Loading...
16C-017 (2) EVALUATION REPORT ° ,T Report Number: 0248 Originally Issued: 0912012 Valid Through: 09/2013 TABLE 1: ALLOWABLE LOADS FOR EZ ROOF MOUNT L-FOOT KIT(ibs.)1,2j,4.5 Load Direction Ultimate Load Test Load at Test Load at Calculated Allowable see figure below Test Value 0.250 inch 0.125 inch Fastener/Metal (see ) F.S.=3.0 deflection deflection Strength Design Load Uplift(Withdrawal) 715 1,800 695 340 340 Lateral 260 240 130 153 130 Notes 1. Allowable load values are based on the least value from the ultimate load of three tests(strength limit),tested load at 0.125 inch deflection(deflection limit),calculated fastener capacity(withdrawal or lateral)for wood with a specific gravity of 0.55(Southern Pine)or allowable stress of the aluminum L-foot connector. 2. Allowable load values are based on lumber with all of the following characteristics: a. Located in dry service conditions where the moisture content does not exceed 19%for an extended period of time such as inmost covered structures. b. Located where it does not experience sustained exposure to elevated temperatures that exceed 100°F. For any other conditions,allowable table values shall be multiplied by the related adjustment factor(s)(C,, and/or C)in accordance with the National Design Specificatiotf for Wood Construction(NDS-05). 3. Allowable load.values are based on lumber with a specific gravity of 0.55(Southern Pine or equal). 4. Allowable load values for withdrawal are based on a minimum penetration of 2'/: inches into the roof rafter by one 5116 inch x 4 inch long stainless steel lag screw. 5. Allowable values may not be increased for load duration in accordance with Section 10.3.2 of the NDS-05. EVALUATION REPORT L~ _ (U- Report Number: 0248 Originally Issued: 0912012 Valid Through: 0912013 TABLE 2:MATERIAL PROPERTIES Component Material Shoe Aluminum alloy ANSI/AA A390.0 Waterproof Washer EPDM with durometer ratin of 60 Lag Bolt 304 stainless steel ASTM A 240 L-foot Aluminum alloy 6063-T6 ASTM B221 Hex Cap Aluminum alloy ANSI/AA A380.0 Flashing Aluminum alloy 1060 ASTM B209 EZ ROOF MOUNT COMPONENTS Figure l:Shoe Assembly Figure 4:Hex Cap � .I Figure 2;Lag Bolt Figure S:Flashing i Figure 3:L-foot Page 4 of 4 EVALUATION REPORT Report Number: 0248 Originally Issued: 0912012 Valid Through: 0912013 TABLE 1: ALLOWABLE LOADS FOR EZ ROOF MOUNT L-FOOT HIT(lbs.)1,2,3,4,5 Load Direction Ultimate Load Test Load at Test Load at Calculated Allowable (see figure below) Test Value 0.250 inch 0.125 inch Fastener/Metal Design Load F.S.=3.0 deflection deflection Strength Uplift(Withdrawal) 715 1,800 695 340 340 Lateral 260 240 130 153 130 Notes I. Allowable load values are based on the least value from the ultimate load of three tests(strength limit),tested toad at 0.125 inch deflection(deflection limit),calculated fastener capacity(withdrawal or lateral)for wood with a specific gravity of 0.55(Southern Pine)or allowable stress of the aluminum L-foot connector. 2. Allowable load values are based on lumber with all of the following characteristics: a. Located in dry service conditions where the moisture content does not exceed 19%for an extended period of time such as in most covered structures. b. Located where it does not experience sustained exposure to elevated temperatures that exceed 100°F. For any other conditions,allowable table values shall be multiplied by the related adjustment factor(s)(Cm and/or C,)in accordance with the National Design Specification for Wood Construction(NDS-05). 3. Allowable load values are based on lumber with a specific gravity of 0.55(Southern Pine or equal). 