS APPLICATION BASED ON
INFORMATION PRESENTED:
t Approved Additional permits required(see below)
I
PLANNING BOARD PERMIT REQUIRED UNDER: §
Intermediate Project: Site Plan AND/OR Special Permit with Site Plan
Major Project: Site Plan'AND/OR Special Permit with Site Plan
ZONING BOARD PERMIT REQUIRED UNDER: §
Finding Special Permit _ Variance*
Received&Recorded at Registry of Deeds Proof Enclosed
Other Permits Required:
Curb Cut from DPW Water Availability Sewer Availability
Septic Approval Board of Health Well Water Potability Board of Health
Permit from Conservation Commission Permit from CB Architecture Committee
Permit from Elm Street Commission Permit DPW Storm Water Management
/ to
Signature of Building Official Date
Note: Issuance of a Zoning permit does not relieve a applicant's burden to comply with all zoning
requirements and obtain all required permits from Board of Health,Conservation Commission,Department
of public works and other applicable permit granting authorities.
*Variances are granted only to those applicants who meet the strict standards of MGL 40A. Contact the Office of
Planning&Development for more information.
Commonwealth of Massachusetts
Sheet Metal Permit
m
Z� —1 Permit#
0 0 mate:
n ()
D G —4
o ,Estim Job Cost: $ 9,S2V,00 Permit Fee: $
z co
q rB ans itted: YES G"NO Plans Reviewed: YES NO
M Go
Busin cense# S�3 Applicant License#
w
Business I f ation: Property Owner/Job
/jLocation Information:
Name: Name:�6o� e /lsil'T Z-/.C
Street: /PSt �7�l�Pi� Street:
City/Town: 1-4?-Sr/7�k �° ��%" City/Town: r�Q �—
Telephone:_ Telephone:
Photo I.D. required/Conv of Photo I.D. attached: YESL NO
Staff Initial
J-1 - -unrestricted license
J-2/M-2-restricted to dwellings 3-stories or less and commercial up to 10,000 sq. ft. /2-stories or less
Residential: 1-2 family Multi-family Condo /Townhouses Other
Commercial: Office Retail Industrial Educational
InstitutionalOther
Square Footage: under 10,000 sq. ft. over 10,000 sq. ft. Number of Stories:
Sheet metal work to completed: New Work: Renovation:
HVAC Metal Watershed Roofing Kitchen Exhaust System
Metal Chimney/Vents Air Balancing
Provide detailed description of work to be done:
l
�eo yr-( �'` r ( C',�;�, ---
INSURANCE COVERAGE:
I have a current liability insurance policy or its equivalent which meets the requirements of M.G.L.Ch. 112 Yes No❑
If you have checked Yes, indicate the t of coverage by checking the appropriate box below:
A liability insurance policy Other type of indemnity ❑ Bond ❑
,
OWNER'S INSURANCE WAIVER: I am aware that the licensee does not have the insurance coverage required by Chapter 112,of the
Massachusetts General Laws, and that my signature on this permit application waives this requirement.
Check One Only
Owner ❑ Agent ❑`.,
Signature of Owner or Owner's Agent
By checking this boxE]I hereby certify that all of the details and information I have submitted(or entered)regarding this application are true and
accurate to the best of my knowledge and that all sheet metal work and installations performed under the permit issued for this application will be
in compliance with all pertinent provision of the Massachusetts Building Code and Chapter 112 of the General Laws.
Duct inspection required prior to insulation installation: YES NO
Progress Inspections
Date Comments
Final Inspection
Date Comments
By ;of se:
aster
Title F-1 M aster-Restricted
City/Town
❑Journeyperson Signature of Licensee
Permit#
❑Journeyperson-Restricted License Number:
Fee$
❑ Check at www.mass.aov/dol
Inspector Signature of Permit Approval
The Commonwealth of Massachusetts
Department of Industrial Accidents
I Congress Street,Suite 100
Boston,MA 02114-2017
U4 www.massgov/dia
Workers'Compensation Insurance Affidavit:Builders/Contractors/Electricians/Plumbers.
TO BE FILED WITH THE PERMITI NG AUTHORITY.
