Loading...
06-064 Fire Retardant Paint Latex Flat Finish LFR-110 Surface Preparation Application Surfaces to be painted must be clean, dry and free of oil, grease, Stir this product thoroughly before use. Once stirred, Insl-x Fire dust, rust, mill scale, loose paint, chalk and other contaminants that Retardant Paint is ready to use. Do not incorporate any additives could interfere with adhesion. Glossy surfaces should be dulled by into this product and thin with water only as needed.Do not apply if abrading the surface. surface or air temperatures are below 50°F or above 95°F. Previously Painted Surfaces: No primer is needed if surface is in Brush:Synthetic Bristle only. good condition.Clean and sand as needed. Roller:3/8"to 1/2"Nap Synthetic Roller Ferrous Metal: Remove loose rust and mill scale with a grinder, scraper, wire brush or sandpaper. Remove oil and grease as Airless Spray: Fluid Pressure — 1500 to 2500 psi. necessary using an oil and grease emulsifying cleaner. Prime bare Tip Size-.013 to.017 spots with metal primer. Wood/Drywall: Spot prime patched and spackled areas with the Cleanup recommended primer before topcoating. Clean all equipment immediately after use with soap and water. WARNING! If you scrape, sand or remove old paint, you may Spray equipment should be given a final rinse with mineral spirits release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST to prevent corrosion. CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, USE COMPLETELY OR DISPOSE OF PROPERLY. Local ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD disposal requirements vary; consult your sanitation ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to department or state-designated environmental agency on control lead exposure. Carefully clean up with a HEPA vacuum and disposal options. a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at Environmental, Health &Safety Information 1-800-424-LEAD or log on to www.eoa.gov/lead. Use only with adequate ventilation. Do not breathe spray mist or sanding dust. Ensure fresh air entry during application and drying.Avoid contact with eyes and prolonged or repeated contact with skin. Avoid exposure to dust and spray mist by wearing a NIOSH approved respirator during application, sanding and clean up. Follow respirator manufacturer's directions for respirator use. Close container after each use.Wash thoroughly after handling. WARNING: This product contains a chemical known to the state of Califomia to cause cancer and birth defects, or other reproductive harm. FIRST AID: In case of eye contact,flush immediately with plenty of water for at least 15 minutes; for skin, wash thoroughly with soap and water. If symptoms persist, seek medical attention. If you experience difficulty breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately. IN CASE OF SPILL—Absorb with inert material and dispose of as specified under"Cleanup". KEEP OUT OF REACH OF CHILDREN PROTECT FROM FREEZING Refer to Material Safety Data Sheet for additional health and safety information. ` Complementary Coatings Corp. Florida's, NJ A BM&Co.offiliole Complementary Coatings Corp.,360 Rt.206,Flanders,NJ 07836 Tel:800-225-5554 Fax:888-248-2143 www.lnsl-x.com M72 LFR-110 US 021513 INSL-X is a registered trademark of Complementary Coatings Corp.©2013 Complementary Coatings Corp. All rights reserved All other trademarks belong to their respective owners r— e to�e ,�, - 06 - �� -�J C�ea s�ogc X FIRE RETARDANT PAINT MP LATEX INTUMESCENT COATING FLAT FINISH LFR-110 Features General Description • Intumescent product • Applies like a regular Insl-x®Fire Retardant Paint is a high-quality latex decorative, • Flame Spread Rating: paint intumescent,fire retardant coating for interior ceilings,walls Class"A"when tested in • Soap and water cleanup and trim.This product provides a high-hiding matte finish that accordance with ASTM retards flame spread by reacting to heat and forming a thick E-84(NFPA 255)and S- cellular char blanket(intumescence).By reducing excessive 102. heat penetration,this product retards flame spread and minimizes smoke generation.It is suitable for primed or previously painted wood,drywall,cellulose tile,cured plaster, masonry and metal.It applies like a conventional latex paint,is low in odor,low in V005,and washes without spottin.. Recommended For Limitations For interior use on primed or previously painted wood,drywall, • Use product when surface temperature is between 50°F cellulose tile,cured plaster,masonry and metal.NOTE:Top (10°C)and 95°F(35°C). coating this product will reduce its intumescent properties. Product Information Colors—Standard: Technical Data White White Vehicle Type Vinyl Acrylic Pigment Type Titanium Dioxide Volume Solids 48.0±1.0% —Tint Bases: Coverage per Gallon at 300 Sq.Ft. Can be tinted with Universal Colorants. Recommended Film Thickness Recommended Film –Wet 5.3 mils Thickness –Dry 2.5 mils Depending on surface texture and porosity. Be sure to Special Colors: estimate the right amount of paint for the job. This will P ensure color uniformity and minimize the disposal of Contact your dealer. excess paint. Dry Time @ 77°F –Tack Free 30 Minutes Certification: (25°C)@ 50%RH –To Recoat 4 Hours High humidity and cool temperatures will result in longer The products supported by this data sheet contain a maximum of 50 grams dry,recoat and service times. per liter VOCNOS(0.42 lbs/gal.)excluding water&exempt solvents. This product is compliant under the Ozone Transport Commission Dries By Evaporation regulations as a Flat Coating. Viscosity 70–80 KU This product meets qualifications for LEED(Leadership in Energy and Flash Point N/A Environmental Design)projects as a Flat Coating. Gloss/Sheen Flat Surface Temperature –Min. 50°F at Application –Max. 95°F Thin With Not Necessary Clean Up Thinner Warm Soapy Water Weight Per Gallon 10.8 lbs. Technical Assistance: –Min. 50°F Storage Temperature Available through your local authorized independent Insl-x dealer.For the –Max. 90°F location of the dealer nearest you,call 1-800-225-5554,see www.insl-x.com Volatile Organic Compounds(VOC) or consult your local Yellow Pages. 45 Grams/Liter 0.37 Lbs./Gallon 0 Reported values are for White,Contact dealer for values of other bases or colors. Complementary Coatings Corp.,360 Rt.206,Flanders,NJ 07836 Tel:800-225-5554 Fax:888-248-2143 www.lnsl-x.com M72 LFR-110 US 030713