4. Allowable load values for withdrawal are based on a minimum penetration of 2'/2 inches into the roof rafter by one 5116 inch x 4 inch Iong stainless steel lag screw. 5. Allowable values may not be increased for load duration in accordance with Section 10.3.2 of the NDS-05. Uplift Lateral Page 3 of 4 EVALUATION REPORT Report Number: 0248 (U Qriginally Issued: 0912012 Valid Through: 0912013 4.2 Installation Rain test data and thickness of aluminum flashing EZ Roof Mount must be installed using the 5/16 inch for submitte Flashing for Pipe t ae Penetionst(ICC-ES Criteria AC diameter stainless steel lag screw at each bracket 286-2008). Rain test conformed to Underwriters location as described in the manufacturer's installation Laboratory Standard for Gas Vents, UL 441-96 Section instructions. Lag screw must penetrate into the roof 25, rafter a minimum of 2 1/Z inches. Prior to installation,the roof rafter shall be bored with the required lead and Test results are from laboratories in compliance with clearance hole for the unthreaded and shank portions ISO/IEC 17025. of the lag screw as required in Section 11.1.3 of the NDS -05. Threaded portion of the lag screw shall be 7.0 IDENTIFICATION inserted into its lead hole by turning with a wrench and not driving by a hammer. A die-stamp label in the flashing bearing the name and address of the manufacturer, the model number, Use of auxiliary holes in the Shoe other than the use of iAPMO Uniform ES Marks of Conformity, and this an extra fastener to stop the shoe from rotating during Evaluation Report Number(ER-0248). installation is outside the scope of this report. Flashing should be installed full under the shingle up to the raised portion of the flashing to prevent water A p MO U E S ingress under the shingle. No portion of the flashing should be bent upward; the flashing must rest fully ES against the roof shingles. Otherwise the water and wind performance may be impaired. TM 5.0 CONDITIONS OF USE IAPMO#0248 EZ Roof Mount L-Foot Kit for Shingle Roofs described in this report complies with the codes listed in Section 1.0 of this report subject to the following conditions: 5.1 EZ Roof Mount shall be installed in accordance with this report, manufacturer's installation instructions and the codes listed in Section 1.1. 5.2 Calculations to verify the imposed loads on the EZ Roof Mount assembly do not exceed the allowable loads contained in Table 1 of this report shall be submitted to the code official when requested. Calculations shall be prepared by a registered design professional when required by the statues of the jurisdiction where the work is constructed. 6.0 EVIDENCE SUBMITTED Testing and analysis data submitted is in conformance with Evaluation Criteria for Joist Hangers and Miscellaneous Connectors(iAPMO ES EC 002-2011). Page 2 of 4 �U C'k d- EVALUATION REPORT Report Number. 0248 Originally Issued: 0912012 Valid Through: 0912013 Division: 06—WOOD AND PLASTICS 3.0 DESCRIPTION Section: 06060—Connections and Fasteners REPORT HOLDER: 3.1 General Description EZ Roof Mount L-Foot Kit consists of 5 basic SunModotCorporation components: (1) shoe assembly with captive waterproof 1905 SE 5 St,Suite A washer, (2)lag bolt to fasten through the shingles to the Vancouver,WA 98661 roof rafter, (3) flashing that is placed under the row of shingles above the shoe and then over the shoe, (4) L- EVALUATION SUBJECT Foot that is placed over the protruding shoe threads and (5) hex cap that is secured on to the shoe. See SunModo EZ Roof Mount L-Foot Kit for Shingle Figures 1 to 5 in Table 2. Roofs 1.0 EVALUATION