The URL can be used to link to this page

967 Florence Rd Solar 2024 City of Northampton Building Department 212 Main Street Room 100 Northampton, MA 01060 phone 413-587-1240 Fax 413-587-1272 Department use only Status of Permit: Curb Cut/Driveway Permit ____________________ Sewer/Septic Availability______________________ Water/Well Availability________________________ Two Sets of Structural Plans___________________ Plot/Site Plans_____________ Other Specify__________ APPLICATION TO CONSTRUCT, ALTER, REPAIR, RENOVATE OR DEMOLISH A ONE OR TWO FAMILY DWELLING SECTION 1 - SITE INFORMATION 1.1 Property Address: This section to be completed by office Map _______________ Lot __________________Unit_________ Zone ________________ Overlay District______________ Elm St. District__________________ CB District______________ SECTION 2 - PROPERTY OWNERSHIP/AUTHORIZED AGENT 2.1 Owner of Record: ______________________________________________________ Name (Print) _____________________________________________________ Signature _____________________________________________________ Current Mailing Address: ______________________________________________________ Telephone 2.2 Authorized Agent: ______________________________________________________ Name (Print) ______________________________________________________ Signature ______________________________________________________ Current Mailing Address: ______________________________________________________ Telephone SECTION 3 - ESTIMATED CONSTRUCTION COSTS Item Estimated Cost (Dollars) to be completed by permit applicant Official Use Only 1. Building (a) Building Permit Fee 2. Electrical (b) Estimated Total Cost of Construction from (6) 3. Plumbing Building Permit Fee 4. Mechanical (HVAC) 5. Fire Protection 6. Total = (1 + 2 + 3 + 4 + 5) Check Number This Section For Official Use Only Building Permit Number:_______________________________ Date Issued:______________________________________________ Signature: ______________________________________________ Building Commissioner/Inspector of Buildings _______________________________ Date Section 4. ZONING All Information Must Be Completed. Permit Can Be Denied Due To Incomplete Information Existing Proposed Required by Zoning This column to be filled in by Building Department Lot Size Frontage Setbacks Front Side Rear L:______ R:______ L:______ R:______ Building Height Bldg. Square Footage % Open Space Footage (Lot area minus bldg & paved parking) % # of Parking Spaces Fill: (volume & Location) A. Has a Special Permit/Variance/Finding ever been issued for/on the site? NO DON'T KNOW YES IF YES, date issued: IF YES: Was the permit recorded at the Registry of Deeds? NO DON'T KNOW YES IF YES: enter Book Page and/or Document # B. Does the site contain a brook, body of water or wetlands? NO DON'T KNOW YES IF YES, has a permit been or need to be obtained from the Conservation Commission? Needs to be obtained Obtained , Date Issued: C. Do any signs exist on the property? YES NO IF YES, describe size, type and location: D. Are there any proposed changes to or additions of signs intended for the property ? YES NO IF YES, describe size, type and location: E. Will the construction activity disturb (clearing, grading, excavation, or filling) over 1 acre or is it part of a common plan that will disturb over 1 acre? YES NO IF YES, then a Northampton Storm Water Management Permit from the DPW is required. SECTION 5- DESCRIPTION OF PROPOSED WORK (check all applicable) New House Addition Replacement Windows 0r Doors Alteration(s) Roofing Accessory Bldg. Demolition New Signs [ ] Decks [ ] Siding [ ] Other [ ] _________________________________________________________________ Brief Description of Proposed Work:________________________________________________________________________________________ Alteration of existing bedroom ______Yes ______ No Adding new bedroom _______ Yes _______ No Attached Narrative Renovating unfinished basement _______ Yes _______No Plans Attached Roll - Sheet 6a. If New house and or addition to existing housing, complete the following: a. Use of building : One Family _________ Two Family _________ Other __________ b. Number of rooms in each family unit:______________ Number of Bathrooms_____________ c. Is there a garage attached? _________ d. Proposed Square footage of new construction._____________________ Dimensions __________________________________ e. Number of stories? ________________________________ f. Method of heating? ________________________________ Fireplaces or Woodstoves ___________ Number of each ______ g. Energy Conservation Compliance. _____________________ Masscheck Energy Compliance form attached? _______________ h. Type of construction _______________ i. Is construction within 100 ft. of wetlands? ______ Yes ______ No. Is construction within 100 yr. floodplain ______Yes _____No j. Depth of basement or cellar floor below finished grade __________________________ k. Will building conform to the Building and Zoning regulations? ________ Yes _______ No . l. Septic Tank _____ City Sewer _______ Private well _______ City water Supply _______ SECTION 7a - OWNER AUTHORIZATION - TO BE COMPLETED WHEN OWNERS AGENT OR CONTRACTOR APPLIES FOR BUILDING PERMIT I, _______________________________________________________________________________________, as Owner of the subject property hereby authorize ________________________________________________________________________________________________ to act on my behalf, in all matters relative to work authorized by this building permit application. ______________________________________________________________________________________________________________ Signature of Owner Date I, _______________________________________________________________________________________, as Owner/Authorized Agent hereby declare that the statements and information on the foregoing application are true and accurate, to the best of my knowledge and belief. Signed under the pains and penalties of perjury. ______________________________________________________________________________________________________________ Print Name ______________________________________________________________________________________________________________ Signature of Owner/Agent Date SECTION 8 - CONSTRUCTION SERVICES 8.1 Licensed Construction Supervisor: Name of License Holder :___________________________________________________________ ___________________________________________________________________________ Address ___________________________________________________________________________ Signature Telephone Not Applicable ! _____________________________________ License Number _____________________________________ Expiration Date 9. Registered Home Improvement Contractor: __________________________________________________________________________ Company Name __________________________________________________________________________ Address _________________________________________________Telephone_________________ _ Not Applicable ! _________________________________ Registration Number _________________________________ Expiration Date SECTION 10- WORKERS’ COMPENSATION INSURANCE AFFIDAVIT (M.G.L. c. 152, § 25C(6)) Workers Compensation Insurance affidavit must be completed and submitted with this application. Failure to provide this affidavit will result in the denial of the issuance of the building permit. Signed Affidavit Attached Yes....... ! No...... ! 11. - Home Owner Exemption The current exemption for “homeowners” was extended to include Owner-occupied Dwellings of one (1) or two(2) families and to allow such homeowner to engage an individual for hire who does not possess a license, provided that the owner acts as supervisor. CMR 780, Sixth Edition Section 108.3.5.1. Definition of Homeowner: Person (s) who own a parcel of land on which he/she resides or intends to reside, on which there is, or is intended to be, a one or two family dwelling, attached or detached structures accessory to such use and/ or farm structures. A person who constructs more than one home in a two-year period shall not be considered a homeowner. Such “homeowner” shall submit to the Building Official, on a form acceptable to the Building Official, that he/she shall be responsible for all such work performed under the building permit. As acting Construction Supervisor your presence on the job site will be required from time to time, during and upon completion of the work for which this permit is issued. Also be advised that with reference to Chapter 152 (Workers’ Compensation) and Chapter 153 (Liability of Employers to Employees for injuries not resulting in Death) of the Massachusetts General Laws Annotated, you may be liable for person(s) you hire to perform work for you under this permit. The undersigned “homeowner” certifies and assumes responsibility for compliance with the State