The URL can be used to link to this page

11-001 (14) I hope that is provides the information that you require. If you have further questions or comments, please do not hesitate to contact me at 617-708-1071. 1 thank you for your attention to this matter. e ely, r t BCHOLM • ELTON 4W3 icholas Elton, Si Mass. Reg. Architect 4 4923 4 • All the horn/strobes alarms throughout the common spaces within the buildings will sound • All strobe alarms in bathrooms will be activated • Mini-horns in bedrooms and horn/strobes inside the living units. • The exterior beacon light will activate • The cellular notification function in the fire alarm control panel will activate to notify the third party alarm/fire monitoring company. The fire/alarm monitoring company will notify the nearest fire department. • The locations of the problem area will be digitally registered and appear on the annunciator panel at the building entry and on the fire alarm control panel. • When either fire protection low pressure switch, or fire protection tamper switch is activated, it will, in turn, activate the Fire Alarm Control Panel (FRCP) causing it to go into supervisory mode. At this point,the FACP will contact the monitoring company and the monitoring company will them follow Protocol Procedures. • When any one or more of the following occur: open-wire, short circuit, ground fault, or low battery,the FACP be activated causing it to go into trouble condition mode. At this point,the FACP will contact the monitoring company and the monitoring company will then follow Protocol Procedures. In the building, all public areas, including egress stairs will be equipped with alarm signaling hard-wired interconnected smoke detectors. These detectors will: • Sound fire alarm horn/strobe throughout the public and unit spaces within the building • Alert the Alarm/Fire monitoring company through a cellular notification connection in the Fire Alarm Control Panel. Under provision 780 CMR 8th Edition (2009 International Building Code with Massachusetts Amendments) 907.2.11.2 and 907.2.11.3, local smoke detectors will be located in each dwelling unit within six feet (b') of all bedrooms entries and all bedrooms shall also be equipped with a local smoke detector. These detectors will: • Sound an audible alarm within the living unit only • In hearing impaired units the alarm shall be horn/strobe alarms • These shall be interconnected within the living unit so that and detection by one detector will activate all alarms within the living unit. Local smoke detectors, including combination detectors, are hard-wired; and are required to have battery back-up. In the event of an emergency, all building occupants will leave the building through the egressway routes of unit exit doors. In the event of a loss of power, these interior and exterior egressways routes will be clearly delineated with emergency lighting and powered exit signage. 3 Fire Detection and Alarm System Components: Per 780 CMR S'h Edition (2009 International Building Code with Massachusetts Amendments) 907.2.9, 907.4.2.1, and 907.5,the entire building shall be equipped with a complete, hardwired, addressable fire detection and alarm system. This system will include: • Addressable fire alarm control panel in the electric/telecommunications closet in the mechanical area including connections telephone connection to allow for alarm monitoring company notification • Addressable annunciator panel at central entrance of the building • Exterior beacon light over central entry where annunciator is located. • Smoke detectors in common hallways, stairways, common areas,and storage. • Audible/visible alarms (horn/strobes) alarms in all common areas, hallways, stairs and one in each living unit. • Visible alarms (strobes) in all bathrooms in units designated for the hearing impaired. • The fire alarm strobe (and strobe/horns) come equipped with a tamper proof enclosure and 8 candela settings as follows; 15/15.75/30/75/95/110/135/185. These units are set by the contractor with direction and approval of the Fire Department prior to installation. • Mini-horns in all bedrooms. • Heat detector in mechanical room, electric room, crawl spaces and one in each living unit. • Heat detectors in common laundry • Pull stations at all shared exterior doors • Tie-ins to building fire protection/sprinkler system with flow, tamper, low pressure, and inspector valve connections. • Battery system to support and allow system to continue to function for the period of time stipulated in Massachusetts Building Code and NFPA requirements. This system and these items are all delineated in the appended drawings. Fire Detection System Location Map: At the annunciator panel and at the fire alarm control panel there will be plans of the entire building with the location of all fire detection and alarm components shown. This will be posted on the wall next to these two components of the system. Fire Detection and Alarm System Function and Operation: In the event that one of the following events occur: • Smoke activates one or more smoke detectors in any space • Heat detector is activated in any space • Any pull station is pulled at any common exterior door • The connections to the fire protection/sprinkler activates The smoke/fire detection/alarm system will function as follows: 2 ELTON + HAMPTON ARCHITECTS 4 March 2013 Housing for Veterans — Building D: Fire Detection and Alarm System Narrative 425 North Main Street, Leeds, MA ➢ Building Information, Use, Current Features, and Project Overview: The project includes the construction of a two story building containing twelve (12) residential units, and a common area with common laundries, wheelchair lift, storage, and electrical/mechanical area. The building is 7,025 gr. sq. ft.. In accordance with both CMR 24, and IBC(2009) - Section 907.2.9, the building fall under the requirements of R- 2—Multi-family Residential. The building at twelve (12) units and exceeds the six unit maximum and is being constructed as a 5B—Wood Frame Un-Protected system,with the required fire separations, means of egress, and fire detection alarm requirements stipulated in those above-stated codes, and NFPA requirements. The proposed scope of work includes adding the following features to the building: Carbon Monoxide Detections: Per 527 CMR 31, one carbon monoxide detector shall be installed in each location where there are fossil-burning systems or appliances, including mechanical room. There will also be one carbon monoxide detector placed in each living unit. The proposed location of the CO detector is placed in the unit hallways outside the bedroom within 10' of all bedroom doors, as is stipulated in 527 CMR 31.04(1)b. In accordance with 527 CMR 31 - Explanation of Carbon Monoxide function: When a Carbon Monoxide detector is activated, it will, in turn, activate the Fire Alarm Control Panel (FACP) causing it to go into separate and distinct supervisory mode. At this point, the FACP will contact the 3rd Party monitoring company; this 3)" Parry monitoring company will then follow Protocol Procedures which allows the fire department personnel to know that the CO detector has activated and that this must be investigated immediately, but will not set off the general alarm and will not fall into the normal supervisory protocol of permitting a delayed investigation. This is delineated in the appended drawings. Primary/Eastern Massachusetts Office: 103 Terrace Street Roxbury, MA 02120 tel. (617) 708-1071 NickgEltonHamptonArchitects.com Western Massachusetts Office: 104 West Street Sandisfield, MA. 01255 I hope that is provides the information that you require. If you have further questions or comments,please do not hesitate to contact meat 617-708-1071. I thank you for your attention to this matter. Since y, �5S y ELTO N Nicholas Elton, No.4923 Mass. Reg. Architect#4923 4 • All the horn/strobes alarms throughout the common spaces within the buildings will sound • All strobe alarms in bathrooms will be activated • Mini-horns in bedrooms and horn/strobes inside the living units. • The exterior beacon light will activate • The cellular notification function in the fire alarm control panel will activate to notify the third party alarm/fire monitoring company. The fire/alarm monitoring company will notify the nearest fire department. • The locations of the problem area will be digitally registered and appear on the annunciator panel at the building entry and on the fire alarm control panel. • When either fire protection low pressure switch, or fire protection tamper switch is activated, it will, in turn, activate the Fire Alarm Control Panel (FACP) causing it to go into supervisory mode. At this point,the FACP will contact the monitoring company and the monitoring company will them follow Protocol Procedures. • When any one or more of the following occur: open-wire, short circuit, ground fault, or low battery, the FACP be activated causing it to go into trouble condition mode. At this point, the FACP will contact the monitoring company and the monitoring company will then follow Protocol Procedures. In the building, all public areas,including egress stairs will be equipped with alarm signaling hard-wired interconnected smoke detectors. These detectors will: • Sound fire alarm horn/strobe throughout the public and unit spaces within the building • Alert the Alarm/Fire monitoring company through a cellular notification connection in the Fire Alarm Control Panel. Under provision 780 CMR 8th Edition (2009 International Building Code with Massachusetts Amendments) 907.2.11.2 and 907.2.11.3, local smoke detectors will be located in each dwelling unit within six feet(6') of all bedrooms entries and all bedrooms shall also be equipped with a local smoke detector. These detectors will: • Sound an audible alarm within the living unit only • In hearing impaired units the alarm shall be horn/strobe alarms • These shall be interconnected within the living unit so that and detection by one detector will activate all alarms within the living unit. Local smoke detectors, including combination detectors, are hard-wired; and are required to have battery back-up. In the event of an emergency, all building occupants will leave the building through the egressway routes of unit exit doors. In the event of a loss of power, these interior and exterior egressways routes will be clearly delineated with emergency lighting and powered exit signage. 