SCOPE: 3.2 Materials EZ Roof Mount is fabricated from aluminum. Shoe 1.1 Compliance with the following codes: assembly is fabricated using casting aluminum alloy with dimensions of 2.80 inches in diameter and 1.00 • 2009 International Building Code® inches in height. It is held in place using one 5/16 inch • 2009 international Residential Code® diameter lag bolt that is 4 inch in length and made of • 2006 International Building Code® stainless steel. Flashing is fabricated from sheet 2006 International Residential Code® aluminum with dimensions of 10.0 inches in width, 12.5 inches in length and 0.04 inches in thickness. 1.2 Evaluated In accordance with: L foot is a 2.00 inch long unequal leg angle made from • Evaluation Criteria for Joist Hangers and 6063-T6 aluminum with dimensions of 3.00 inches in Miscellaneous Connectors (IAPMC ES EC002- depth, 2.00 inches in width and 0.24 inches in 2011),Approved March 2011 thickness. It contains a 0.375 inch diameter round hole • Acceptance Criteria for Roof Flashing for Pipe with a 0.83 inch diameter chamfer (in base) that is Penetrations(iCC-ES AC286),Approved April 2010 located in the center of the base leg. One slot measuring 1.64 inch long by 0.40 inch wide occurs in 1.3 Properties Evaluated: the center and is located 0.30 inches from the top edge of the vertical leg, which has a scallop front and rear • Structural face. See Table 2 for component material properties • Weather Protection and figures. 2.0 USES 4.0 DESIGN AND INSTALLATION EZ Roof Mount L-Foot Kit'for Shingle Roofs is used to 4.1 Design mount solar systems and other rooftop devices such as satellite dishes on asphalt shingle roofs with wood Tabulated allowable loads shown in Table 1 of this rafters underneath. report are based on allowable stress design (ASD). Adjustments to these values are required for wet EZ Roof Mount is specifically designed to be used for service conditions, sustained exposure to elevated installation of solar panels for electric or hot water temperatures, use with fire retardant lumber or with production on roofs with slopes from 3 to 12 units lumber whose specific gravity is less than 0.55 vertical in 12 units horizontal. (Southern Pine). Allowable values based on fastener strength may be adjusted for duration of loading. See footnotes of Table 1 for more detailed explanation. Page 1 of 4 Copyright m 2012 by International Association of Plumbing and Mechanical officials.At rights reserved.Printed In the United States.No part of this publication may be reproduced,stared in an electronic retrieval system,or transmitted,M any forth or by any means,sledMia,mechanical,photocopying,recording,or otherwise,vrilhoul the prior mitten permission of the pvbllsher.Ph:7-877-4fESRP7•Fax:909.472.4171•Web:www.laomaesom•$001 East Philadelphia Street•Ontario,California 91761-2616—USA �� Qj Mechanical Properties 0 Electrical Properties(STC2) Cells 6 x 10 300 W 295 W 290W 285W 280 W Cell vendor _.... LG Maximum power Pmex.(W) 'GJ _ 295 2`'0 `f', 7,80 Cell type MonocryQalline Cell dimensions- rrl - 156 x 1�6 m MPP voltageVmpp(V) 320 3 31.6 31.6 315 Cell busbar 3 MPP current lmpp(A) 34;' 9.3n. 9.19 9.0" 8.9 Front cover Glass Open circuIt vol tage Voc(V) 39.5 393 39.2 33.0 38'3 Dimensions(L x W x H) 1640 x 1000 x 35(mm) Short circuit current Isc(A) 100 '391 9:50 9.66 9.Fi6 Static load 5400 i,e(snow) Module efficiency( ) V1 3 1;>.0 r 1 171 2400... a(wind)..... Operating temperature(^C). _ _410..+901 Weight 16 8-+0,5 kg_ Maximum system voltage(V).. 