Building Code, City of Northampton Ordinances, State and Local Zoning Laws and State of Massachusetts General Laws Annotated. Homeowner Signature ________________________________________________________ City of Northampton 212 Main Street, Northampton, MA 01060 Solid Waste Disposal Affidavit In accordance of the provisions of MGL c 40, S54, I acknowledge that as a condition of t he building permit all debris resulting from the construction acti vity governed by this Building Permit shall be disposed of in a properly licensed solid waste disposal facility, as defined by MGL c 111, S 150A. Address of the work: _______________________________ The debris will be transported by: ______________________________ The debris will be received by: ______________________________ Building permit number: ______________________________ Name of Permit Applicant ______________________________ __________________________________________ Date Signature of Permit Applicant The Commonwealth of Massachusetts Department of Industrial Accidents Office of Investigations 1 Congress Street, Suite 100 Boston, MA 02114-2017 www.mass.gov/dia Applicant Information Please Print Legibly Name (Business/Organization/Individual):_________________________________________________ _ Address:__________________________________________________________________________ City/State/Zip:_____________________________ Phone #:________________________________ . Homeowners who submit this affidavit indicating they are doing all work and then hire outside contractors must submit a new a ff idavit indicating such. Contractors that check this box must attached an additional sheet showing the name of the sub-contractors and state whether or not those entities have employees. If the sub- information. Insurance Company Name:____________________________________________________________________________ Policy # or Self-ins. Lic. #:__________________________________________ Expiration Date:____________________ Job Site Address: City/State/Zip:______________________ Failure to secure coverage as required under Section 25A of MGL c. 152 can lead to the imposition of criminal penalties of a fine up to $1,500.00 and/or one-year imprisonment, as well as civil penalties in the form of a STOP WORK ORDER and a fine of up to $250.00 a day against the violator. Be advised that a copy of this statement may be forwarded to the Office of Investigations of the DIA for insurance coverage verification. I do hereby certify under the pains and penalties of perjury that the information provided above is true and correct. Signature: Date: Phone #: Official use only. Do not write in this area, to be completed by city or town official . City or Town: ___________________________________ Permit/License #_________________________________ Issuing Authority (circle one): 1. Board of Health 2. Building Department 3. City/Town Clerk 4. Electrical Inspector 5. Plumbing Inspector 6. Other ______________________________ Contact Person:_________________________________________ Phone #:_________________________________ Type of project (required): 6. New construction 7. Remodeling 8. Demolition 9. Building addition 10. Electrical repairs or additions 11. Plumbing repairs or additions 12. Roof repairs 13. Other ____________________ 1. I am a employer with _________ employees (full and/or part-time).* 2. I am a sole proprietor or partner- ship and have no employees working for me in any capacity. required.] 3. I am a homeowner doing all work insurance required.] Are you an employer? Check the appropriate box: 4. I am a general contractor and I have hired the sub-contractors listed on the attached sheet. These sub-contractors have comp. insurance. 5. We are a corporation and its officers have exercised their right of exemption per MGL c. 152, §1(4), and we have no comp. insurance required.] Information and Instructions Pursuant to this statute, an employee An employer of the foregoing engaged in a joint enterprise, and including the legal representatives of a deceased employer, or the receiver or trustee of an individual, partnership, association or other legal entity, employing employees. However the owner of a dwelling house having not more than three apartments and who resides therein, or the occupant of the dwelling house of another who employs persons to do maintenance, construction or repair work on such dwelling house MGL chapter 152, §every state or local licensing