3 Fire Detection and Alarm System Components: Per 780 CMR 8ih Edition (2009 International Building Code with Massachusetts Amendments) 907.2.9, 907.4.2.1, and 907.5, the entire building shall be equipped with a complete,hardwired, addressable fire detection and alarm system. This system will include: • Addressable fire alarm control panel in the electric/telecommunications closet in the mechanical area including connections telephone connection to allow for alarm monitoring company notification • Addressable annunciator panel at central entrance of the building • Exterior beacon light over central entry where annunciator is located. • Smoke detectors in common hallways, stairways, common areas, and storage. • Audible/visible alarms (horn/strobes) alarms in all common areas,hallways, stairs and one in each living unit. • Visible alarms (strobes) in all bathrooms in units designated for the hearing impaired. • The fire alarm strobe (and strobe/horns) come equipped with a tamper proof enclosure and 8 candela settings as follows; 15/15.75/30/75/95/110/135/185. These units are set by the contractor with direction and approval of the Fire Department prior to installation. • Mini-horns in all bedrooms. • Heat detector in mechanical room, electric room, crawl spaces and one in each living unit. • Heat detectors in common laundry • Pull stations at all shared exterior doors • Tie-ins to building fire protection/sprinkler system with flow,tamper, low pressure, and inspector valve connections. • Battery system to support and allow system to continue to function for the period of time stipulated in Massachusetts Building Code and NFPA requirements. This system and these items are all delineated in the appended drawings. Fire Detection System Location Map: At the annunciator panel and at the fire alarm control panel there will be plans of the entire building with the location of all fire detection and alarm components shown. This will be posted on the wall next to these two components of the system. Fire Detection and Alarm System Function and Operation: In the event that one of the following events occur: • Smoke activates one or more smoke detectors in any space • Heat detector is activated in any space • Any pull station is pulled at any common exterior door • The connections to the fire protection/sprinkler activates The smoke/fire detection/alarm system will function as follows: 2 ELTON + HAMPTON ARCHITECTS 4 March 2013 Housing for Veterans — Building C: Fire Detection and Alarm System Narrative 425 North Main Street, Leeds, MA ➢ Building Information, Use, Current Features, and Project Overview: The project includes the construction of a two story building containing twelve (12) residential units, and a common area with common laundries, wheelchair lift, storage, and electrical/mechanical area. The building is 7,025 gr. sq. ft.. In accordance with both CMR 24, and IBC(2009) - Section 907.19, the building fall under the requirements of R- 2—Multi-family Residential. The building at twelve(12) units and exceeds the six unit maximum and is being constructed as a 513 —Wood Frame—Un-Protected system, with the required fire separations, means of egress, and fire detection/alarm requirements stipulated in those above-stated codes, and NFPA requirements. The proposed scope of work includes adding the following features to the building: Carbon Monoxide.Detections: Per 527 CMR 31, one carbon monoxide detector shall be installed in each location where there are fossil-burning systems or appliances, including mechanical room. There will also be one carbon monoxide detector placed in each living unit. The proposed location of the CO detector is placed in the unit hallways outside the bedroom within 10' of all bedroom doors, as is stipulated in 527 CMR 31.04(1)b. In accordance with 527 CMR 31 -Explanation of Carbon Monoxide function: When a Carbon Monoxide detector is activated, it will, in turn, activate the Fire Alarm Control Panel (FACP) causing it to go into separate and distinct supervisory mode. At this point, the FACP will contact the 3ra Party monitoring company; this 3`a Party monitoring company will then follow Protocol Procedures which allows the fire department personnel to know that the CO detector has activated and that this must be investigated immediately,but will not set off the general alarm and will not fall into the normal supervisory protocol of permitting a delayed investigation. This is delineated in the appended drawings. Primary/Eastern Massachusetts Office: 103 Terrace Street Roxbury, MA 02120 tel. (617) 708-1071 Nick cy,EltonliamptonArchiteets.com Western Massachusetts Office: 104 West Street Sandisfield, MA. 01255 I hope that is provides the information that you require. If you have further questions or comments,please do not hesitate to contact meat 617-708-1071. 1 thank you for your attention to this matter. Sinc e Pr E!TON 4923 �. Nicholas Elton, Mass. Reg.Architect#4923 4 • All the horn/strobes alarms throughout the common spaces within the buildings will sound • All strobe alarms in bathrooms will be activated • Mini-horns in bedrooms and horn/strobes inside the living units. • The exterior beacon light will activate • The cellular notification function in the fire alarm control panel will activate to notify the third party alarm/fire monitoring company. The fire/alarm monitoring company will notify the nearest fire department. • The locations of the problem area will be digitally registered and appear on the annunciator panel at the building entry and on the fire alarm control panel. • When either fire protection low pressure switch, or fire protection tamper switch is activated, it will,in turn, activate the Fire Alarm Control Panel (FACP) causing it to go into supervisory mode. At this point, the FACP will contact the monitoring company and the monitoring company will them follow Protocol Procedures. • When any one or more of the following occur: open-wire, short circuit, ground fault, or low battery,the FACP be activated causing it to go into trouble condition mode. At this point, the FACP will contact the monitoring company and the monitoring company will then follow Protocol Procedures. In the building, all public areas, including egress stairs will be equipped with alarm signaling hard-wired interconnected smoke detectors. These detectors will: • Sound fire alarm horn/strobe throughout the public and unit spaces within the building • Alert the Alarm/Fire monitoring company through a cellular notification connection in the Fire Alarm Control Panel. Under provision 780 CMR 81h Edition (2009 International Building Code with Massachusetts Amendments) 907.2.11.2 and 907.2.11.3, local smoke detectors will be located in each dwelling unit within six feet(6') of all bedrooms entries and all bedrooms shall also be equipped with a local smoke detector. These detectors will: • Sound an audible alarm within the living unit only • In hearing impaired units the alarm shall be horn/strobe alarms • These shall be interconnected within the living unit so that and detection by one detector will activate all alarms within the living unit. Local smoke detectors, including combination detectors, are hard-wired; and are required to have battery back-up. In the event of an emergency, all building occupants will leave the building through the egressway routes of unit exit doors. In the event of a loss of power,these interior and exterior egressways routes will be clearly delineated with emergency lighting and powered exit signage. 3 Fire Detection and Alarm System Components: Per 780 CMR 8th Edition (2009 International Building Code with Massachusetts Amendments) 907.2.9, 907.4.2.1, and 907.5, the entire building shall be equipped with a complete, hardwired, addressable fire detection and alarm system. This system will include: • Addressable fire alarm control panel in the electric/telecommunications closet in the mechanical area including connections telephone connection to allow for alarm monitoring company notification • Addressable annunciator panel at central entrance of the building • Exterior beacon light over central entry where annunciator is located. • Smoke detectors in common hallways, stairways, common areas, and storage. • Audible/visible alarms (horn/strobes) alarms in all common areas, hallways, stairs and one in each living unit. • Visible alarms (strobes)in all bathrooms in units designated for the hearing impaired. • The fire alarm strobe (and strobe/horns) come equipped with a tamper proof enclosure and 8 candela settings as follows; 15/15.75/30/75/95/110/135/185. These units are set by the contractor with direction and approval of the Fire Department prior to installation. • Mini-horns in all bedrooms. • Heat detector in mechanical room, electric room, crawl spaces and one in each living unit. • Heat detectors in common laundry • Pull stations at all shared exterior doors • Tie-ins to building fire protection/sprinkler system with flow, tamper, low pressure, and inspector valve connections. • Battery system to support and allow system to continue to function for the period of time stipulated in Massachusetts Building Code and NFPA requirements. This system and these items are all delineated in the appended drawings. Fire Detection System Location Map: At the annunciator panel and at the fire alarm control panel there will be plans of the entire building with the location of all fire detection and alarm components shown. This will be posted on the wall next to these two components of the system. Fire Detection and Alarm System Function and