1000 Connector type V(74 connector IF'67 - Maximum series fuse rating(A) lf> Junction box IP 67 with 3 bypass diodes - - Length of cables 2 x 1000 min Power toleIrance(%) 0-.+5 Frame Anoduod Aklminum ,rr( ,,r I,d�esr _, ,:.,,p.o-„1„ .1rn , ... nd„I •+pn ic, ,, ,_ -c�,. ,,.tol - ,-.I it-r.ass ll then. xpl#.I.,er Lai".n..- „ la--:dc.......... F✓I., FI. rmi..rt nlz_n nd,1 n1,1"il-......... Certifications and Warranty Certifications IFC 61215,IFC 61730-1/-,-, 10 Electrical Properties(NOCV) ISO 14001,ISO 9001, OHSAS 16001, 300 W 295 W 290 W 285 W 280 W IJL 1703 Maximum power(Pmpp) 220 216 213 110 206 Product warranty _..... 10 years _..._ _ MPP voltage(Vmpp) _ c19 ,2.. l:a "r':£,a 28 Output warranty of Pmax. (PAuasurement Iclerancw+_3"i„i �years inear wa!ranty MPP current(Ill E,12 ...... . .>25 - :1 u "r -I y a n,�=1 ,h E Open circuit voltage(Voc).. . r 5..... .:3 6_3 362 ... _',6 0 35.9 Short circuit current(Isc) 6.016 7-,3 7.89 7.80 770 o- loco Temperature Coefficients Efficiency reduction re m't.200 W/m') NOCT 45±? Call l.,r l,r rtPC Ir.1 , ,:SL, Pmpp 042%/K Voc -0.31 /K 10 10 Isc _ 003%/It ....... ...... . ... ....... C C,.. ...... r Zr. 0 Dimensions (mm) I Characteristic Curves — a 10 loco w .. 360 �+ 9 -- D 1 c..t l 40175(Y ) V 1 BLOW tr D.�inF �� 1H ( 1 1 b— 5 ........._........ 60 0 w-- 04.3 A A� 6 � � 12 C ound�nq holey l p q 400 W s CJ8 O(Z v ) --- - =J (_ 200 w a ') _y d ' o S 10 IS 20 25 +0 35 40 lv l,Il a(V) H' Hi t-o i 120 IsC a in oels:rr Pmax 40 4 3 r' 0 I -40 -25 0 25 50 75 go Temperature(°C) f I,_ ioUnf,,1/1 una nq y L CI I i D I 31-nd GrnbH� a All I f I II h --,ply',ieh DI'1 F I Cc e 1aR 13 11 1 1 hn :' •'* -. Life's Good ws„I.,r �n. 31,I �u1;�s EI r I r nl« II n,ll:IS. �„r„1 RM. � A a _ ! ' N 2 Cx _.-_._... ....._... _ _.._ lil ..� - -- . .... -_ i V a wc' w I coo j � v w ; I wo w E i C O U O fD j LAJ U c N [l w G Q- o a UQ CL s d ❑ cu o i U ❑ice > U O�iD I ° v 0 W 4 r L W j o r F-b n w Q 0 K ' w o a 0 0 16 i LL rL 3 hN U. 3 i S hr� I LL i c c I � a 5 7 c° c � .O i I sa,avn I i CD 0 CD CD Cn CAD T V � ■ CD Arm �kyWW. N �u CD Amok, O (/D1 ML sk 0. Is C CD n e-t, W CDr-f Q Vreeland Design Associates An integrative approach to design engineering and site planning Date: February 12, 2014 To: Ann Bronner NorthEast Solar 136 Elm Street Hatfield, MA 01038 From: David Vreeland, P.E. Vreeland Design Associates Re: Peter King and Lissie Fein, 226 Spring St, Florence, MA: Structural assessment of existing detached garage roof to support proposed solar array. I have reviewed the existing garage roof framing in the area of the proposed PV panel installation. The existing rafters are full dimension 2x6 installed at 24" on-center, and appear to be hemlock spanning 11'-6" at approximately a 7.5/12 pitch. The roofing is metal panel installed on top of a single layer of asphalt shingles. 1x6 collar ties are installed 4' on-center. The roof framing needs to be reinforced my installing 2x6 collar ties or 1/8" high-strength steel cable on the rafters that do not have collar ties. The new collar ties or cable can be installed a maximum of 12"above the top plate. The existing collar ties can be replaced with new ties/cable also installed at the same height as the new collar ties. Attach the 2x6 collar ties to the rafters with 4-31/2" Ledgerlok screws as well as at the overlap of the two-piece collar tie. To minimize deflection of the new collar-ties, install a vertical 2x4 near mid-span to connect the collar-tie to the rafter above. Contact me to discuss attachment options if you choose to use the cable. I have reviewed the mounting details for the proposed array. Based on the specified PV panel unit weight of 37 Ibs, with the attachment