agency shall withhold the issuance or renewal of a license or permit to operate a business or to construct buildings in the commonwealth for any applicant who has not produced acceptable evidence of compliance with the insurance coverage required Additionally, MGL chapter 152, § enter into any contract for the performance of public work until acceptable evidence of compliance with the insurance Applicants necessary, supply sub-contractor(s) name(s), address(es) and phone number(s) along with their certificate(s) of insurance. Limited Liability Companies (LLC) or Limited Liability Partnerships (LLP) with no employees other than the employees, a policy is required. Be advised that this affidavit may be submitted to the Department of Industrial Accidents for confirmation of insurance coverage. Also be sure to sign and date the affidavit. The affidavit should be returned to the city or town that the application for the permit or license is being requested, not the Department of compensation policy, please call the Department at the number listed below. Self-insured companies should enter their self-insurance license number on the appropriate line. City or Town Officials Please be sure that the affidavit is complete and printed legibly. The Department has provided a space at the bottom of the affidavit for you to fill out in the event the Office of Investigations has to contact you regarding the applicant. Please be sure to fill in the permit/license number which will be used as a reference number. In addition, an applicant that must submit multiple permit/license applications in any given year, need only submit one affidavit indicating current applicant as proof that a valid affidavit is on file for future permits or licenses. A new affidavit must be filled out each year. Where a home owner or citizen is obtaining a license or permit not related to any business or commercial venture (i.e. a dog license or permit to burn leaves etc.) said person is NOT required to complete this affidavit. The Office of Investigations would like to thank you in advance for your cooperation and should you have any questions, please do not hesitate to give us a call. The Commonwealth of Massachusetts Department of Industrial Accidents Office of Investigations 1 Congress Street, Suite 100 Boston, MA 02114-2017 Tel. # 617-727-4900 ext 7406 or 1-877-MASSAFE Fax # 617-727-7749 www.mass.gov/dia Revised 7-2013 City of Northampton Massachusetts DEPARTMENT OF BUILDING INSPECTIONS 212 Main Street ● Municipal Building Northampton, MA 01060 INSPECTOR Louis Hasbrouck Chuck Miller Building Commissioner Assistant Commissioner HOME OWNER EXEMPTION ACKNOWLEDGEMENT The State of Massachusetts allows the homeowner the right under 780CMR 108.3.4 to act as his/her construction supervisor. The state defines “Homeowner” as, “ Person(s) who owns a parcel on which he/she resides or intends to be, a one or two family dwelling, attached or detached structures accessory to such use and/or farm structures. A person who constructs more than one home in a two- year period shall not be considered a home owner.” The building department for the City of Northampton wants any person(s) who seek to use the home owner exemption, to act as their own construction supervisor, to be aware that by doing so you become responsible for compliance with state building codes and regulations. The inspection process requires that the building department be called to inspect work at various stages, which include foundation/footings (before backfill), sonotube holes (before pour), a rough building inspection (before work is concealed), insulation inspection (if required) and a final building inspection. The building department requires these inspections before the work is concealed, failure to secure these inspections can result in failure to obtain a certificate of occupancy until the work can be inspected. If the homeowner hires other trades to perform work (electrical, plumbing & gas) the homeowner will be responsible to make sure that the trades hired secure their proper permits in conjunction to the building permit issued, and that they get their required inspections. Failure of the individual trades to secure the permits and inspections as required can DELAY the project until such time as the proper permits and inspections are made I, __________________________________________________ understand the above. (Home owner /resident’s signature requesting