Operation: In the event that one of the following events occur: • Smoke activates one or more smoke detectors in any space • Heat detector is activated in any space • Any pull station is pulled at any common exterior door • The connections to the fire protection/sprinkler activates The smoke/fire detection/alarm system will function as follows: 2 ZZ/ ELTON + HAMPTON ARCHITECTS 4 March 2013 Housing for Veterans — Building B: Fire Detection and Alarm System Narrative 425 North Main Street, Leeds, MA ➢ Building Information, Use, Current Features, and Project Overview: The project includes the construction of a two story building containing ten(10) residential units, and a common area with common laundries, wheelchair lift, storage, and electrical/mechanical area. The building is 6,052 gr. sq. ft.. In accordance with both CMR 24, and IBC(2009) - Section 907.2.9, the building fall under the requirements of R- 2—Multi-family Residential. The building at ten (10) units and exceeds the six unit maximum and is being constructed as a 5B—Wood Frame—Un-Protected system, with the required fire separations, means of egress, and fire detection/alarm requirements stipulated in those above-stated codes, and NFPA requirements. The proposed scope of work includes adding the following features to the building: Carbon Monoxide Detections: Per 527 CMR 31, one carbon monoxide detector shall be installed in each location where there are fossil-burning systems or appliances, including mechanical room. There will also be one carbon monoxide detector placed in each living unit. The proposed location of the CO detector is placed in the unit hallways outside the bedroom within 10' of all bedroom doors, as is stipulated in 527 CMR 31.04(1)b. In accordance with 527 CMR 31 - Explanation of Carbon Monoxide function: When a Carbon Monoxide detector is activated,it will, in turn, activate the Fire Alarm Control Panel (FACP) causing it to go into separate and distinct supervisory mode. At this point, the FACP will contact the 3`d Party monitoring company; this 3"d Party monitoring company will then follow Protocol Procedures which allows the fire department personnel to know that the CO detector has activated and that this must be investigated immediately,but will not set off the general alarm and will not fall into the normal supervisory protocol of permitting a delayed investigation. This is delineated in the appended drawings. Primary/Eastern: Massachusetts Office: 103 Terrace Street Roxbury, MA 02120 tel. (6 17) 708-1071 Nick c�EltonHamptonArchitects.com Western Massachusetts Office: 104 West Street Sandisfield, MA. 01255 I hope that is provides the information that you require. If you have further questions or comments,please do not hesitate to contact meat 617-708-1071. I thank you for your attention to this matter. Since ly, HXHOM ELTON BM 4W Nicholas Elton, , Mass. Reg.Architect# 4923 4 • All the horn/strobes alarms throughout the common spaces within the buildings will sound • All strobe alarms in bathrooms will be activated • Mini-horns in bedrooms and horn/strobes inside the living units. • The exterior beacon light will activate • The cellular notification function in the fire alarm control panel will activate to notify the third party alarm/fire monitoring company. The fire/alarm monitoring company will notify the nearest fire department. • The locations of the problem area will be digitally registered and appear on the annunciator panel at the building entry and on the fire alarm control panel. • When either fire protection low pressure switch, or fire protection tamper switch is activated, it will,in turn, activate the Fire Alarm Control Panel (FACP) causing it to go into supervisory mode. At this point, the FACP will contact the monitoring company and the monitoring company will them follow Protocol Procedures. • When any one or more of the following occur: open-wire, short circuit, ground fault, or low battery, the FACP be activated causing it to go into trouble condition mode. At this point, the FACP will contact the monitoring company and the monitoring company will then follow Protocol Procedures. In the building, all public areas,including egress stairs will be equipped with alarm signaling hard-wired interconnected smoke detectors. These detectors will: • Sound fire alarm horn/strobe throughout the public and unit spaces within the building • Alert the Alarm/Fire monitoring company through a cellular notification connection in the Fire Alarm Control Panel. Under provision 780 CMR Bch Edition (2009 International Building Code with Massachusetts Amendments) 907.2.11.2 and 907.2.11.3, local smoke detectors will be located in each dwelling unit within six feet (6') of all bedrooms entries and all bedrooms shall also be equipped with a local smoke detector. These detectors will: • Sound an audible alarm within the living unit only • In hearing impaired units the alarm shall be horn/strobe alarms • These shall be interconnected within the living unit so that and detection by one detector will activate all alarms within the living unit. Local smoke detectors, including combination detectors, are hard-wired; and are required to have battery back-up. In the event of an emergency, all building occupants will leave the building through the egressway routes of unit exit doors. In the event of a loss of power, these interior and exterior egressways routes will be clearly delineated with emergency lighting and powered exit signage. 3 Fire Detection and Alarm System Components: Per 780 CMR 8th Edition (2009 International Building Code with Massachusetts Amendments) 907.2.9, 907.4.2.1, and 907.5, the entire building shall be equipped with a complete, hardwired, addressable fire detection and alarm system. This system will include: • Addressable fire alarm control panel in the electric/telecommunications closet in the mechanical area including connections telephone connection to allow for alarm monitoring company notification • Addressable annunciator panel at central entrance of the building • Exterior beacon light over central entry where annunciator is located. • Smoke detectors in common hallways, stairways, common areas, and storage. • Audible/visible alarms (hom/strobes) alarms in all common areas, hallways, stairs and one in each living unit. • Visible alarms(strobes) in all bathrooms in units designated for the hearing impaired. • The fire alarm strobe (and strobe/horns) come equipped with a tamper proof enclosure and 8 candela settings as follows; 15/15.75/30/75/95/110/135/185. These units are set by the contractor with direction and approval of the Fire Department prior to installation. • Mini-horns in all bedrooms. • Heat detector in mechanical room, electric room, crawl spaces and one in each living unit. • Heat detectors in common laundry • Pull stations at all shared exterior doors • Tie-ins to building fire protection/sprinkler system with flow, tamper, low pressure, and inspector valve connections. • Battery system to support and allow system to continue to function for the period of time stipulated in Massachusetts Building Code and NFPA requirements. This system and these items are all delineated in the appended drawings. Fire Detection System Location Map: At the annunciator panel and at the fire alarm control panel there will be plans of the entire building with the location of all fire detection and alarm components shown. This will be posted on the wall next to these two components of the system. Fire Detection and Alarm System Function and Operation: In the event that one of the following events occur: • Smoke activates one or more smoke detectors in any space • Heat detector is activated in any space • Any pull station is pulled at any common exterior door • The connections to the fire protection/sprinkler activates The smoke/fire detection/alarm system will function as follows: 2 ELTON + HAMPTON ARCHITECTS 4 March 2013 Housing for Veterans — Building A: Fire Detection and Alarm System Narrative 425 North Main Street, Leeds, MA ➢ Building Information, Use, Current Features, and Project Overview: The project includes the construction of a two story building containing ten (10) residential units, and a common area with common laundries, wheelchair lift, storage, and electrical/mechanical area. The building is 6,052 gr. sq. ft.. In accordance with both CMR 24, and IBC(2009) - Section 907.2.9,the building fall under the requirements of R- 2—Multi-family Residential. The building at ten (10)units and exceeds the six unit maximum and is being constructed as a 513—Wood Frame—Un-Protected system, with the required fire separations,means of egress, and fire detection/alarm requirements stipulated in those above-stated codes, and NFPA requirements. The proposed scope of work includes adding the following features to the building: Carbon Monoxide Detections: Per 527 CMR 31, one carbon monoxide detector shall be installed in each location where there are fossil-buming systems or appliances, including mechanical room. There will also be one carbon monoxide detector placed in each living unit. The proposed location of the CO detector is placed in the unit hallways outside the bedroom within 10' of all bedroom doors, as is stipulated in 527 CMR 31.04(1)b. In accordance with 527 CMR 31 - Explanation of Carbon Monoxide function: When a Carbon Monoxide detector is activated, it will, in turn, activate the Fire Alarm Control Panel (FACP) causing it to go into separate and distinct supervisory mode. At this point, the FACP will contact the 3rd Party monitoring company; this 3rd Party monitoring company will then follow Protocol Procedures which allows the fire department personnel to know that the CO detector has activated and that this must be investigated immediately,but will not set off the general alarm and will not fall into the normal supervisory protocol of permitting a delayed investigation. This is delineated in the appended drawings. Primary/Eastern Massachusetts Office: 103 Terrace Street Roxbury, MA 02120 tel. (617) 708-1071 NickLa EltonHamptonArchitects.com Western Massachusetts Office: 104 West Street Sandisfield, MA. 01255 1. REDUCED PRESSURE BACKFLOW PREVENTOR INSTALL HORIZONTALLY 36"TO 48"ABOVE FLOOR AND 12" MIN. FROM ANY WALL 2. DOUBLE CHECK VALVE ASSEMBLY (HORIZ.) INSTALL 36"TO 48"ABOVE FLOOR AND 12" MIN. FROM ANY WALL 3. VERTICAL DOUBLE CHECK VALVE ASSEMBLY(VERT.) INSTALL 12" MIN FROM ANY WALL TO SYSTEM it 0 ® 0 1 -6" T G GALV. 1'-0" CROSS CONNECTION PLAN PIPE STAND (mil FACILITY/OWNER: VA CENTRAL WESTERN MASS.HEALTHCARE SYSTEM 2" - AMES 20008 BACKFLOW W/ GR. ADDRESS: 421 N MAIN ST. LEEDS, MA 01053 BALL VALVES AND TAMPER SW. 421 NORTH MAIN ST LEEDS, MA SP NUMBER: NIA DCVA DETAIL COVENANT FIRE PROTECTION PREPARER: JASON KAHAN P.E. 62 WEST BROOK ST. SCALE: NTS MANCHESTER, NH 03101 855.517.7621 DATE: 2.14.2013 City of Northampton Department of Public Works Division of Water Supply 125 Locust Street Northampton,MA 01060 Baeldlow Prevention Device Design Data Sheet Application for Installation Owner's name r (' S 44 L4-717 Address I e'A 1 i Telephone number Facility Name Address LI V,il-'fL i I Le Contact person/egent Telephone number of facility contact person I i New facility Y/ Existing facility—L General description for the need of the installation of a backilow device Device Data Manufacturer name M S Model No. fi RPBP �Wd or Double Check Valves � Size Hat or cold water unit d By-pass arrangement;Yes or No Bract location of device ,. 