points of the array placed at a maximum of 4' on center and staggered to minimize the load to any one rafter, the existing roof framing is adequate to support the proposed PV array. Please contact me if you have any questions or need additional information. Sincerely, ,,IN of 44 s DAVID A. G VREELAND David Vreeland, PE CIVIL No.46317 Vreeland Design Associates -'0 Glis e4�� `csS/ONAI 116 River Road, Leyden, MA 01337 Phone: (413) 624-0126 Email: dvreeland @verizon.net Fax: (413) 624-3282 The Commonwealth of Massachusetts Department of Industrial Accidents # Office of Investigations ' 600 Washington Street Boston, MA 02111 �A , F www.mass.gov/dia Workers' Compensation Insurance Affidavit: Builders/Contractors/Electricians/Plumbers Applicant Information Please Print Legibly Name (Business/Organization/Individual): NorthEast Solar Design Address: 136 Elm St . City/State/Zip: Hatfield, Ma . 01038 Phone #: 413-247-6045 Are you an employer?Check the appropriate box: Type of project(required): LE I am a employer with 9 4. ❑ I am a general contractor and I employees(full and/or part-time).* have hired the sub-contractors 6. ❑ New construction 2.❑ I am a sole proprietor or partner- listed on the attached sheet. 7. ❑ Remodeling ship and have no employees These sub-contractors have g, ❑ Demolition working or me in an capacity. employees and have workers' g y 9. E] Building addition [No workers' comp. insurance comp. insurance.1 required.] 5. ❑ We are a corporation and its 10.0 Electrical repairs or additions 3.❑ 1 am a homeowner doing all work officers have exercised their 11.❑ Plumbing repairs or additions myself. [No workers' comp. right of exemption per MGL 12.0 Roof repairs insurance required.] t c. 152, §1(4), and we have no 13. ] Other Solar employees. [No workers' comp. insurance required.] *Any applicant that checks box#1 must also till out the section below showing their workers'compensation policy information. t Homeowners who submit this affidavit indicating they are doing all work and then hire outside contractors must submit a new affidavit indicating such. tContractors that check this box must attached an additional sheet showing the name of the sub-contractors and state whether or not those entities have employees. If the sub-contractors have employees,they must provide their workers'comp.policy number. I am an employer that is providing workers'compensation insurance for my employees. Below is the policy and jab site information. Insurance Company Name: Hanover Insurance Policy #or Self-ins. Lic.#: WHN 5715134-02 Expiration Date: 4/8/15 Job Site Address: 226 Spring St . City/State/Zip: Florence, Ma 01062 Attach a copy of the workers' compensation policy declaration page(showing the policy number and expiration date). Failure to secure coverage as required under Section 25A of MGL c. 152 can lead to the imposition of criminal penalties of a fine up to $1,500.00 and/or one-year imprisonment, as well as civil penalties in the form of a STOP WORK ORDER and a fine Of tip to $250.00 a day against the violator. Be advised that a copy of this statement may be forwarded to the Office of Investigations of the DIA for insurance coverage verification. I do hereby certify and ze pai n enalties of perjury that the information provided above is true and correct. Si nature• Date: 1/20/14 Phone#: 413-247-6045 Official use only. Do not write in this area, to be completed by city or town official. City or Town: Permit/License# Issuing Authority (circle one): 1. Board of Health 2. Building Department 3. City/Town Clerk 4. Electrical Inspector 5. Plumbing