Avolicant Information Please Print Le ibl
Name(Business/Organization/Individual): `_ _ -�--ar• r�
Address: ��Yo
City/State/Zip:V. -1A,Y-P`e oo Phone#: 97 3 ya 7 —/t?"I 6
Are you an ployer?Check the approprlate box:
Type of project(required):
1. am a employer with _employees(full and/or part-time).* 7. ❑New construction
2.❑I am a sole proprietor or partnership and have no employees working for me in 8. ❑Remodeling
any capacity.[No workers'comp.insurance required.]
9. El Demolition
3.❑I am a homeowner doing all work myself.[No workers'comp.insurance required.]t
4.❑1 am a homeowner and will be hiring contractors to conduct all work on my property. I will 10❑Building addition
ensure that all contractors either have workers'compensation insurance or are sole 11.❑Electrical repairs or additions
proprietors with no employees. 12.❑Plumbing repairs or additions
5.❑I am a general contractor and I have hired the sub-contractors listed on the attached sheet. 13.E]Roof repairs
These sub-contractors have employees and have workers'comp.insurance?
6.❑We are a corporation and its officer:have exercised their right of exemption per MGL c. 14 ther �--
152,§1(4),and we have no employees.[No workers'comp.insurance required.]
*Any applicant that checks box#1 must also fill out the section below showing their workers'compensation policy information.
I Homeowner:who submit this affidavit indicating they are doing all work and then hire outside contractors must submit a new affidavit indicating such.
tContractors that check this box must attached an additional sheet showing the name of the sub-contractors and state whether or not those entities have
employees. If the sub-contractors have employees,they must provide their workers'comp.policy number.
I am an employer that is providing workers'compensation insurance for my employees. Below is the policy and job site
information. A0,
Insurance Company Name:
Policy#or Self-ins.Lic.#: / /0 ! I Expiration Date: — 7 — O I
Job Site Address: y'7 K.h�I �T- �Lt.` #�/ City/State/Zip:
Attach a copy of the workers'compensation policy declaration page(showing the policy number and expiration date).
Failure to secure coverage as required under MGL c. 152,§25A is a criminal violation punishable by a fine up to$1,500.00
and/or one-year imprisonment,as well as civil penalties in the form of a STOP WORK ORDER and a fine of up to$250.00 a
day against the violator.A copy of this statement may be forwarded to the Office of Investigations of the DIA for insurance
coverage verification.
Ido hereby cerdit u er thepains and penalties ofperjury that the information provided above is true and correct
Signature: Date:
Phone M -3 1'Y1 6
Official use only. Do not write in this area,to be completed by city or town official
City or Town: PermittUcense#
Issuing Authority(circle one):
1.Board of Health 2.Building Department 3.City/Town Clerk 4.Electrical Inspector 5.Plumbing Inspector
6.Other
Contact Person: Phone M
Information and Instructions
Massachusetts General Laws chapter 152 requires all employers to provide workers'compensation for their employees.
Pursuant to this statute,an employee is defined as"...every person in the service of another under any contract of hire,
express or implied,oral or written."
An employer is defined as"an individual,partnership,association,corporation or other legal entity,or any two or more
of the foregoing engaged in a joint enterprise,and including the legal representatives of a deceased employer,or the
receiver or trustee of an individual,partnership,association or other legal entity,employing employees. However the
owner of a dwelling house having not more than three apartments and who resides therein,or the occupant of the
dwelling house of another who employs persons to do maintenance,construction or repair work on such dwelling house
or on the grounds or building appurtenant thereto shall not because of such employment be deemed to be an employer."
MGL chapter 152,§25C(6)also states that"every state or local licensing agency shall withhold the issuance or
renewal of a license or permit to operate a business or to construct buildings in the commonwealth for any
applicant who has not produced acceptable evidence of compliance with the insurance coverage required."
Additionally,MGL chapter 152,§25C(7)states"Neither the commonwealth nor any of its political subdivisions shall
enter into any contract for the performance of public work until acceptable evidence of compliance with the insurance
requirements of this chapter have been presented to the contracting authority."