exemption) I will call to schedule all required building inspections necessary for the building permit issued to me. Date_______________________________ Address of work location_____________________________________________________ _____________________________________________________ _____________________________________________________ SHOULD ANY OF THE ABOVE DESCRIBED POLICIES BE CANCELLED BEFORE THE EXPIRATION DATE THEREOF, NOTICE WILL BE DELIVERED IN ACCORDANCE WITH THE POLICY PROVISIONS. INSURER(S) AFFORDING COVERAGE INSURER F : INSURER E : INSURER D : INSURER C : INSURER B : INSURER A : NAIC # NAME:CONTACT (A/C, No):FAX E-MAILADDRESS: PRODUCER (A/C, No, Ext):PHONE INSURED REVISION NUMBER:CERTIFICATE NUMBER:COVERAGES IMPORTANT: If the certificate holder is an ADDITIONAL INSURED, the policy(ies) must have ADDITIONAL INSURED provisions or be endorsed. If SUBROGATION IS WAIVED, subject to the terms and conditions of the policy, certain policies may require an endorsement. A statement on this certificate does not confer rights to the certificate holder in lieu of such endorsement(s). THIS CERTIFICATE IS ISSUED AS A MATTER OF INFORMATION ONLY AND CONFERS NO RIGHTS UPON THE CERTIFICATE HOLDER. THIS CERTIFICATE DOES NOT AFFIRMATIVELY OR NEGATIVELY AMEND, EXTEND OR ALTER THE COVERAGE AFFORDED BY THE POLICIES BELOW. THIS CERTIFICATE OF INSURANCE DOES NOT CONSTITUTE A CONTRACT BETWEEN THE ISSUING INSURER(S), AUTHORIZED REPRESENTATIVE OR PRODUCER, AND THE CERTIFICATE HOLDER. OTHER: (Per accident) (Ea accident) $ $ N / A SUBR WVD ADDL INSD THIS IS TO CERTIFY THAT THE POLICIES OF INSURANCE LISTED BELOW HAVE BEEN ISSUED TO THE INSURED NAMED ABOVE FOR THE POLICY PERIOD INDICATED. NOTWITHSTANDING ANY REQUIREMENT, TERM OR CONDITION OF ANY CONTRACT OR OTHER DOCUMENT WITH RESPECT TO WHICH THIS CERTIFICATE MAY BE ISSUED OR MAY PERTAIN, THE INSURANCE AFFORDED BY THE POLICIES DESCRIBED HEREIN IS SUBJECT TO ALL THE TERMS, EXCLUSIONS AND CONDITIONS OF SUCH POLICIES. LIMITS SHOWN MAY HAVE BEEN REDUCED BY PAID CLAIMS. $ $ $ $PROPERTY DAMAGE BODILY INJURY (Per accident) BODILY INJURY (Per person) COMBINED SINGLE LIMIT AUTOS ONLY AUTOSAUTOS ONLY NON-OWNED SCHEDULEDOWNED ANY AUTO AUTOMOBILE LIABILITY Y / N WORKERS COMPENSATION AND EMPLOYERS' LIABILITY OFFICER/MEMBER EXCLUDED? (Mandatory in NH) DESCRIPTION OF OPERATIONS below If yes, describe under ANY PROPRIETOR/PARTNER/EXECUTIVE $ $ $ E.L. DISEASE - POLICY LIMIT E.L. DISEASE - EA EMPLOYEE E.L. EACH ACCIDENT EROTH-STATUTEPER LIMITS(MM/DD/YYYY)POLICY EXP(MM/DD/YYYY)POLICY EFFPOLICY NUMBERTYPE OF INSURANCELTRINSR DESCRIPTION OF OPERATIONS / LOCATIONS / VEHICLES (ACORD 101, Additional Remarks Schedule, may be attached if more space is required) EXCESS LIAB UMBRELLA LIAB $EACH OCCURRENCE $AGGREGATE $ OCCUR CLAIMS-MADE DED RETENTION $ $PRODUCTS - COMP/OP AGG $GENERAL AGGREGATE $PERSONAL & ADV INJURY $MED EXP (Any one person) $EACH OCCURRENCE DAMAGE TO RENTED $PREMISES (Ea occurrence) COMMERCIAL GENERAL LIABILITY CLAIMS-MADE OCCUR GEN'L AGGREGATE LIMIT APPLIES PER: POLICY PRO-JECT LOC CERTIFICATE OF LIABILITY INSURANCE DATE (MM/DD/YYYY) CANCELLATION AUTHORIZED REPRESENTATIVE ACORD 25 (2016/03) © 1988-2015 ACORD CORPORATION. All rights reserved. CERTIFICATE HOLDER The ACORD name and logo are registered marks of ACORD HIRED AUTOS ONLY 5/2/2024 Cross Insurance – Wakefield, Inc. 401 Edgewater Place, Suite 100 Wakefield, MA 01880 781-914-1000 781-246-2601 www.crossagency.com Evanston Insurance Company 35378 United States Fire Insurance Company 21113 Berkshire Hathaway Homestate Ins Co 20044 A 2,000,000MKLV1ENV10417712/18/2023 12/18/2024 500,000 3 10,000 3 2,000,000 2,000,000 2,000,000 B 138-772685-8 9/15/2023 12/15/2024 1,000,000 3 A MKLV1EFX100779 12/18/2023 12/18/2024 2,000,00033 2,000,000 C BRWC536384 3/15/2024 3/15/2025 3 1,000,000 1,000,000 1,000,000 A Professional Liability - Claims Made MKLV1ENV104177 12/18/2023 12/18/2024 Aggregate: $2,000,000 Each Claim: $1,000,000 Vincent Thorne Cross Insurance – Wakefield, Inc. wakefieldcertificates@crossagency.com Bright Planet Solar Inc 1451 Grafton Street Worcester MA 01604 79828585 City of Northampton 210 Main Street Northhampton MA 01060 79828585 | 581346 | 23-24 MASTER | Marianne Hoysradt | 5/2/2024 1:03:56 PM (EDT) | Page 1 of 1 The Commonwealth of Massachusetts Department of Industrial Accidents Office of Investigations 600 Washington Street Boston, MA 02111 www.mass.gov/dia Workers’ Compensation Insurance Affidavit: Builders/Contractors/Electricians/Plumbers Applicant Information Please Print Legibly Name (Business/Organization/Individual):_________________________________________________ _ Address:__________________________________________________________________________ City/State/Zip:_____________________________ Phone #:________________________________ *Any applicant that checks box #1 must also fill out the section below showing their workers’ compensation policy information.