4. M Water ddogwn steam of device Gate val t!V Ball valve Butterfly valve Plana and Spare Parts Required Ag jo4ation conUgggr is rc onsible for MMplyjng a Spam rraltM idt fQr cachdeviee A hilly labeled,detailed schematic of the potable and nots potable water piping immediately surroundipe the baWow prevention device installation showing: 1. Height above floor of the device 2. Distance from wall of the device 3. Type of chemical(s)used(if any)and the type of equipment upstream,and dower of the device Please note block:The schematic drawing must be at least 8 /,by 11 inches with the following information in the competed dde block. Submittod by. Plumber's signature: Plumber's license#: Owner/agent signature: Date: All information listed above must be included on schematic drawing: In addition,a fee of$65.00, made 6-4Yjkbie to the City of Northamotott for eacj3 dev ce aaQlkation muft be spbmitted to tbg D. '_W,before Pay anvl:gntio Abe ncocesaed. A permit form the plumbing inspector may be necessary for the installation of these devices. Approvals or denials of this application will be sent directly to the owner. If you have any questions, please call the Department of Public Works at 413-587-1570, Official DPW use only: Approval: Denial: Job: HOUSING FOR VETERANS Device Graphs Pressure vs. Flow Function Design Area: 1; Supply Ref.: W1; Supply Name:W1 ulo 95 — Y 90 _ 85 80-- 75 ............. , --------__ 70 „ 65 _ COL. 60 55_ U)o 50: _._........ > to d 45 (L 40 ._.... a 30 10- __-..._. _. _._._ _.... ___. ;.._.. _.._. __.... ....__ _.._.. 0` c ^ O O ^ ^ p C C C C C Flow,gpm Pressure Loss Function Design Area: 1; BFP Ref.: 0215 (Ames2000B, Size = 2) 7.69- 6.61)-- 5.7 psi @ 59.6 gpm 5.69 d 4.69_ 3 W fn N 3.69- a 2.61) . ___ 1.69_ 0119 Flow,gpm File:C:\Users\Vasilis\appdata\local\temp\leeds ma_side_FP2_1_1_6044.sv$ Date 1/16/2013 Copyright©2002-2012 Tyco Fire Protection Products Page 10 Job: HOUSING FOR VETERANS Hydraulic Calculations PIPE INFORMATION Path No: 4 S4 40.5 4.2 15.4 1 1X(BM.Tee-Br)=5 21.29 150 13.5 0004 21.5 15.4 1.101 2x(BM.90)=10 16 0.0419 8.2 lx(BM.Tee-Run)=1 37.29 1.6 0004 23.3 • Pressures are balanced to a high degree of accuracy. Values may vary by 0.1 psi due to display rounding. • Maximum Velocity of 10.35 ft/s occurs in the following pipe(s): (0005-0004) File:C:\Users\Vasilis\appdata\local\temp\leeds ma_side_FP2_1_1_6044.sv$ Date 1/16/2013 Copyright©2002-2012 Tyco Fire Protection Products Page 9 Job: HOUSING FOR VETERANS Hydraulic Calculations PIPE INFORMATION Node 1 Elev 1 K-Factor 1 Flow added (q) Nominal ID Fittings L C Factor total (Pt) Node 2 Elev 2 K-Factor 2 Total flow (Q) Actual ID quantity x (name) = length F Pf per ft elev (Pe) NOTES T frict (Pf) (ft) (gpm/psilh) (gpm) (in) (ft) (ft) (psi) (psi) Path No: 1 S2 40.5 4.2 14.4 1 1x(BM.Tee-Run)=1 29 150 11.8 0012 21.5 14.4 1.101 2x(BM.Tee-Br)=10 26 0.0369 8.2 3x(BM.90)=15 55 2 0012 21.5 14.5 1 2x(BM.90)=10 7.02 150 22 0022 21.5 28.9 1.101 10 0.1339 0 17.02 2.3 0022 21.5 0 1.5 1x(BM.Tee-Run)=1 22.39 150 24.3 0015 12 28.9 1.598 2x(BM.90)=16 17 0.0218 4.1 39.39 0.9 0015 12 30.7 1.5 2x(BM.90)=16 65.52 150 29.3 0064 3 59.6 1.598 2x(BM.Tee-Run)=2 26 0.0835 3.9 1x(BM.Tee-Br)=8 91.52 7.6 0064 3 0 2 lx(coupling)=1.3 1.14 150 40.8 0065-0 3 59.6 2.003 1.3 0.0278 0 2.43 0.1 0065-0 3 0 2 1.63 0 40.9 Ames2000B 0065-I 3 59.6 0 0 3.5122 0 1.63 5.7 0065-I 3 0 2 lx(us.90)=6.48 11.21 150 46.6 0067 -5 59.6 2.003 lx(BM.90)=10 16.48 0.0278 3.5 27.69 0.8 0067 -5 0 4 2x(us.90)=36.66 1039.1 140 50.8 W1 -5 59.6 4.3 1x(us.Tee-Br)=36.66 3 0.0008 0 73.31 0.9 1112.4 4 W1 51.7 Path No: 2 S1 40.5 4.2 14.5 1 2x(BM.Tee-Br)=10 24.67 150 11.9 0012 21.5 14.5 1.101 3x(BM.90)=15 26 0.0373 8.2 1x(BM.Tee-Run)=1 50.67 1.9 0012 22 Path No: 3 S3 40.5 4.2 15.3 1 2x(BM.Tee-Run)=2 25.63 150 13.3 0004 21.5 15.3 1.101 2x(BM.90)=10 17 0.0413 8.2 1X(BM.Tee-Br)=5 42.63 1.8 0004 21.5 15.4 1 1x(BM.Tee-Br)=5 0.96 150 23.3 0005 21.5 30.7 1.101 5 0.1501 0 5.96 0.9 0005 21.5 0 1.5 1X(BM.Tee-Br)=8 16.38 150 24.2 0015 12 30.7 1.598 2x(BM.90)=16 24 0.0245 4.1 40.38 1 0015 29.3 File:C:\Users\Vasilis\appdata\local\temp\leeds ma_side_FP2_1_1_6044.sv$ Date 1/16/2013 Copyright©2002-2012 Tyco Fire Protection Products Page 8 Job:HOUSING FOR VETERANS Hydraulic Calculations!Fluid Delivery Time Analysis Node Data Node# Type K-Fact. Discharge Coverage Tot. Pres. Req. Pres. Elev Hgroup Open/Closed Overdischarge Density Elev. Pres. Req. Discharge gpm/psiVz gpm ft2 psi psi ft gpm gpm/ft Z psi gpm S2 Overhead Sprinkler 4.2 14.4 144 11.8 11.8 40.5 HEAD Open 0 0.1 -19.7 14.4 S1 Overhead Sprinkler 4.2 14.5 144 11.9 11.8 40.5 HEAD Open 0.1 0.101 -19.7 14.4 S3 Overhead Sprinkler 4.2 15.3 144 13.3 11.8 40.5 HEAD Open 0.9 0.106 -19.7 14.4 S4 Overhead Sprinkler 4.2 15.4 144 13.5 11.8 40.5 HEAD Open 1 0.107 -19.7 14.4 0012 Node 22 21.5 NODE -11.5 0004 Node 23.3 21.5 NODE -11.5 0005 Node 24.2 21.5 NODE -11.5 0022 Node 24.3 21.5 NODE -11.5 0015 Node 29.3 12 NODE -7.4 0064 Node 40.8 3 NODE -3.5 0065-0 Node 40.9 3 NODE -3.5 0065-I Node 46.6 3 NODE -3.5 0067 Node 50.8 -5 NODE 0 W 1 Supply -59.6 51.7 -5 SUPPLY 0 File:C:\Users\Vasilis\appdata\local\temp\leeds ma_side_FP2_1_1_6044.sv$ Date 1/16/2013 Copyright©2002-2012 Tyco Fire Protection Products Page 7 Job : HOUSING FOR VETERANS Hydraulic Analysis for : 1 Graph Labels Values Label Description Flow (gpm) Pressure (psi) S1 Supply point#1 -Static 0 90 S2 Supply point#2-Residual 1000 88 D1 Elevation Pressure 0 19.7 D2 System Demand 59.6 51.7 D3 System Demand+Add.Out.Hose 159.6 51.7 Curve Intersections & Safety Margins Intersection Safety Margin Curve Name Pressure (psi) Flow m Pressure si @Flow m (P ) (gpm) (P ) (gpm) Supply 90 91.3 38.3 159.6 Open Heads Required Calculated Head Ref. Head Type Coverage K-Factor Density Flow Pressure Density Flow Pressure (ft2) (gpm/psi/2) (gpm/ftz) (gpm) (psi) (gpm/ftz) (gpm) (psi) S1 Overhead 144 4.2 0.1 14.4 11.8 0.101 14.5 11.9 Sprinkler S2 Overhead 144 4.2 0.1 14.4 11.8 0.1 14.4 11.8 Sprinkler S3 Overhead 144 4.2 0.1 14.4 11.8 0.106 15.3 13.3 Sprinkler S4 Overhead 144 4.2 0.1 14.4 11.8 0.107 15.4 13.5 Sprinkler File:C:\Users\Vasilis\appdata\local\temp\leeds ma_side_FP2_1_1_6044.sv$ Date 1/16/2013 Copyright @ 2002-2012 Tyco Fire Protection Products Page 6 Job: HOUSING FOR VETERANS Hydraulic Analysis for : 1 f Supply f System Demand f Add.Out.Hose 100 S 87.614 90 70 60 p. D2 D3 ti 7 50 y d 40 _. 30 D1 20 _ 10 0 0 300 400 500 600 700 800 900 1000 1100 Flow, gpm File:C:\Users\Vasilis\appdata\local\temp\leeds ma_side_FP2_1 1_6044.sv$ Date 1/16/2013 Copyright©2002-2012 Tyco Fire Protection Products Page 5 Job: HOUSING FOR VETERANS Hydraulic Analysis for : 1 Calculation Info Calculation Mode Demand Hydraulic Model Hazen-Williams Fluid Name Water @ 60F (15.6C) Fluid Weight, (lb/ft3) N/A for Hazen-Williams calculation. Fluid Dynamic Viscosity, (lb•s/ftz) N/A for Hazen-Williams calculation. Water Supply Parameters Supply 1 : W1 Flow(gpm) Pressure(psi) 0 90 1000 88 Hoses Inside Hose Flow/Standpipe Demand(gpm) Outside Hose Flow(gpm) Additional Outside Hose Flow(gpm) 100 Other(custom defined) Hose Flow(gpm) ------------------------------------------------------------------------------------ Total Hose Flow(gpm) 100 Sprinklers Ovehead Sprinkler Flow(gpm) 59.6 InRack Sprinkler Flow(gpm) 0 Other(custom defined)Sprinkler Flow(gpm) 0 ------------------------------------------------------------------------------------ Total Sprinkler Flow(gpm) 59.6 Other Required Margin of Safety(psi) 0 W1 -Pressure(psi) 51.7 W1 -Flow(gpm) 59.6 Demand w/o System Pump(s) N/A File:C:\Users\Vasilis\appdata\local\temp\leeds ma_side_FP2_1_1_6044.sv$ Date 1/16/2013 Copyright @ 2002-2012 Tyco Fire Protection Products Page 4 Job:HOUSING FOR\/E7`ERANS Diagram (Ootimiaed H for r Design Area ; Node Labels: draulic Si Pipe Labels: Off Sir off r t Date 1/16/2013 Fite;G:lUserslVasiti"a ppdataV ovallternp�leeds ma Copyri,qht©20()2-2012 Tyco Fire p p e� p od 2 1 1_6Q44.sv$ ucts Page 3 HYDRAULIC CALCULATIONS for Job Information Project Name : HOUSING FOR VETERANS Contract No. : City: LEEDS, MA 01053 Project Location: 421 N MAIN ST. Date: 1/16/2013 Contractor Information Name of Contractor: CFP Address: 62 W BROOK ST. City: MANCHESTER, NH 03101 Phone Number: 855.517.7621 E-mail: INFO @COVENANTFIREPRO.COM Name of Designer: CFP Authority Having Jurisdiction: TOWN OF LEEDS Design Remote Area Name 1 Remote Area Location TOP FLOOR Occupancy Classification RESIDENTIAL Density(gpm/ft2) 0.1 Area of Application(ft2) 576 Coverage per Sprinkler(ft2) 144 Number of Calculated Sprinklers 4 In-Rack Demand(gpm) 0 Special Heads Hose Streams(gpm) 100 Total Water Required(incl.Hose Streams)(gpm) 159.6 Required Pressure at Source(psi) 51.7 Type of System Wet Volume-Entire System (gal) 802.2 gal Water Supply Information Date 11/2012 Location PUMP AND TANK HOUSE Source W1 Notes File:C:\Users\Vasilis\appdata\local\temp\leeds ma_side_FP2_1_1_6044.sv$ Date 1/16/2013 Copyright©2002-2012 Tyco Fire Protection Products Page 2 CALCULATION SUMMARY Project Name: HOUSING FOR VETERANS Project Location: 421 N MAIN ST. Drawing No. : City: LEEDS, MA 01053 Design Areas Design Area Calc. Mode Occupancy Area of Total Water Pressure @ Min. Min. Min. Calculated Hose Margin To Name (Model) Application Source Density Pressure Flow Heads Streams Source (ft2) (gpm) (psi) (gpm/ft2) (psi) (gPm) # (gpm) (Psi) 1 Demand (HW) RESIDENTIAL 576 159.6 90 0.1 11.8 14.4 4 100 38.3 �tti OF 144,9.kT 10 JASON CATALFO KAHAN OU FIRE PROTECTION ti N . GISTS �OfVAL 01 . 