Applicants
Please fill out the workers'compensation affidavit completely,by checking the boxes that apply to your situation and,if
necessary,supply sub-contractor(s)name(s),address(es)and phone number(s)along with their certificate(s)of
insurance. Limited Liability Companies(LLC)or Limited Liability Partnerships(LLP)with no employees other than the
members or partners,are not required to carry workers'compensation insurance. If an LLC or LLP does have
employees,a policy is required. Be advised that this affidavit may be submitted to the Department of Industrial
Accidents for confirmation of insurance coverage. Also be sure to sign and date the affidavit. The affidavit should
be returned to the city or town that the application for the permit or license is being requested,not the Department of
Industrial Accidents. Should you have any questions regarding the law or if you are required to obtain a workers'
compensation policy,please call the Department at the number listed below. Self-insured companies should enter their
self-insurance license number on the appropriate line.
City or Town Officials
Please be sure that the affidavit is complete and printed legibly. The Department has provided a space at the bottom
of the affidavit for you to fill out in the event the Office of Investigations has to contact you regarding the applicant.
Please be sure to fill in the permit/license number which will be used as a reference number. In addition,an applicant
that must submit multiple permit/license applications in any given year,need only submit one affidavit indicating current
policy information(if necessary)and under"Job Site Address"the applicant should write"all locations in (city or
town)"A copy of the affidavit that has been officially stamped or marked by the city or town may be provided to the
applicant as proof that a valid affidavit is on file for future permits or licenses. A new affidavit must be filled out each
year.Where a home owner or citizen is obtaining a license or permit not related to any business or commercial venture
(i.e.a dog license or permit to bum leaves etc.)said person is NOT required to complete this affidavit.
The Department's address,telephone and fax number:
The Commonwealth of Massachusetts
Department of Industrial Accidents
1 Congress Street, Suite 100
Boston,MA 02114-2017
Tel. #617-727-4900 ext. 7406 or 1-877-MASSAFE
Fax#617-727-7749
Revised 02-23-15 www.mass.gov/dia
OMMONWEALTH OF HUSfTT&; .
DIC r • • • •
a wr SHEET METAL WORKIIS
z
OF Ma N .sem as 71190BER ISSUE,$THS FOLLOWlN0..iOENSE
NUNS_ rl,;V lTED-- .
sa a {J 97-1
' AARON MORIN
t5 sm M is
14d NEST ST i
`sa
WE TJ MA O�LS�SO :
9140 WEST ST
W HATFIELD,MA 01088.9500
S DD 10.15.1015 Hw 07.15-7009
S33 01/28/201'9 332632
. fL-'l0 5,, _.�
ons NWE ,TH OF
s �
Co.,�i�
MAPS? .
QiiF► _• ENSE
HEE I =,��tl i
issLiEs. :FOL.L. ING L i As ,wig+OF
Y. 1{tt. Dow n i llume t
E 1CTEp: IIS NONE S 9052964
�
AARaf• V G1RiN
M- tc ltct Vi#'
N 1 i
sT HA=!F 1 q } yea >
' "' !i ( n1A0WE&T 6T
t�Hai s, W HATAELD,MA 81888.9508
ifq 2 •,$ 2442
•.s �` .•.• 5ddNf•152018flev0T•152068
tl tl4•
1
t�
f'
f
1t
e
e- A,-F a c
c&-tu-ox- fo& � �I"'--
�I � A o m5
5005743-YTG-C-0815
® DESCRIPTION
M These indoor coils are designed to be installed with UPG
YOR furnaces or modular air handlers and matched with UPG
cooling and heat pump outdoor units. All coil models are
available as"flex-coil"units without a factory installed metering
device. Flex-coil models allow these coils to be used with R-
410A or R-22 for added flexibility to meet refrigerant system
choice. A piston or TXV metering device should be installed in
the field to meet your system requirements.
CF Models, Full Case Coils-Full cased coils are suitable for
TECHNICAL GUIDE use in upflow or downflow applications.
CM Models, Multi-Position Coils -CM coils have the added
ADD -ON COILS flexibility that allow them to be installed in any position-upflow,
FOR USE WITH SPLIT-SYSTEM downflow, or horizontal (right or left). This coil can be easily
installed with a UPG furnace or modular air handler in any
COOLING & HEAT PUMPS configuration.
MODELS: CF, CM, CU CU Models, Uncased Coils - These coils are designed for
installation on top of upflow furnaces, and they are to be used
600-2000 CFM 1.5-5 TON COILS for upflow only applications. The uncased coils require field
modification of the furnace duct for the coil installation.