† Homeowners who submit this affidavit indicating they are doing all work and then hire outside contractors must submit a new affidavit indicating such. ‡Contractors that check this box must attached an additional sheet showing the name of the sub-contractors and state whether or not those entities have employees. If the sub-contractors have employees, they must provide their workers’ comp. policy number. I am an employer that is providing workers’ compensation insurance for my employees. Below is the policy and job site information. Insurance Company Name:____________________________________________________________________________ Policy # or Self-ins. Lic. #:__________________________________________ Expiration Date:____________________ Job Site Address: City/State/Zip:______________________ Attach a copy of the workers’ compensation policy declaration page (showing the policy number and expiration date). Failure to secure coverage as required under Section 25A of MGL c. 152 can lead to the imposition of criminal penalties of a fine up to $1,500.00 and/or one-year imprisonment, as well as civil penalties in the form of a STOP WORK ORDER and a fine of up to $250.00 a day against the violator. Be advised that a copy of this statement may be forwarded to the Office of Investigations of the DIA for insurance coverage verification. I do hereby certify under the pains and penalties of perjury that the information provided above is true and correct. Signature: Date: Phone #: Official use only. Do not write in this area, to be completed by city or town official. City or Town: ___________________________________ Permit/License #_________________________________ Issuing Authority (circle one): 1. Board of Health 2. Building Department 3. City/Town Clerk 4. Electrical Inspector 5. Plumbing Inspector 6. Other ______________________________ Contact Person:_________________________________________ Phone #:_________________________________ Type of project (required): 6. New construction 7. Remodeling 8. Demolition 9. Building addition 10. Electrical repairs or additions 11. Plumbing repairs or additions 12. Roof repairs 13. Other____________________ 1. I am a employer with _________ employees (full and/or part-time).* 2. I am a sole proprietor or partner- ship and have no employees working for me in any capacity. [No workers’ comp. insurance required.] 3. I am a homeowner doing all work myself. [No workers’ comp. insurance required.] † Are you an employer? Check the appropriate box: 4. I am a general contractor and I have hired the sub-contractors listed on the attached sheet. These sub-contractors have employees and have workers’ comp. insurance.‡ 5. We are a corporation and its officers have exercised their right of exemption per MGL c. 152, §1(4), and we have no employees. [No workers’ comp. insurance required.] (888)997-4469 450 SOLAR Berkshire Hathaway Homestate Ins Co 3/15/25 888-997-4469 Bright Planet Solar BRWC536384 Commonwealth of Massachusetts Division of Occupational Licensure Board of Building Regulations and Standards Construction Supervisor CS-112439 Expires: 01/12/2026 STEELE HUDSON 42 CONLIN ROAD OXFORD MA 01540 Commissioner Construction Supervisor Unrestricted - Buildings of any use group which contain less than 35,000 cubic feet (991 cubic meters) of enclosed space. Failure to possess a current edition of the Massachusetts State Building Code is cause for revocation of this license. For information about this license Call (617) 727-3200 or visit www.mass.gov/dpl BRIGHT PLANET SOLAR, INC. 1451 GRAFTON STREET WORCESTER, MA 01604 Type: Registration: Expiration: Supplement Card 182102 05/25/2025 Update Address and Return Card. Office of Consumer Affairs & Business Regulation HOME IMPROVEMENT CONTRACTOR TYPE: Supplement Card Expiration 182102 05/25/2025 BRIGHT PLANET SOLAR, INC. STEELE HUDSON 1451 GRAFTON STREET WORCESTER, MA 01604 Undersecretary THE COMMONWEALTH OF MASSACHUSETTS Registration Registration