16 . 2013 File:C:\Users\Vasilis\appdata\local\temp\feeds ma_side_FP2_1_1_6044.sv$ Date 1/16/2013 Copyright©2002-2012 Tyco Fire Protection Products Pagel ONTENA, NT FIR E P R O T E C T I O N 62 West Brook St. Manchester, NH, 03101 C: 617.633.3533 0: 855.517.7621 4. The system is Light Hazard and the topmost floor has been hydraulically calculated. ii. Automatic sprinkler system control equipment location 1. The sprinkler system will have one zone. iii. Type/description and design, layout of the standpipe system 1. No standpipe required. iv. Fire department connection will be installed at the front of the building per LFD requirements v. Type, description and design layout of the fire protective signaling system 1. Local fire alarm system. To be field verified by Fire alarm contractor 2. All supervisory and trouble signals are to be relayed to a central station service provider. 4 C O V E TN%,4 N T FIRE P R O T E C T I O N 62 West Brook St. Manchester, NH,03101 C: 617.633.3533 0: 855.517.7621 3. Main drain 4. Fire alarm system including: each device, wiring supervision, wiring connection. Proper mounting of equipment, notification appliance, related control features, central station connection shall be checked. 5. Verification of fire stopping 6. Verification of equipment function signs, charts,tags. b. Sprinkler system i. The sprinkler system shall be tested per NFPA 13R-2007 including 200 PSI hydrostatic testing when required. c. Fire Protection Signaling System i. All fire protection systems shall be tested with all equipment ready for operation. The following testes shall be performed with all equipment and devices to be tested: 1. Control equipment 2. Batteries 3. Control panel trouble signals 4. Conductors 5. Initiating devices 6. Alarm notification devices d. Building and site Access i. The primary emergency vehicle access point is on North Main Street on site. The city hydrants are on the same side of the street of the subject address. ii. The main entry is located on North Main Street on site. e. Fire Hydrants i. Existing hydrants are on site and are to be confirmed to be in working conditions f. Type/description and design layout of the automatic sprinkler system i. The new sprinkler system will be installed per NFPA 13. 1. Spacing of sprinkler heads less than 16x16 FT'(Light) and residential 2. Sprinkler heads are quick response 3. The addition of sprinkler heads can still support the hydraulic information. 3 CC7VENI� NT FIRE PROTEC -IF IC3N 62 West Brook St. Manchester, NH, 03101 C: 617.633.3533 0: 855.517.7621 a. The building will have a new sprinkler system installed per NFPA 13R and per CMR 780 903.2.8. -1 b. Sprinkler spacing and position shall be per NFPA 13R for a Light hazard and residential areas. Spacing shall be less than 168 SF in Light Hazard areas and per Viking specification in residential areas for residential sprinkler heads spaced 16'x16'. c. The sprinkler system will be fed by a 2"fire service supplied by public water supply per MSBC 81h Edition. Fire service which will also be equipped with a backflow device to avoid backfeeding. d. The sprinkler system is to be monitored by a separate flow switch and must be confirmed e. The flow switches and tamper switches shall be connected the fire alarm control panel. 4. Testing Criteria a. General i. The contractor for both sprinkler and fire alarm shall be responsible for the coordination of all required acceptance testing and shall schedule a meeting with the fire inspector for review and verification at least five days in advance of the test acceptance date. ii. All fire protection systems applicable to the building shall be pre-tested for proper operation. iii. The fire protection systems shall be tested as a system with all equipment ready for operation. iv. The following personnel shall be on site the day of testing with one set of individual as-built drawings for each FP system if applicable. 1. General Contractor 2. Fire Protection Engineer of Record 3. Sprinkler contractor if applicable 4. Fire alarm contractor if applicable v. The Fire Department shall direct and witness all testing vi. The following test shall be performed with all equipment and devices to be tested on NEW installations. 1. Sprinkler flow, inspector's test valve 2. Tamper switches 2 C O X/ E r1%J FIR E PRC7 'TEC 'IF ION 62 West Brook St. Manchester, NH, 03101 C: 617.633.3533 0: 855.517.7621 Fire Protection System Narrative Report 421 North Main Street Leeds, MA This document addresses the specific fire protection aspects to the new construction of a multiple unit dwelling located at 421 North Main Street Leeds, MA and generally addresses the site access conditions. 1. Basis of Design,Sequence of Operation and Testing Criteria a. Basis of Design i. Building Description a. New single use building consisting of four separate structures. Building A: 6896 SF Building B: 6810 SF Building C: 8082 SF Building D: 8082 SF b. Principal use group: Residential (R-2) c. Construction is Type V ii. Scope of work 1. Install new sprinkler system in multiple buildings 2. Applicable Laws, Regulations and Standards a. The Massachusetts General Laws (Chapter 148: Fire Prevention) b. The Massachusetts State Building Code, 8th Edition (780 CMR Chapter 9) c. Board of Fire Prevention and Regulation (527 CMR Chapter 24: Fire Warning Systems Installed in Buildings within the Commonwealth of Massachusetts) d. NFPA 72, 2007 \jN OF A4,q e. N FPA 13R, 2007 ti o JASON M.C. 3. Sprinkler System KAHAN o FIRE PROTECTION 0.48388 1 9 c G/STIC SipNAL Captain Larry Therrien Fire Prevention Officer Northampton Fire Department 26 Carlon Dr. Northampton, MA 01060 June 4, 2014 Dear Mr. Larry Therrien, Soldier On, Inc.will be constructing a new 44 Unit Residential Complex in 4 wood framed buildings on the VAMC site at 421 North Main Street in Leeds, MA. The newly assigned address for this complex will be 425 North Main Street Leeds, MA. The primary program for this project to house formally homeless Unites States Veterans. Currently,the construction documents are being reviewed by the building department. I am submitting to you several items today for your review and inspection: (1) Fire Alarm Work Permit (1) Check for$80.00 to accompany Fire Alarm Work Permit made out to "City of Northampton" (1) Fire Suppression Work Permit (1) Check for$80.00 to accompany Fire Suppression Work Permit made out to "City of Northampton" (1) Check for$1557.90 for the Fire Department's Certificate of Occupancy Inspection (25,965 sq.ft. Project Area X $0.06 per sq.ft. =$1556.90 Total Inspection Fee) (1) Set of Required Construction Drawings a. Title Page and Table of Contents b. Site Plan c. Architectural Floor Plans d. Fire Protection Plans (Sprinklers) e. Fire Alarm Plans f. Modular Shop Drawings (1) Fire Alarm Narrative (1) Fire Protection (Sprinkler) Narrative and Calculations (1) Compact Disc with ALL Project Construction Drawings Please do not hesitate to contact me if you have any additional questions. Sincerely, Michael Valenti Soldier On, Inc. - Project Manager 2 Federico Drive, Suite 1 Pittsfield, MA 01201 T: (413).443.3537 x.111 F: (413).445.5376 E: mvalenti @sk-designgroup.com THE FIGHT DOESN'T END WHEN THEY GET HOME 41-9 NORTH(U,`*.J STREET *UILDING 6 LEER*.MA 01053 (413)582-3059 36U WEST HOUSATOG*C STREET PITTSFIELi*MA 01201 '413)236-5644 www.wesoldieron.org City of Northampton 212 Main Street, Northampton, MA 01060 Solid Waste Disposal Affidavit In accordance of the provisions of MGL c 40, S54, I acknowledge that as a condition of the building permit all debris resulting from the construction activity governed by this Building Permit shall be disposed of in a properly licensed solid waste disposal facility, as defined by MGL c 111 , S 150A. Address of the work: 421 North Main Street, Leeds MA 01053 The debris will be transported by: Amherst Trucking Valley Regional Recycling & Transfer Facility The debris will be received by: Building permit number: Name of Permit Applicant General Contractor: BBL Construction Services, LLC l Date Signature of Permit Applicant <C11 ` Initial Construction Control Document To be submitted with the building permit application by a Registered Design Professional Ulf for work per the 8u'edition of the Massachusetts State Building Code, 780 CMR,Section 107 Project Title:Housing for Veterans Date:25 April 2014 Property Address: 421 North Main Street,Leeds,MA.,01053 Project: Check(x)one or both as applicable:X New construction Existing Construction Project description:Forty-four(44)units of housing in four(4)two story residential buildings. The building areas are: 6,052 sf,5,863 sf,7,025 sf,and 7,025 sf. I,James McHugh,MA Registration Number:38572 Expiration date:31 August 2014,am a registered engineer and I have prepared or directly supervised the preparation of all design plans,computations and specifications concerning': Architectural Structural Mechanical Fire Protection Electrical X Fire Detection/Alarm for the above named project and that to the best of my knowledge,information,and belief such plans,computations and specifications meet the applicable provisions of the Massachusetts State Building Code,(780 CMR),and accepted engineering practices for the proposed project. I understand and agree that I(or my designee)shall perform the necessary professional services and be present on the construction site on a regular and periodic basis to: 1. Review,for conformance to this code and the design concept,shop drawings,samples and other submittals by the contractor in accordance with the requirements of the construction documents. 