Inspector 6. Other Contact Person: Phone#: SECTION 8-CONSTRUCTION SERVICES 7 8.1 Licensed Construction Supervisor: Not Applicable ❑ Name of License Holder: Phillip Baunsgard CS106113 License Number 11 Edward Ave . Southam ton, Ma 01073 6/7/15 res Expiration Date 413-247-6045 ture Telephone 9. Registered Home Improvement Contractor: Not Applicable ❑ Northeast Solar 169641 Company Name Registration Number 136 Elm St . Hatfield, Ma 01038 7/14/15 Address Expiration Date a Telephone 413-247-6045 SECTION 10-WORKERS'COMPENSATION INSURANCE AFFIDAVIT(M.G.L.c. 152,§25C(6)) Workers Compensation Insurance affidavit must be completed and submitted with this application. Failure to provide this affidavit will result in the denial of the issuance of the building permit. Signed Affidavit Attached Yes.......& No...... ❑ ll. - Home Owner Exemption The current exemption for"homeowners"was extended to include Owner-occupied Dwellings of one(1) or two(2)families and to allow such homeowner to engage an individual for hire who does not possess a license,provided that the owner acts as supervisor.CMR 780, Sixth Edition Section 108.3.5.1. Definition of Homeowner: Person(s)who own a parcel of land on which he/she resides or intends to reside,on which there is,or is intended to be,a one or two family dwelling,attached or detached structures accessory to such use and/or farm structures.A person who constructs more than one home in a two-year period shall not be considered a homeowner. Such"homeowner"shall submit to the Building Official,on a form acceptable to the Building Official,that he/she shall be responsible for all such work performed under the building permit. As acting Construction Supervisor your presence on the job site will be required from time to time,during and upon completion of the work for which this permit is issued. Also be advised that with reference to Chapter 152(Workers' Compensation) and Chapter 153 (Liability of Employers to Employees for injuries not resulting in Death)of the Massachusetts General Laws Annotated,you may be liable for person(s) you hire to perform work for you under this permit. The undersigned"homeowner"certifies and assumes responsibility for compliance with the State Building Code,City of Northampton Ordinances, State and Local Zoning Laws and State of Massachusetts General Laws Annotated. Homeowner Signature Section 4. ZONING All Information Must Be Completed. Permit Can Be Denied Due To Incomplete Information Existing Proposed Required by Zoning This column to be filled in by Building Department Lot Size Frontage Setbacks Front Side L: R: L: R: Rear Building Height Bldg. Square Footage % Open Space Footage % (Lot area minus bldg&paved parking) #of Parking Spaces Fill: volume&Location A. Has a Special Permit/Variance/Finding ever been issued for/on the site? NO 0 DON'T KNOW YES 0 IF YES, date issued:' IF YES: Was the permit recorded at the Registry of Deeds? NO 0 DON'T KNOW YES 0 IF YES: enter Book Page and/or Document# B. Does the site contain a brook, body of water or wetlands? NO DON'T KNOW 0 YES 0 IF YES, has a permit been or need to be obtained from the Conservation Commission? Needs to be obtained 0 Obtained 0 , Date Issued: C. Do any signs exist on the property? YES 0 NO IF YES, describe size, type and location: D. Are there any proposed changes to or additions of signs intended for the property? YES 0 NO 0 IF YES, describe size, type and location: E. Will the construction activity disturb(clearing, grading,excavation, or filling)over 1 acre or is it part of a common plan that will disturb over 1 acre? YES Q NO IF