valid for individual use only before the expiration date. If found return to: Office of Consumer Affairs and Business Regulation 1000 Washington Street - Suite 710 Boston, MA 02118 Not valid without signature Office of Consumer Affairs and Business Regulation 1000 Washington Street - Suite 710 Boston, Massachusetts 02118 Home Improvement Contractor Registration THE COMMONWEALTH OF MASSACHUSETTS VICINITY MAPCONSTRUCTION NOTESCONSTRUCTION NOTESA.A LADDER SHALL BE IN PLACE FOR ANY INSPECTIONS IN COMPLIANCE WITH OSHA REGULATIONS.B.PV MODULES ARE NON-COMBUSTIBLE IN NATURE.C.THIS SYSTEM IS A UTILITY INTERACTIVE (GRID CONNECTED) SYSTEM AND DOES NOT HAVE STORAGE BATTERIES (UNLESS SPECIFICALLY INDICATED ON SHEET PV3 & PV3.1).D.A GROUND ELECTRODE SYSTEM WILL BE PROVIDED IN ACCORDANCE WITH NEC 690.47 & 250.50 - 250.166. GROUNDING ELECTRODE SYSTEM OF EXISTING BUILDING MAY BEUSED WHEN BONDED AT THE SERVICE ENTRANCE. IF EXISTING SYSTEM IS INACCESSIBLE OR INADEQUATE, OR IS ONLY METALLIC WATER PIPING, A SUPPLEMENTALGROUNDING ELECTRODE WILL BE USED AT THE INVERTER LOCATION CONSISTING OF A UL LISTED 8FT GROUND ROD WITH ACORN CLAMP. GROUNDING ELECTRODECONDUCTORS SHALL BE NO LESS THAN #8 AWG AND NO GREATER THAN #6 AWG COPPER AND BONDED TO THE EXISTING GROUNDING ELECTRODE TO PROVIDE FOR ACOMPLETE GROUNDING SYSTEM.E.EACH MODULE WILL BE GROUNDED USING THE SUPPLIED CONNECTION POINTS IDENTIFIED IN THE MANUFACTURER'S INSTALLATION INSTRUCTIONS.F.THE EXPOSED METALLIC TABS OF THE SOLAREDGE OPTIMIZERS SHALL BE BONDED AND/OR GROUNDED PER NEC 690.43(A) AND THE MANUFACTURERS' INSTRUCTIONS.G.PROPER ACCESS AND WORKING CLEARANCE AROUND EXISTING AND PROPOSED ELECTRICAL EQUIPMENT WILL BE PROVIDED AS PER NEC 110.26.H.ALTERNATE POWER SOURCE PLACARD SHALL BE PLASTIC, ENGRAVED IN A CONTRASTING COLOR (WHITE). THIS PLAQUE WILL BE PERMANENTLY ATTACHED & UV RESISTANT.I.ALL PLAQUES AND SIGNS WILL BE INSTALLED AS REQUIRED BY 2020 NEC.J.A SMOKE DETECTOR, APPROVED AND LISTED BY THE STATE FIRE MARSHAL, SHALL BE INSTALLED IN EACH DWELLING WHEN A PERMIT FOR ALTERATIONS, REPAIRS ORADDITIONS EXCEEDS $1,000.00. A BATTERY POWERED SMOKE DETECTOR SATISFIES THE REQUIREMENTS FOR A SMOKE DETECTOR. APPROVED COMBINED SMOKE ALARMSAND CARBON DIOXIDE ALARMS SHALL BE ACCEPTABLE. A CARBON MONOXIDE DETECTOR SHALL BE INSTALLED IN THE SPECIFIC EXISTING DWELLING UNIT THAT HAVEATTACHED GARAGES OR FUEL-BURNING APPLIANCES FOR WHICH A PERMIT IS ISSUED FOR ALTERATIONS, REPAIRS OR ADDITIONS EXCEEDING $1,000.00. LISTED SINGLE- ORMULTI-STATION CARBON MONOXIDE ALARMS SHALL BE INSTALLED OUTSIDE OF EACH SEPARATE SLEEPING AREA IN THE IMMEDIATE VICINITY OF THE BEDROOMS AND ONEVERY LEVEL OF A DWELLING UNIT INCLUDING BASEMENTS. COMBINED SMOKE/CARBON MONOXIDE ALARMS MAY BE USED. THE ALARM SHALL RECEIVE ITS PRIMARYPOWER FROM THE BUILDING WIRING EXCEPT IT IS PERMITTED TO BE SOLELY BATTERY OPERATED WHERE REPAIRS OR ALTERATIONS DO NOT RESULT IN THE REMOVAL OFWALL AND CEILING FINISHES OR THERE IS NO ACCESS BY MEANS OF AN ATTIC.K.THE GROUNDING ELECTRODE CONDUCTOR SHALL BE PROTECTED FROM PHYSICAL DAMAGE BETWEEN THE GROUNDING ELECTRODE AND THE PANEL (OR INVERTER) IFSMALLER THAN #6 AWG COPPER WIRE AS PER NEC 250-64B. THE GROUNDING ELECTRODE CONDUCTOR WILL BE CONTINUOUS, EXCEPT FOR SPLICES OR JOINTS AS BUSBARSWITHIN LISTED EQUIPMENT AS PER NEC 250.64C.L.ROOF COVERINGS SHALL BE DESIGNED, INSTALLED, AND MAINTAINED IN ACCORDANCE WITH THE BUILDING CODE OF THE LOCAL JURISDICTION.M.PV SYSTEMS CONNECTION IN THE SWITCH GEAR (PANEL) SHALL BE POSITIONED AT THE OPPOSITE END FROM THE INPUT FEEDER LOCATION OR MAIN CIRCUIT LOCATION ASPER NEC 705.12(B)(3)(2).N.ALL EQUIPMENT SUPPLIED SHALL BE UL LISTED OR LISTED BY A LISTING AGENCY RECOGNIZED BY THE STATE IN WHICH THE SYSTEM IS CONSTRUCTED.O.AC DISCONNECTS SHALL BE IN COMPLIANCE WITH NEC 690.13.P.ALL DC CONDUCTORS SHALL BE 90° RATED THHW, THWN-2, USE-2 OR PV WIRE. ALL AC CONDUCTORS SHALL BE 75° RATED THWN WIRE.Q.THE UTILITY DISCONNECT HAS VISIBLE BLADES, IS LOCKABLE AND IS ACCESSIBLE TO THE UTILITY 24/7.R.ALL BREAKERS SHALL BE SUITABLE FOR BACKFEED. WHEN BACKFED BREAKER IS THE METHOD OF UTILITY INTERCONNECTION THE BREAKER SHALL NOT READ 'LINE ANDLOAD'.S.COORDINATE ANY POWER OUTAGE WITH LOCAL UTILITY AND PROPERTY OWNER. NOTIFY UTILITY BEFORE ACTIVATION OF PV SYSTEM.T.CITY BUILDING INSPECTOR SHALL INSPECT ACCESSIBLE STRUCTURAL CONNECTIONS AND THE HOUSE CURRENT SIDE OF THE SYSTEM, ALL OTHER EQUIPMENT SHALL BE ULLISTED AND APPROVED.U.PHOTOVOLTAIC