2. Perform the duties for registered design professionals in 780 CMR Chapter 17,as applicable. 3. Be present at intervals appropriate to the stage of construction to become generally familiar with the progress and quality of the work and to determine if the work is being performed in a manner consistent with the approved construction documents and this code. Nothing in this document relieves the contractor of its responsibility regarding the provisions of 780 CMR 107. When required by the building official,I shall submit field/progress reports(see item 3.)together with pertinent comments,in a form acceptable to the building official. Upon completion of the work,I shall submit to the building official a`Final Construction Control Document'. Enter in the space to the right a"wet"or e`� JAMES electronic signature and seal: = McHUGH c F PRa7ECTION No.�e572 Phone number:781-871-8277 Email: ibenaine(a,aol.com "A NAt Building Official Use Only Building Official Name: Permit No.: Date: Note 1.Indicate with an`x'project design plans,computations and specifications that you prepared or directly supervised.If`other'is chosen, provide a description. Version 06 11 2013 �r Initial Construction Control Document To be submitted with the building permit application by a. Registered Design Professional for work per the a edition of the Massachusetts State Building Code,780 CMR,Section 107 Project Title:Housing for Veterans Date:May 6,2014 Properly Address: 421 North Main Street,Leeds,MA.,01053 Project: Check(x)one or both as applicable:X New construction Existing Construction Project description:Forty-four(44)units of housing in four(4)two story residential buildings. The building areas are: 6,052 sf,5,863 s4 7,025 sf,and 7,025 sE I,Paul R Hartnett MA Registration Number: 30134 Expiration date:6-30-14,am a registered engineer, and I have prepared or directly supervised the preparation of all design plans,computations and specifications concerning': Architectural Structural Mechanical Fire Protection X Electrical Dwg Plumbing: for the above named project and that to the best of my knowledge,information,and belief such plans,computations and specifications meet the applicable provisions of the Massachusetts State Building Code,(780 CMR),and accepted engineering practices for the proposed project. I understand and agree that I(or my designee)shall perform the necessary professional services and be present on the construction site on a regular and periodic basis to: 1. Review,for conformance to this code and the design concept,shop drawings,samples and other submittals by the contractor in accordance with the requirements of the construction documents. 2. Perform the duties for registered design professionals in 780 CMR Chapter 17,as applicable. 3. Be present at intervals appropriate to the stage of construction to become generally familiar with the progress and quality of the work and to determine if the work is being performed in a manner consistent with the approved construction documents and this code. Nothing in this document relieves the contractor of its responsibility regarding the provisions of 780 CMR 107. When required by the building official,I shall submit field/progress reports(see item 3.)together with pertinent comments,in a form acceptable to the building official. Upon completion of the work,I shall submit to the building official a`Final Construction Control Document'. Enter in the space to the right a"wet"or electronic signature and seal: 4t got F"!r,\{i`�" Phone.number: 508-559-0418 Email: twbasso@aol.com Building official Use Only Building Official Name: Permit No.: Date: Note 1.Mc ate with an'x'project design plans,computations and specifications that you prepared or directly supervised.If'other'is chosen, provide a description. Version 06 11 2013 Initial Construction Control Document To be submitted with the building permit application by a Registered Design Professional for work per the 8th edition of the Massachusetts State Building Code, 780 CMR, Section 107 Project Title:Housing for Veterans Date:21 February 2014 Property Address: 421 North Main Street,Leeds,MA.,01053 Project: Check(x)one or both as applicable:X New construction Existing Construction Project description:Forty-four(44)units of housing in four(4)two story residential buildings. The building areas are: 6,052 sf,5,863 sf,7,025 sf,and 7,025 sf. I,Jason Catalfo Kahan,MA Registration Number:48388 Expiration date:31 August 2014,am a registered,fire protection engineer, and I have prepared or directly supervised the preparation of all design plans,computations and specifications concerningl: Architectural Structural Mechanical Fire Protection Electrical X Other:Fire Protection for the above named project and that to the best of my knowledge,information,and belief such plans,computations and specifications meet the applicable provisions of the Massachusetts State Building Code,(780 CMR),and accepted engineering practices for the proposed project. I understand and agree that I(or my designee)shall perform the necessary professional services and be present on the construction site on a regular and periodic basis to: 1. Review,for conformance to this code and the design concept,shop drawings,samples and other submittals by the contractor in accordance with the requirements of the construction documents. 2. Perform the duties for registered design professionals in 780 CMR Chapter 17,as applicable. 3. Be present at intervals appropriate to the stage of construction to become generally familiar with the progress and quality of the work and to determine if the work is being performed in a manner consistent with the approved construction documents and this code. Nothing in this document relieves the contractor of its responsibility regarding the provisions of 780 CMR 107. When required by the building official,I shall submit field/progress reports(see item 3.)together with pertinent comments,in a form acceptable to the building official Upon completion of the work,I shall submit to the building official a`Final Construction Control Document'. Enter in the space to the right a"wet"or electronic signature and seal: Phone number:855-517-7621 Email:ikahan cr.covenautfirepro.com RsGtg� �l= Building Official Use Only Building Official Name: Permit No.: Date: Note 1.Indicate with an`x'project design plans,computations and specifications that you prepared or directly supervised.If`other'is chosen, provide a description. Version 06 11 2013 Initial Construction Control Document To be submitted with the building permit application by a Registered Design Professional for work per the 8n'edition of the Massachusetts State Building Code, 780 CMR,Section 107 Project Title:Housing for Veterans Date:6 May 2014 Property Address: 421 North Main Street,Leeds,MA.,01053 Project: Check(x)one or both as applicable:X New construction Existing Construction Project description:Forty-four(44)units of housing in four(4)two story residential buildings. The building areas are: 6,052 sf,5,863 sf,7,025 sf,and 7,025 sE I,Peter Nicholas Elton MA Registration Number:4923 Expiration date:31 August 2014,am a registered design professional, and I have prepared or directly supervised the preparation of all design plans,computations and specifications concerning: X Architectural X Structural Mechanical Fire Protection Electrical Other: for the above named project and that to the best of my knowledge, information,and belief such plans,computations and specifications meet the applicable provisions of the Massachusetts State Building Code,(780 CMR),and accepted engineering practices for the proposed project. I understand and agree that I(or my designee)shall perform the necessary professional services and be present on the construction site on a regular and periodic basis to: 1. Review,for conformance to this code and the design concept,shop drawings,samples and other submittals by the contractor in accordance with the requirements of the construction documents. 2. Perform the duties for registered design professionals in 780 CMR Chapter 17,as applicable. 3. Be present at intervals appropriate to the stage of construction to become generally familiar with the progress and quality of the work and to determine if the work is being performed in a manner consistent with the approved construction documents and this code. Nothing in this document relieves the contractor of its responsibility regarding the provisions of 780 CMR 107. When required by the building official,I shall submit field/progress reports(see item 3.)together with pertinent comments,in a form acceptable to the building official. Upon completion of the work,I shall submit the bu' ng official a`Final Construction Control Document'. Enter in the space to the right a"wet"or IL electronic signature and seal: t I ELTON fft 4923 Phone number:617-7808-1071 Email:NickCa),eltonhamntonarchitects.com Building Official Use Only Building Official Name: Permit No.: Date: Note 1.Indicate with an`x'project design plans,computations and specifications that you prepared or directly supervised.If`other'is chosen, provide a description. Version 06 11 2013 Initial Construction Control Document To be submitted with the building permit application by a Registered Design Professional for work per the 8h edition of the Massachusetts State Building Code,780 CMR, Section 107 Project Title:Housing for Veterans Date:May 6,2014 Property Address: 421 North Main Street,Leeds,MA.,01053 Project: Check(x)one or both as applicable:X New construction Existing Construction Project description:Forty-four(44)units of housing in four(4)two story residential buildings. The building areas are: 6,052 sf,5,863 sf,7,025 sf,and 7,025 sf. I,Allan R Morris MA Registration Number: 13505 Expiration date: 6-15-14,am a registered engineer, and I have prepared or directly supervised the preparation of all design plans,computations and specifications concerning': Architectural Structural X Mechanical Fire Protection Electrical X Plumbing: for the above named project and that to the best of my knowledge,information,and belief such plans,computations and specifications meet the applicable provisions of the Massachusetts State Building Code,(780 CMR),and accepted engineering practices for the proposed project. I understand and agree that I(or my designee)shall perform the necessary professional services and be present on the construction site on a regular and periodic basis to: 1. Review,for conformance to this code and the design concept,shop drawings,samples and other submittals by the contractor in accordance with the requirements of the construction documents. 