FEATURES
RC2 - Rigid Case Construction interior endoskeleton for
structural support,flush side,and locks in insulation.
Powder-painted-G30 galvanized steel case provide a coated
edge that resists corrosion and rust creep.
MaxAlloyTM Coil - Long life aluminum coils built to deliver
lasting performance,efficiency and reliability.
UPFLOW Quality Construction - Structural components are made of
UNCASED Aluminum or G90 galvanized steel to prevent corrosion.
Cu Improved Insulation Design - Single piece with no external
screws to reduce thermal transmission paths to prevent
sweating. Foil faced insulation for ease of cleaning.
Thermostatic Expansion Valve - Bolt-on TXV provides easy
installation to convert the indoor coil to the required refrigerant
that does not require brazing to replace or install.Some models
are available with factory installed TXVs.
' Case Depth - These models have 20.5" casing which provide
UPFLOW/DOWNFLOW FULL CASED ease of attic access and tight applications.
FULL CASED MULTI-POSITION
CF CM Thermoset Drain Pan -Positive slope for drainage to reduce
cause for potential mold or contaminants.
ACCESSORIES
AL
Refer to Price Manual for specific model numbers.
Prem TXV Kits-Thermal expansion valve kits are available for flex-
coil applications with R-410A refrigerant. All TXV kits are non-
braze.All connections are bolt-on including the valve assembly
and equalizer tube.No orifice or any other metering device is to
AMERICAN ® be used in conjunction with the TXV.
QUALITY P �'6'.' citirx Partial Case—Available to be used with CU coils in four widths.
DESIGNED,ENQNEEEED A Iso soon This option is intended for upflow applications where height
ASSEMBLED N,THE USA C u$ Certified Quality limitations in the application prevent the installation of full cased
- Management System coils. The partial case design allows the top section of the
indoor coil to be installed in the duct or plenum.
Due to continuous product improvement, Coil Casing Without Coil -Coil casings are available in four
specifications are subject to change without notice. widths that can be installed with the furnace or modular air
handler during initial installation.This option is available to allow
Visit us on the web at: the installer the flexibility to add the coil at a later date without
www.upgnet.com and www.york.com duct modifications.
UVC Germicidal Light - The UVC technology effectively
Additional rating information can be found at: prevents mold, bacteria, and other microorganisms that
WWW.ahridirectory.org develop in air handling systems. The UVC Light Kit provides
safe, continuous cleaning while actually saving money by
reducing HVAC system maintenance and energy consumption.
FOR DISTRIBUTION USE ONLY-NOT TO BE USED AT POINT OF RETAIL SALE
400991-YTG-E-0210
12YORIC
DESCRIPTION
These compact units employ induced combustion, reliable hot
surface ignition and high heat transfer aluminized tubular heat
exchangers. The units are factory shipped for installation in
upflow or horizontal applications and may be converted for
Heating and Air Conditioning downflow applications.
These furnaces are designed for residential installation in a
TECHNICAL GUIDE basement, closet, alcove, attic, recreation room or garage and
95.5% SINGLE STAGE are also ideal for commercial applications. All units are factory
GAS-FIRED RESIDENTIAL assembled, wired and tested to assure safe dependable and
economical installation and operation.
MULTI-POSITION GAS FURNACES These units are Category IV listed and may be vented either
MODELS: TG9S through side wall or roof applications using approved plastic
NATURAL GAS combustion air and vent piping.
40-130 MBH INPUT FEATURES
• Easily applied in upflow,horizontal left or right,or downflow
installation with minimal conversion necessary.
• Compact,easy to install,ideal height 33"tall cabinet.
Blower-off delay for cooling SEER improvement.
pgt Easy access to controls to connect power/control wiring.
Built-in,high level self diagnostics with fault code displays
standard on integrated control module for reliable operation.
• Low unit amp requirement for easy replacement application.
• Single wire twinning or staging feature available.
• All models are convertable to use propane(LP)gas.
• Electronic Hot Surface Ignition saves fuel cost with
increased dependability and reliability.
• 100%shut off main gas valve for extra safety.
• 4 speed,direct drive PSC motor.
• 24V,40 VA control transformer and blower relay supplied for
add-on cooling.
Hi-tech tubular aluminized steel primary heat exchanger.
• Secondary heat exchanger made of corrosion resistant
stainless steel materials.