YES,then a Northampton Storm Water Management Permit from the DPW is required. SECTION 5-DESCRIPTION OF PROPOSED WORK(check all applicable) New House ❑ Addition ❑ Replacement Windows Alteration(s) ❑ Roofing ❑ Or Doors E] Accessory Bldg. ❑ Demolition ❑ New Signs [O] Decks [Q Siding[tom] Other[©] Brief Description of Proposed Work: Install 18 solar panels on the garage roof. Alteration of existing bedroom Yes No Adding new bedroom Yes No Attached Narrative Renovating unfinished basement Yes _No Plans Attached Roll -Sheet 6a. If New house and or addition to existing housing, complete the following: a. Use of building : One Family Two Family Other b. Number of rooms in each family unit: Number of Bathrooms c. Is there a garage attached? d. Proposed Square footage of new construction. Dimensions e. Number of stories? f. Method of heating? Fireplaces or Woodstoves Number of each g. Energy Conservation Compliance. Masscheck Energy Compliance form attached? h. Type of construction i. Is construction within 100 ft. of wetlands? Yes No. Is construction within 100 yr. floodplain Yes No j. Depth of basement or cellar floor below finished grade k. Will building conform to the Building and Zoning regulations? Yes No . I. Septic Tank City Sewer Private well City water Supply SECTION 7a-OWNER AUTHORIZATION-TO BE COMPLETED WHEN OWNERS AGENT OR CONTRACTOR APPLIES FOR BUILDING PERMIT I, 4-.,—v, 1 as Owner of the subject property hereby authorize Northeast Solar to act on m half, in all matters relative to work authorized by this building permit application. 1/20/14 Sign, re of Owner Date as Owner/Authorized Agent her eft declare that the statementsAnd information on the foregoing application are true and accurate,to the best of my knowledge and belief. Signed under the pai an penalties of perjury. _4 A7 Y7 Print Nam U� — l Signature of Owner/Agen Date r.`f=`tvti;•t#r.#€r(r#!;n I(Ex,,r�.=}i i'�rrnrC t I,-one 4 15U74240 ,x 11<. r 127 >iM twPl_ AF=€rr,r..r:IL3rN 10 UUNY RIXT,+'tt.n17.A"AIR.f MOVA M M D MY Mq A ONE OR TWO€AMILY DY .€,ENG i Sf CC TO NI S 0 E INFQ1R t2A T!{}t,4 IMP LM E �� 'tC1't�.r• ,p�.°.,rTF ,tVYNERS+ttF^Al)TNGs1atI�C,4Cx�Pdt t e y .,�✓� i t J � S'ttf t! ti' it J%17,t,t S�T�7t.y_�� �?`A.A.'eerGgN57�UC7s�td�VS..iS r i twm nmd raw coq or _ ... _...___ ' �r n c,•;Frcri 5.51 .__..._.. I f3mkfing f^ormlt Fey* .�. 7h R Sm'Hon For Ca!jMl Use Jnix_ 740 J Eat!t�7� `r?rr d tf rt�Ea,Ft _ r I (P.ACr"q E r,rc-Rns�2i rw rtxP+'t r rrt f4,rf�W-a r.r�r ' a !Iw, I Department use only I y � City of Northampton Status of Permit: ' �j i Building Department Curb Cut/Driveway Permit FEB 1 9 2014 J 212 Main Street Sewer/Septic Availability Room 100 WaterNVell Availability L (-: 's 15,�PectioR rthampton, MA 01060 Two Sets of Structural`Plans 6 '�'' �'� ��1�6� 3-587-1240 Fax 413-587-1272 Plot/Site Plans Other Specify APPLICATION TO CONSTRUCT,ALTER, REPAIR, RENOVATE OR DEMOLISH A ONE OR TWO FAMILY DWELLING SECTION 1 -SITE INFORMATION 1.1 Property Address: This section to be completed by office Map Lot Unit 226 Spring St . Florence Zone Overlay District Elm St.District CB District SECTION 2-PROPERTY OWNERSHIP/AUTHORIZED AGENT 2.1 Owner of Record: Peter King and Lizzie Fein 226 Spring St. Florence,Ma 01062 Name(Print) Current Mailing Address: jn� 413-517-3986 / '� Telephone Signature 2.2 Authorized Accent: Northeast Solar 136 m t. Hatfield,Ma 01038 413247-6045 Northeast Solar 136 Elm St.Hatfield,Ma 01038 413247-6045 Na rint) Current Mailing Address: Northeast Solar 136 Elm St.Hatfield, Ma 01038 413247-6045 Signature Telephone SECTION 3-ESTIMATED CONSTRUCTION COSTS Item Estimated