2. Perform the duties for registered design professionals in 780 CMR Chapter 17,as applicable. 3. Be present at intervals appropriate to the stage of construction to become generally familiar with the progress and quality of the work and to determine if the work is being performed in a manner consistent with the approved construction documents and this code. Nothing in this document relieves the contractor of its responsibility regarding the provisions of 780 CMR 107. When required by the building official,I shall submit field/progress reports(see item 3.)together with pertinent comments,in a form acceptable to the building official. Upon completion of the work,I shall submit to the building official a`Final Construction Control Document'. Enter in the space to the right a"wet"or electronic signature and seal: L � Phone number: 508-559-0418 Email: twbasso @aol.com Building Official Use Only Building Official Name: Permit No.: Date: Note 1.Indicate with an`x'project design plans,computations and specifications that you prepared or directly supervised.If`other'is chosen, provide a description. Version 06 11 2013 City of Northampton Massachusetts . �f I DEPARTMENT OF BUILDING INSPECTIONS nx ` 212 Main Street • Municipal BuildingJb re` Northampton, MA 01060 INSPECTOR Louis Hasbrouck Fax: 413-587-1272 Chuck Miller Building Commissioner Phone: 413-587-1240 Assistant Commissioner SECONDARY CONSTRUCTION CONTROL DOCUMENT (For professional Engineers/Architects responsible for a op rtion of a controlled project) Project Title: JJ6 L*(kV(q tDR V e7e R AN T Date:IL4 liq Project Location: '115 1jopm+ tAMAJ 5T, L%vs Map: U_Parcel Zone: gAZ% Scope of Project-.:F00 w VAnOO -r- 5 I-M (CIVIL) W aP K fM 4 LJ V 0 IT TZF5 1 D6AM4 L CD►'4Pt�E� In accordance with the Eighth edition Massachusetts State Building Code, 780 CMR Section 1007.6: , I, TA KE5 P\ . d CA U j6- '_�E Mass. Registration# 39%(03 - being a registered professional Engineer/Architect hereby CERTIFY that I have prepared or directly supervised the preparation of all design plans, computations and specifications concerning: [ ] Fire Protection [ ] Architectural Structural [ ] Mechanical [ ] Electrical C,Other(specify) '000 N UA-T V� i` 5 l� ( G L y I ie ) for the above named project and that to the best of my knowledge, such plans, computations and specifications meet the applicable provisions of the Massachusetts State Building Code, all acceptable engineering practices and all applicable Laws for the proposed project. Furthermore, I understand and AGREE that I shall perform the necessary professional services to determine that the above mentioned portions of the work proceed in accordance with the documents approved for the building permit. Upon completion of the work, I shall submit to the building official a final report as to the satisfactory Completion of the above mentioned work. t Si nature and e I R gist � essional ?� Day of t)WE 20 (seal) WORKERS CONDENSATION AND EIVPL.OYERS LIABILITY INSURANCE POLICY Liberi R Mutual• 1r,sU�ANCe INFORMATION PAGE 176 Berkeley Street soston,MA02116 Issued by The First Liberty Insurance Corporation (a stock company) 27359 Policy Number WC6-621-093961-014 Issuing Office Lewiston, ME Renewal Of WC2-621-093961-013 Issue Date 04/17/2014 Account Number 2-093961 Sub Account 0000 1. Insured and Mailing Address FEIN 14-1792632 BBL, LL P.O. Boar 12789 ALBANY NY '12212-2789 Risk ID 917185085 Status Limited Liability Company Other workplaces not shown above: See Item 4. Premium -Extension of Information Page 2, Policy Period: The policy period is from 04/0112014 to 0410112015 12:01 A.M. standard time at the Insured's mailing address. 3. Coverage A. Workers Compensation Insurance: Part One of the policy applies to the Workers Compensation Law of the states listed here: CT DE FL GA IA MA NE NJ NY NC PA RI SC TX B. Employers Liability Insurance: Part Two of the policy applies to work in each state listed in Item 3.A. The limits of our liability under Part Two are: Bodily Injury by Accident $ 1,000,000 each accident Bodily Injury by Disease $ 1,000,000 policy limit Bodily Injury by Disease $ 1.000,000 each employee C. Other States Insurance: Part Three of the policy applies to the states, if any, listed here: All States except those listed in Item 3.A and the States of: MD NH NU OH WA WY D. This policy includes these endorsements and schedules: See Item 3. Coverage D- Extension of Information Page 4. Premium: The premium for this policy will be determined by our Manuals of Rules, Classifications, Rates and Rating Flans. All information required below is subject to verification and change by audit. Classifications Cade Premium Basis Total Rate per$100 Estimated Annual Number Estimated Annual Remuneration of Remuneration Premium See Extension of Information Page Minimum Premium $1,250 (CT) Total Estimated Annual Premium Premium will be billed Annual Deposit Premium Deposit Tax/Surcharge/Assessment Producer 0002 012820 Countersigned by Authorized Rep. (FL) ARTHUR GALLAGHER RISK MANAGEMENT SERVICES INC 677 BROADWAY STE 401 ALBANY NY 12207 --.--. . - WC 0000 01 A ®1987 National Council on Compensation Insurance,Inc. WC 00 00 01 B (CA/NJ) Ed.07101/2011 All Rights Reserved Page 1 of 1 The Commonwealth of Massachusetts Department of Industrial Accidents 1i Office of Investigations A a I Congress Street, Suite 100 p� Boston, MA 02114-2017 www mass.gov/dia Workers' Compensation Insurance Affidavit: Builders/Contractors/Electricians/Plumbers Applicant Information Please Print Legibly Name (Business/Organization/Individual): BBL Construction Services, LLC Address: 302 Washington Ave Extension City/State/Zip:Albany, NY 12203 Phone #: 518-452-8200 Are you an employer? Check the appropriate box: Type of project(required): 1.0 I am a employer with 104 4. [] I am a general contractor and I 6. New construction employees (full and/or part-time).* have hired the sub-contractors 2.❑ I am a sole proprietor or partner- listed on the attached sheet. 7. ❑ Remodeling ship and have no employees These sub-contractors have g, ❑ Demolition working for me in any capacity. employees and have workers' 9. ❑ Building addition [No workers' comp. insurance comp. insurance.$ required.] 5. ❑ We are a corporation and its 10.❑ Electrical repairs or additions 3.❑ I am a homeowner doing all work officers have exercised their 11.❑ Plumbing repairs or additions myself. [No workers' comp. right of exemption per MGL 12.❑ Roof repairs insurance required.] t c. 152, §1(4),and we have no employees. [No workers' 13.❑ Other comp. insurance required.] *Any applicant that checks box#1 must also fill out the section below showing their workers'compensation policy information. t Homeowners who submit this affidavit indicating they are doing all work and then hire outside contractors must submit a new affidavit indicating such. $Contractors that check this box must attached an additional sheet showing the name of the sub-contractors and state whether or not those entities have employees. If the sub-contractors have employees,they must provide their workers'comp.policy number. I am an employer that is providing workers'compensation insurance for my employees. Below is the policy and job site information. Insurance Company Name: First Liberty Insurance Corp Policy# or Self-ins. Lic. #:WC2621093961014 Expiration Date:04/01/15 Job Site Address: 421 North Main Street City/State/Zip: Leeds, MA 01053 Attach a copy of the workers' compensation policy declaration page(showing the policy number and expiration date). Failure to secure coverage as required under Section 25A of MGL c. 152 can lead to the imposition of criminal penalties of a fine up to $1,500.00 and/or one-year imprisonment, as well as civil penalties in the form of a STOP WORK ORDER and a fine of up to$250.00 a day against the violator. Be advised that a copy of this statement may be forwarded to the Office of Investigations of the DI-A for insurance coverage verification. I do hereby certify un e p s and penalties of rjury t at the information provided above is true and correct 05/01/2014 Signature: Date: Phone#: 518-452-820 -- Official use only. Do not write in this area,to be completed by city or town official. City or Town: Permit/License # Issuing Authority(circle one): 1.Board of Health 2. Building Department 3. City/Town Clerk 4. Electrical Inspector 5. Plumbing Inspector 6.Other Contact Person: Phone#: Versionl.7 Commercial Building Permit May 15,2000 SECTION 10-STRUCTURAL PEER REVIEW(780 CMR 110.11) Independent Structural Engineering Structural Peer Review Required Yes ® No SECTION 11 -OWNER AUTHORIZATION -TO BE COMPLETED WHEN OWNERS AGENT OR CONTRACTOR APPLIES FOR BUILDING PERMIT 1, as Owner of the subject property hereby authorize --to act on my behalf, in all matters relative to work authorized by this building permit application. Signature of Owner Date James M. Scalise II -Owners Rep., Soldier On, Inc. as Owner/Authorized Agent hereby declare that the statements and information on the foregoing application are true and accurate,to the best of my knowledge and belief. Signed under the pains and penalties of perjury. James M. Scalise II Print Na -+ 06/04/2014 Signat e o Owner/Agent Date SECTI 1 -CONSTRUCTION SERVICES 10.1 Licensed Construction Supervisor: Not Applicable ❑ Name of License Holder: James M. Scalise II 39863 (PE) License Number S.K. Design Group 2 Federico Drive, Pittsfield, MA 01201 06/30/2014 Addres -1 Expiration Date ' ,(413) 443-3537 Signat Telephone SECTION 13-WORKERS'COMPENSATION INSURANCE AFFIDAVIT(M.G.L.c. 152,§25C(6)) Workers Compensation Insurance affidavit must be completed and submitted with this application. Failure to provide this affidavit will result in the denial of the issuance of the building permit. Signed Affidavit Attached Yes No 0 Version 1.7 Commercial Building Permit May 15,2000 SECTION 9-PROFESSIONAL DESIGN AND CONSTRUCTION SERVICES-FOR BUILDINGS AND STRUCTURES SUBJECT TO CONSTRUCTION CONTROL PURSUANT TO 780 CMR 116(CONTAINING MORE THAN 35,000 C.F.OF ENCLOSED SPACE) 9.1 Registered Architect . _ Not licable 13 Peter Nichol ton-Elton&Hampton Architects - - Name(Ragtstrant _ 4923 4 103 Terra St., xbury Crossing,MA FWstration Number Address (617)-708-1071 ` Expiration Date Signature Telephone 8.2 gogfskered Professional Engineer(s): Ci James M. Scalise II SK Design Group vil Site and Foundation_.