Timed on,adjustable off blower capability for maximum com-
� fort.
Residetitial • Blower door safety switch.
I DOE 10 CFR Part 430
fso �dt' Solid removable bottom panel allows easy conversion.
�oREGISG� Airflow leakage less than 1%of nominal airflow at duct-
`pF1E0WRRRAMiFUCUMdVYFRS ISO9OO1
Gond H)onkmnlnCertified Quality blaster conditions.
�EfVERR pENpR IF OE Management system
Promises No knockouts to deal with,making installation easier.
• Movable duct connector flanges for application flexibility.
Due to continuous product improvement,specifications Quiet inducer operation.
are subject to change without notice. Inducer rotates for easy conversion of venting options.
Visit us on the web at www.york.com Fully supported blower assembly for easy access and
Additional rating information can be found at removal of blower.
WWW.ahridirectory.orq External air filters used for maximum flexibility in meeting
customers IAQ needs.
WARRANTY Protection included from air intake,exhaust vent,or conden-
Lifetime limited warranty on both heat exchangers to the orig- sate blockage.
inal purchaser;a 20-year limited warranty from original instal- Venting applications-may be installed as either 2-pipe
lation date to subsequent purchaser. (sealed combustion)or single-pipe vent(using indoor com-
10-year warranty on the heat exchanger in commercial appli- bustion air).
cations. No special vent termination required.
Standard 5-year limited Parts warranty. 1/4 turn knobs provided for easy door removal.
Extended 10-year limited parts warranty when product is Internal condensate trap design(patent pending)provides
registered online within 90 days of purchase for condensate management options,easy visual operation,
replacement or closing for new home construction. and is self-priming to prevent nuisance problems.
FOR DISTRIBUTION USE ONLY-NOT TO BE USED AT POINT OF RETAIL SALE
400991-YTG-E-021 0
LEFT SIDE FRONT RIGHT SIDE
Combustion Air Inlet Combustion Air Inlet
Condensate Drain Gas Pipe
(Downflow) Entry Gas Pipe oor Condensate Drain
Entry (Downflow)
Vent Outlet--.00Electrical Electrical
Entry Entry Vent Outlet
Condensate o
01, Drain m m 33 Condensate
® ® 23" >
� � Drain
Thermostat
Wiring o Thermostat
wiring Optional Return it ,4"
Cutout(Either side)
L
U 0 ,
L J J �
N - 29.---H I lam-A
-
- 29.5-
56"
23.6"-p 3"f-
Vent
Outlet
B Combustion B
Air Inlet C
.56"
56" 20" 0 i 24.25"- 0
SUPPLY END RETURN END
Cabinet&Duct Dimensions
Nominal Cabinet Cabinet Dimensions(inches) Approximate
Models Operating Weights
CFM(m3/min) Size
A B C Lbs
TG9SO40A08MP11 800 A 141/2 133/8 11 3/4 113
TG9SO60A10MP11 1000 A 141/2 133/8 113/4 118
TG9S060B12MP11 1200 B 171/2 163/8 131/4 122
TG9S080B12MP11 1200 B 17 1/2 163/8 143/4 126
TG9S080C16MP11 1600 C 21 197/8 161/2 136
TG9S100C16MP11 1600 C 197/8 181/4 142
TG9S100C20MP11 2000 C 21 197/8 181/4 145
TG9S120D16MP11 1600 D 241/2 233/8 213/4 153
TG9S120D20MP11 2000 D 241/2 233/8 213/4 156
TG9S130D20MP11 2000 D 241/2 233/8 No Hole 160
Ratings&Physical/Electrical Data
AlrTemp. Max.Outlet Max Min.wire Size
Input Output AFUE Blower Blower Total Unit
Models Rise Air Temp Over-Current (awg)@ 75 it
MBH MBH % °F °F HP Amps Size Protect Amps one way
TG95040A08MP11 40 38 95.5 30-60 160 1/3 4.8 11x8 15 8.0 14
TG9S060A10MP11 60 57 95.5 30-60 160 1/2 7.1 11x8 15 10.0 14
TG9SO60B12MP11 60 57 95.5 30-60 160 1/2 7.1 11x8 15 10.0 14
TG9S080B12MP11 80 76 95.5 35-65 165 1/2 7.1 11x8 15 10.0 14
TG9S080C16MP11 80 76 95.5 35-65 165 3/4 8.8 11x10 15 11.5 14
TG9SO8OC22MP11 80 76 95.5 35-65 165 1 14.5 11x11 20 17.0 12
TG9S100C16MP11 100 95 95.5 35-65 165 3/4 8.8 11x10 15 11.5 14
TG9S100C20MP11 100 95 95.5 35-65 165 1 14.5 11x11 20 17.0 12
TG9S120D16MP11 120 114 95.5 40-70 170 3/4 8.8 11x10 15 11.5 14
TG9S120D20MP11 120 114 95.5 35-65 165 1 14.5 11x11 20 17.0 12
TG9S130D20MP11 130 123.5 95.5 45-75 175 1 14.5 11x11 20 17.0 12
Annual Fuel Utilization Efficiency(AFUE)numbers are determined in accordance with DOE Test procedures.