Cost(Dollars)to be Official Use Only completed by ermit applicant 1. Building 21,318 (a) Building Permit Fee 2. Electrical (b) Estimated Total Cost of Construction from 6 3. Plumbing Building Permit Fee 4. Mechanical(HVAC) 5. Fire Protection 6. Total=(1 +2+ 3+4+ 5) 21,318 1 Check Number This Section For Official Use Only Building Permit Number: Date Issued: Signature: Building Commissioner/Inspector of Buildings Date File#BP-2014-0889 APPLICANT/CONTACT PERSON NORTHEAST SOLAR DESIGN ASSOCIATES LLC ADDRESS/PHONE 136 ELM ST HATFIELD (413)247-6045 Q PROPERTY LOCATION 226 SPRING ST MAP 16C PARCEL 017 001 ZONE URA(100)/WSP(100)/ THIS SECTION FOR OFFICIAL USE ONLY: PERMIT APPLICATION CHECKLIST ENCLOSED REQUIRED DATE ZONING FORM FILLED OUT Fee Paid Building Permit Filled out Fee Paid Tpeof Construction: INSTALL 18 GARAGE ROOF SOLAR PANELS New Construction Non Structural interior renovations Addition to Existing Accessory Structure Building Plans Included• Owner/Statement or License 106113 3 sets of Plans/Plot Plan THE FOLLOWING ACTION HAS BEEN TAKEN ON THIS APPLICATION BASED ON INF0,4MATION PRESENTED: pproved Additional permits required(see below) PLANNING BOARD PERMIT REQUIRED UNDER:§ Intermediate Project: Site Plan AND/OR Special Permit With Site Plan Major Project: Site Plan AND/OR Special Permit With Site Plan ZONING BOARD PERMIT REQUIRED UNDER: § Finding Special Permit Variance* Received&Recorded at Registry of Deeds Proof Enclosed Other Permits Required: Curb Cut from DPW Water Availability Sewer Availability Septic Approval Board of Health Well Water Potability Board of Health Permit from Conservation Commission Permit from CB Architecture Committee Permit from Elm Street Commission Permit DPW Storm Water Management e o ' ' n Del 4;ture of Buil ing fficial Date Note: Issuance of a Zoning permit does not relieve a applicant's burden to comply with all zoning requirements and obtain all required permits from Board of Health,Conservation Commission,Department of public works and other applicable permit granting authorities. *Variances are granted only to those applicants who meet the strict standards of MGL 40A.Contact Office of Planning&Development for more information. 226 SPRING ST BP-2014-0889 GIs#: COMMONWEALTH OF MASSACHUSETTS Map:Block: 16C-017 CITY OF NORTHAMPTON Lot: -001 PERSONS CONTRACTING WITH UNREGISTERED CONTRACTORS Permit: Building DO NOT HAVE ACCESS TO THE GUARANTY FUND (MGL c.142A) Category: SOLAR PANELS BUILDING PERMIT Permit# BP-2014-0889 Project# JS-2014-001542 Est. Cost: $21318.00 Fee: $126.00 PERMISSION IS HEREBY GRANTED TO: Const. Class: Contractor: License: Use Group: NORTHEAST SOLAR DESIGN ASSOCIATES LLC 106113 Lot Size(sq. ft.): 80324.64 Owner: KING PETER Zoning: Applicant: NORTHEAST SOLAR DESIGN ASSOCIATES LLC AT. 226 SPRING ST Applicant Address: Phone: Insurance: 136 ELM ST (413)247-6045 () Workers Compensation HATFIELDMA01038 ISSUED ON:212012014 0:00:00 TO PERFORM THE FOLLOWING WORK.-INSTALL 18 GARAGE ROOF SOLAR PANELS POST THIS CARD SO IT IS VISIBLE FROM THE STREET Inspector of Plumbing Inspector of Wiring D.P.W. Building Inspector Underground: Service: Meter: Footings: Rough: Rough: House# Foundation: Driveway Final: Final: Final: Rough Frame: Gas: Fire Department Fireplace/Chimney: Rough: Oil: Insulation: Final: Smoke: Final: THIS PERMIT MAY BE REVOKED BY THE CITY OF NORTHAMPTON UPON VIOLATION OF ANY OF ITS RULES AND REGULATIONS. Certificate of Occupancy Signature: FeeType: Date Paid: Amount: Building 2/20/2014 0:00:00 $126.00 212 Main Street,Phone(413)587-1240,Fax: (413)587-1272 Louis Hasbrouck—Building Commissioner