__ .._.._._ ' )_ Name Area of Responsibility - 2 Federico Dr. Suite 1,Pittsfield,MAO 1201 39863 Addres ..s Registration Number ; 413) 443-3537- ' 6/30/2014. ...... sign Telephone Expiration Date Name Area of Responsibility Address Regl tion Number } Signature Telephone Expiration Date Name Area of Responsibility Address Registration Number Signature Telephone Expiration Date �F Name Area of Responsibility Address Registration Number i Signature Telephone Expiration Date 9.3 General Contractor BBL Construction Services,LLC Not Applicable❑ Comparmy Name: Tim Karl Respon le In Charge of OonstmCdon 302 Washington Ave Extension,Albany NY 12203 ` Address '(518)452-8200 Signature Talaph" Versionl.7 Commercial Building Permit May 15,2000 8. NORTHAMPTON ZONING * C OM TRLtHE-&6i V6 TER M tr Existing Proposed Required by Zoning This column to be fille by Building Departm Lot Size Frontage Setbacks Front Side L: L: Rear Building Height Bldg.Square Footage % Open Space Footage % (Lot area minus bldg&paved parking) #of Parkina S es Fil olume&Location A. Has a Special Permit/Variance/Finding ever been issued for/on the site? NO () DON'T KNOW ® YES IF YES, date issued: 12/19/2012 IF YES: Was the permit recorded at the Registry of Deeds? (CoN'PW6fj41VF- 'PERa l T> NO Q DON'T KNOW 0 YES e IF YES: enter Book 11644 Page 166 and/or Document# 2014 00007902 B. Does the site contain a brook, body of water or wetlands? NO e DON'T KNOW 0 YES 0 IF YES, has a permit been or need to be obtained from the Conservation Commission? Needs to be obtained 0 Obtained , Date Issued: 12/21/2011 (12PMt N.( NAnOV) C. Do any signs exist on the property? YES 0 NO IF YES, describe size, type and location: D. Are there any proposed changes to or additions of signs intended for the property? YES Ui NO IF YES, describe size, type and location: 2 Signs to mark development entrance(comp. permit)! E. Will the construction activity disturb(clearing, grading, excavation, or filling)over 1 acre or is it part of a common plan that will disturb over 1 acre? YES e NO 0 IF YES,then a Northampton Storm Water Management Permit from the DPW is required. Versionl.7 Commercial Building Permit May 15,2000 SECTION 4-CONSTRUCTION SERVICES FOR PROJECTS LESS THAN 35,000 CUBIC''FEET OF ENCLOSED SPACE Interior Alterations ❑ Existing Wall Signs ❑ Demolition❑ Repairs❑ Additions ❑ Accessory Building❑ Exterior Alteration ❑ Existing Ground Sign❑ New Signs❑ Roofing❑ Change of Use❑ Other❑ Brief Description The proposed scope of work is the construction of a 44 residential unit complex within 4 buildings of wood Of Proposed Work: 'construction. The buildings are 6052 sq.ft.,5863 sq.ft.,7025 sq.ft.,and 7025 sq.ft(greater than 35,00 cubic ft.). SECTION 5-USE GROUP AND CONSTRUCTION TYPE USE GROUP(Check as applicable) CONSTRUCTION TYPE A Assembly ❑ A-1 ❑ A-2 ❑ A-3 ❑ 1A ❑ A-4 ❑ A-5 ❑ 113 ❑ B Business ❑ 2A ❑ E Educational ❑ 2B I ❑ F Factory ❑ F-1 ❑ F-2 ❑ 2C ❑ H High Hazard ❑ 3A ❑ I Institutional ❑ 1-1 ❑ 1-2 ❑ 1-3 ❑ 3B ❑ M Mercantile ❑ 4 ❑ R Residential ❑ R-1 ❑ R-2 R-3 ❑ 5A ❑Q S Storage ❑ S-1 ❑ S-2 ❑ 5B ❑ U Utility ❑ Specify: M Mixed Use ❑ Specify: S Special Use ❑ Specify: COMPLETE THIS SECTION IF EXISTING BUILDING UNDERGOING RENOVATIONS,ADDITIONS AND/OR CHANGE IN USE Existing Use Group: Proposed Use Group: Existing Hazard Index 780 CMR 34): Proposed Hazard Index 780 CMR 34): SECTION 6 BUILDING HEIGHT AND AREA BUILDING AREA EXISTING PROPOSED NEW CONSTRUCTION OFFICE USE ONLY Floor Area per Floor(sf) 1st 1st 12,915 2nd 2"d 13,050 3rd 3rd 4tn 4th Total Area(so Total Proposed New Construction(so 25,965 Total Height(ft) � Total Height ft 3q.5 7.Water Supply(M.G.L.c.40,§54) 7.1 Flood Zone Information: 7.3 Sewage Disposal System: Public [Z] Private ❑ I Zone C Outside Flood Zone❑ Municipal [Z] On site disposal system❑ Version 1.7 Commercial Building Permit May 15,2000 Department use only City of Northampton Sta�us of Permit: Building Department Curb Cut/DdvewayPermit - 4 212 Main Street Sewer/Septic Availability JUN Z��Q Room 100 WaierlWell Availability, N rthampton, MA 01060 Two Sets of Structural Plans G "$ -587-1240 Fax 413-587-1272 PlottSite Plans P�umbrng � 10E Electric, pn,f 0 Northa rP' Other,Specify': APPLICATION TO CONSTRUCT, REPAIR, RENOVATE,CHANGE THE USE OR OCCUPANCY OF,OR DEMOLISH ANY BUILDING OTHER THAN A ONE OR TWO FAMILY DWELLING SECTION 1 -SITE INFORMATION 1.1 Property Address: This section to be completed by office 425 (42 1)North Main Street, Map Lot Unit Leeds, MA 01053 Zone Overlay District. Elm St.District CB District SECTION 2-PROPERTY OWNERSHIP/AUTHORIZED AGENT 2.1 Owner of Record: James Scalise II - Owners Rep., Soldier On, Inc. 421 North Main ST, BLDG 6, Leeds, MA 01053 Name(Print) � Current Mailing Address: (413) 443-3537 Signature Telephone 2.2 Authori e A ent: Name(Print) Current Mailing Address: Signature Telephone SECTION 3-ESTIMATED CONSTRUCTION COSTS Item Estimated Cost(Dollars)to be Official Use Only completed by ermit applicant 1. Building ii) -00 66`$ T q ,oo (a) Building Permit Fee 2. Electrical k �I 6 5/ ,Oa (b)Estimated Total Cost of Construction from 6 3. Plumbing -: LC) ,p a Building Permit Fee r 4. Mechanical(HVAC) 6q D of) •co 050.ee roT/tl,- 5. Fire Protection 914 Dpt) .011 6. Total=0 +2+3+4+5) rj 0 08•eO Check Number This Section For Official Use Only Building Permit Number Date Issued Signature: Building Commissioner/Inspector of Buildings Date File#BP-2014-1295 , APPLICANT/CONTACT PERSON BBL CONSTRUCTION SERVICES LLC ADDRESS/PHONE 302 WASHINGTON AVE EXT ALBANY (518)452-8200 PROPERTY LOCATION 425 NORTH MAIN ST MAP 11 PARCEL 001 001 ZONE THIS SECTION FOR OFFICIAL USE ONLY: PERMIT APPLICATION CHECKLIST ENCLOSED REQUIRED DATE ZONING FORM FILLED OUT Fee Paid Building Permit Filled out Fee Paid Typeof Construction: New Construction Non Structural interior renovations Addition to Existina Accessory Structure Buildine Plans Included: Owner/Statement or License 3 sets of Plans/Plot Plan THE FOLLOWING ACTION HAS BEEN TAKEN ON THIS APPLICATION BASED ON INF�JRMATION PRESENTED: ,,�r Approved Additional permits required(see below) PLANNING BOARD PERMIT REQUIRED UNDER:§ Intermediate Project: Site Plan AND/OR Special Permit With Site Plan Major Project: Site Plan AND/OR Special Permit With Site Plan ZONING BOARD PERMIT REQUIRED UNDER: § Finding Special Permit Variance* Received&Recorded at Registry of Deeds Proof Enclosed Other Permits Required: Curb Cut from DPW Water Availability Sewer Availability Septic Approval Board of Health Well Water Potability Board of Health Permit from Conservation Commission Permit from CB Architecture Committee Permit from Elm Street Commission Permit DPW Storm Water Management Demolition Delay Signature of Building Otticial Date Note: Issuance of a Zoning permit does not relieve a applicant's burden to comply with all zoning requirements and obtain all required permits from Board of Health,Conservation Commission,Department of public works and other applicable permit granting authorities. *Variances are granted only to those applicants who meet the strict standards of MGL 40A.Contact Office of Planning&Development for more information. 425 NORTH MAIN ST BP-2014-1295 GIs#: COMMONWEALTH OF MASSACHUSETTS Map:Block: l l -001 CITY OF NORTHAMPTON Lot:-001 PERSONS CONTRACTING WITH UNREGISTERED CONTRACTORS Permit: Building DO NOT HAVE ACCESS TO THE GUARANTY FUND (MGL c.142A) Category:New Multi-Family Housing BUILDING PERMIT Permit# BP-2014-1295 Project# JS-2013-000735 Est.Cost: $5700000.00 Fee: $9450.00 PERMISSION IS HEREBY GRANTED TO: Const.Class: Contractor: License: Use Group: BBL CONSTRUCTION SERVICES LLC Lot Size(sq. ft.): 451107-3.60 Owner: UNITED STATES VETERANS ADMINISTRATION V.A.HOSPITAL zonin : Applicant: BBL CONSTRUCTION SERVICES LLC AT. 425 NORTH MAIN ST Applicant Address: Phone: Insurance: 302 WASHINGTON AVE EXT (518)452-8200 WC ALBANYNY12203 ISSUED ON.71312014 0:00:00 TO PERFORM TFIE FOLLOWING WORK. CONSTRUCT 4 BLDGS - 44 RES UNITS; INCLUDES FOUND/ TION PERMIT. AFFORDABLE HOUSING AGREEMENT WITHIN 60 DAYS POST THIS CARD SO IT IS VISIBLE FROM THE STREET Inspector of Plumbing Inspector of Wiring D.P.W. Building Inspector Underground: Service: Meter: Footings: Rough: Rough: House# Foundation: Driveway Final: Final: Final: Rough Frame: Gas: Fire Department Fireplace/Chimney: Rough: Oil: Insulation: Final: Smoke: Final: THIS PERMIT MAY PIE REVOKED BY THE CITY OF NORTHAMPTON UPON VIOLATION OF ANY OF ITS RULES AND REGULATIONS. Certificate of Occupancy Signature: FeeType: Date Paid: Amount: Building 7/3/2014 0:00:00 $9450.00 212 Main Street,Phone(413)587-1240,Fax: (413)587-1272 Louis Hasbrouck—Building Commissioner