Wire size and over current protection must comply with the National Electrical Code(NFPA-704atest edition)and all local codes.
The furnace shall be installed so that the electrical components are protected from water.
2 Johnson Controls Unitary Products
5146416-YTG-A-0815
R DESCRIPTION
� ' The YCD models are the latest iteration in our successful LX
Series split system air conditioner lineup. Optimized for the 13
SEER Regional Minimum Efficiency in the North US and Can-
YOR ada, these outdoor units are specifically designed to be
matched with Johnson Controls Unitary Products indoor coils,
furnaces, and air handlers to provide a complete system solu-
tion.
TECHNICAL GUIDE -NSE;^ AND GNADA
FEATURES
LX SERIES • Small Footprint - Minimum footprint for easier handling,
SPLIT SYSTEM . transportation,and installation.
• Easier Installation - Independent panels provide quick
AIR CONDITIONERS ORlnW""""""° access for unit setup. Installation time is reduced by easy
13 SEER— R-41 OA— 1 PHASE power and control wiring access. Options are provided for
indoor piston or TXV.The factory installed filter-drier and fac-
1.5 THRU 5 NOMINAL TONS tory charge for a 15-Ft lineset means less time spent brazing
MODELS: YCD18 THRU 60 and charging the system. The small base dimension and
reduced unit clearances make for easier retrofits.
• Accessible Information - QR code on unit provides quick
access to technical documents and warranty information.
�. • Durable Finish - The coated steel wire fan guard, coated
external fasteners, and pre-treated G90-equivalent galva-
nized steel chassis components resist corrosion and rust
creep.Champagne colored powdercoat paint further protects
external panels.
• Quality Coils -The high efficiency microchannel aluminum
coil is manufactured using an improved material system pro-
viding reliable performance and small unit size.
• Rugged Coil Protection-Coils are protected from mechan-
ical damage by a proven stamped steel coil guard design.
• Protected Compressor-Compressors are protected inter-
nally by a high pressure relief valve and a temperature sen-
sor, and externally by the system high pressure switch. The
liquid line filter-drier is factory installed to protect the com-
W1A*iO COIpressor against moisture and debris.
JM\hBSyMFq
• Reliable Operation -Ball bearing fan motors provide supe-
MIS„,eso���+� rior performance in extreme temperatures.
M7 OR _ • Environmentally Friendly - CFC-free R-410A refrigerant
AMERICAN QUALITY delivers environmentally friendly performance with zero
ozone depletion.
® DESGNE DIN THE ENGINEERED
& • Top Discharge-Warm air is blown up,away from the struc-
ISo 9001 ture and any landscaping and allows compact location on
Certified Quality C PUS multi-unit applications.
Management System • Low Operating Sound Levels-Developed using CFD and
Due to continuous product improvement,specifications FEA tools,the sturdy cabinet and top design provides sound
are subject to change without notice. performance of 77 dBA or lower.Compatible accessories for
Visit us on the web at further sound reduction are also available.
www.upgnetcom and www.york.com • Better Service Access - Diagonal base valves with open Y
Additional rating information can be found at access for low-loss fittings,single panel access to the electri-
wwmahridirectot .org cal controls,swing out control box for full comer access,and
removable fan guard allow easy access for unit mainte-
WARRANTY SUMMARY* nance.
Standard 5-Years limited parts warranty. • Agency Listed -Safety certified by CSA to UL 1995/CSA
Standard 10-Years limited compressor warranty. 22.2. Performance certified to ANSI/AHRI Standard 210/240
Extended 10-Years limited parts warranty when product is in accordance with the Unitary Small Equipment certification
registered online within 90 days of purchase for replacement program.
or closing for new home construction.
`Does not apply to R-22 models,3-Phase models,or Internet sales.
See Limited Warranty certificate in User's Information Manual for details.
FOR DISTRIBUTION USE ONLY-NOT TO BE USED AT POINT OF RETAIL SALE
5146416-YTG-A-0815
PHYSICAL AND ELECTRICAL DATA
MODEL YCD18B YCD24B YCD30B YCD368 YCD42B YCD48B CD60B
21(H,S) 21(H,S) 21(H,S) 21(H,S) 21(H,S) 21S 21S
Unit Supply Voltage
Normal Voltage Range 15T to 252
9.6 12.3 14.2 19.9 21.9 28.5
15 20 20 30 35 50
Min.Overcurrent Device Amps 3 15 15 15 20 25 30 35
Compressor Type Recip Recip Recip Recip Recip Scroll Scroll
Compressor Rated Load 7.0 9.2 10.7 14.7 16.5 21.8 26.4
Amps Locked Rotor 45.0 45.0 57.0 78.0 88.0 117 134
Crankcase Heater No No No No No No No
Factory External Discharge Muffler No No No No Yes No No
Factory Extemal Check Valve No No No No No No No
HS Kit Required with TXV 4 Yes* Yes* Yes* Yes* Yes* No No
Fan Diameter Inches 18 18 18 18 22 22 22
Rated HP 1/8 1/8 1/8 1/4 1/4 1/4 1/4
Fan Motor Rated Load Amps 0.80 0.80 0.80 1.50 1.30 1.30 1.30
Nominal RPM 1075 1075 1075 1100 850 850 850
Nominal CFM 1925 1950 2150 2575 2925 3225 3350
Face Area Sq.Ft. 8.26 9.78 11.07 12.37 12.22 13.83 17.37
Coil Rows Deep 1 1 1 1 1 1 1
Fins/Inch 23 23 23 23 23 23 23
Liquid Line Set OD(Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8 3/8
Vapor Line Set OD(Field Installed)5 3/4 3/4 3/4 3/4 7/8 7/8 1-1/8t
Unit Charge(Lbs.-Oz.)6 2-15 3-4 3-13 4-1 4-6 4-8 5-6
Charge Per Foot,Oz. 0.62 0.62 0.62 0.62 0.67 0.67 0.75
Operating Weight Lbs. 125 130 140 140 175 165 175
Models with"H"on the end of the model number are shipped with a Hard Start Kit installed at the factory.
1. Rated in accordance with AHRI Standard 110-2012,utilization range"A".
2. Dual element fuses or HACR circuit breaker.Maximum allowable overcurrent protection.
3. Dual element fuses or HACR circuit breaker.Minimum recommended overcurrent protection.
4. See Hard Start Kit Accessory Installation Manual for Hard Start Kit part number for each model.
5. The Unit Charge is correct for the outdoor unit,smallest matched indoor unit,and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet,add or subtract
the amount of refrigerant,using the difference In actual lineset length(not the equivalent length)multiplied by the per foot value.
6. For applications with non-standard vapor line sizes,see the"Applications&Accessories"section of this Technical Guide.
DIMENSIONS
C Dimensions Refrigerant Connection
Unit
Model (inches) Service Valve Size
A B C Liquid Vapor
YCD18B21(H,S) 23-1/2 24 24
YCD24B21(H,S) 26-3/4 24 24 3/4
YCD30B21(H,S) 30 24 24
A YCD36B21(H,S) 33-1/4 24 24 3/8
YCD42B21(H,S) 26-3/4 29-1/4 29-1/4 7/8
YCD48B21S 30 29-1/4 29-1/4
YCD60B21S 36-1/4 29-1/4 29-1/4 7/8$
t Adapter fitting must be field installed for the required 1-1/8"line set.
B All dimensions are in inches and are subject to change without notice.
Overall height is from bottom of base pan to top of fan guard.
A033�W, Overall length and width include screw heads.
Johnson Controls Unitary Products 3