MODULES SHALL NOT BE INSTALLED OVER ANY ATTIC, PLUMBING OR MECHANICAL VENT. PLUMBING VENTS TO EXTEND A MIN OF 6" ABOVE ROOF ORMODULE. NO BLDG, PLBG OR MECH VENTS TO BE COVERED, OBSTRUCTED OR ROUTED AROUND MODULES.V.ROOF ACCESS POINT SHALL BE LOCATED IN AREAS THAT DO NOT REQUIRE THE PLACEMENT OF GROUND LADDERS OVER THE OPENINGS SUCH AS WINDOWS OR DOORS, ANDLOCATED AT A STRONG POINT OF BUILDING CONSTRUCTION. FIELD VERIFY EXACT LOCATION.W.THE DISCHARGE OF POLLUTANTS TO ANY STORM DRAINAGE SYSTEM IS PROHIBITED. NO SOLID WASTE, PETROLEUM BYPRODUCTS, SOIL PARTICULATE, CONSTRUCTIONWASTE MATERIAL OR WASTEWATER GENERATED ON CONSTRUCTION SITE OR BY CONSTRUCTION ACTIVITIES SHALL BE PLACED, CONVEYED OR DISCHARGED INTO THESTREET, GUTTER OR STORM DRAIN SYSTEM.X.ALL WIRING MUST BE PROPERLY SUPPORTED BY DEVICES OR MECHANICAL MEANS DESIGNED AND LISTED FOR SUCH USE AND WIRING MUST BE PERMANENTLY ANDCOMPLETELY HELD OFF OF THE ROOF SURFACE.Y.PAINT SURFACE MOUNTED CONDUIT TO MATCH EXISTING STRUCTURE.------------PROJECT #SYSTEM SIZEDESIGNER:DATE:5/17/2024 7:37:52 AMREVDATEDESCRIPTIONDATE:BRIGHT PLANET SOLAR103A MILLBURY ST,AUBURN MA 01501888-997-4469SIGNATURE:CONTRACTOR LICENSE:TITLE SHEETPV12015Vector Structural Engineering has reviewed the existingstructure with loading from the solar array and screwconnections to the existing framing. The design of theracking system, racking connections, and all otherstructural is by others. Mechanical, architectural, and allother nonstructural aspects of the design are by others.Electrical is by others, unless stamped by Dean Levorsen.VSE Project Number: U1932-1068-24105/17/2024651 W. galena park blvd. ste. 101draper, Utah 84020phone (801) 990-1775www.vectorse.com® 7PV MODULES89CONDUIT RUN IS SURFACE MOUNTED(ACTUAL CONDUIT RUNS TO BEDETERMINED IN THE FIELD)6OPTIMIZER (TYPICAL FOR EACH MODULE)NOT USED5.110NOT USEDJUNCTION BOX ON ROOF (SIZEDETERMINED IN FIELD)0'5'10'SYMBOL LEGEND= FLUE / PLUMBING VENT= MECHANICAL VENTMAIN SERVICE PANELUTILITY METER21INVERTER & INTEGRATED DC DISCONNECT5PV SUB PANEL4AC DISCONNECT34.1NOT USEDFIRE CODE PATHWAYS & SETBACKS3'1'-6"WESNROOF CROOF AROOF B3245NEC 110.2613'3'7968------------PROJECT #SYSTEM SIZEDESIGNER:DATE:5/17/2024 7:37:53 AMREVDATEDESCRIPTIONDATE:BRIGHT PLANET SOLAR103A MILLBURY ST,AUBURN MA 01501888-997-4469SIGNATURE:CONTRACTOR LICENSE:ROOF/SITE PLANPV2Vector Structural Engineering has reviewed the existingstructure with loading from the solar array and screwconnections to the existing framing. The design of theracking system, racking connections, and all otherstructural is by others. Mechanical, architectural, and allother nonstructural aspects of the design are by others.Electrical is by others, unless stamped by Dean Levorsen.VSE Project Number: U1932-1068-24105/17/2024651 W. galena park blvd. ste. 101draper, Utah 84020phone (801) 990-1775www.vectorse.com® ------------PROJECT #SYSTEM SIZEDESIGNER:DATE:5/17/2024 7:37:57 AMREVDATEDESCRIPTIONDATE:BRIGHT PLANET SOLAR103A MILLBURY ST,AUBURN MA 01501888-997-4469SIGNATURE:CONTRACTOR LICENSE:PV3ELECTRICALLINE DIAGRAM/DETAILS NGL2L1NTOUTILITYGRID11UTILITYDISCOVISIBLE BLADELOCKABLEW/UTILITYACCESS 24/7TAP LESSTHAN 25'GNDELECT.NOTE 1CONNECTION MADE VIA SUPPLY SIDEPER NEC 705.11(A) & NEC 230.82(6)8FUSED5GN41J-BOX1MODULES/OPTIMIZERS IN A STRING+-REDBLACKSESESE3MODULES/OPTIMIZERS IN A STRING+-REDBLACKSESESEL1L2GL1L25L1L2L1L2GINTEGRATED MODULE & RACKING GND METHOD UL 2703 APPROVED24L1L2GN328.2910.1L1L2GN7.2NPV SUB PANELG541J-BOX1MODULES/OPTIMIZERS IN A STRING+-REDBLACKSESESE3MODULES/OPTIMIZERS IN A STRING+-REDBLACKSESESEL1L2GL1L25L1L2L1L2GINTEGRATED MODULE & RACKING GND METHOD UL 2703 APPROVED24L1L2GN328.2910.1------------PROJECT #SYSTEM SIZEDESIGNER:DATE:5/17/2024 7:37:58 AMREVDATEDESCRIPTIONDATE:BRIGHT PLANET SOLAR103A MILLBURY ST,AUBURN MA 01501888-997-4469SIGNATURE:CONTRACTOR LICENSE:PV3.1ELECTRICALLINE DIAGRAM/DETAILS NOTE: PLAQUES SHALL BE ATTACHED TO THE SERVICE EQUIPMENT WITH NON CORROSIVE, POP-RIVETS, SCREWS, OR APPROVED ADHESIVE.LOCATION: MAIN PANELCONDUIT, RACEWAYS & ENCLOSURESLOCATION: MAIN SERVICE PANEL& AC DISCONNECTLOCATION: MAIN SERVICE PANELPV BACK-FED BREAKERLOCATION: MAIN SERVICE PANELPV BACK-FED BREAKERLOCATION: UTILITY METERLOCATION: PV SUB PANEL (IF USED)15611432LOCATION: MAIN SERVICE PANEL / AC DISCONNECT13LOCATION: AC DISCONNECT14LOCATION: DC DISCONNECT/INVERTER #17LOCATION: DC DISCONNECT/INVERTER #2LOCATION: MAIN SERVICE PANELCOMBINATION OF 2 - INVERTERSLOCATION: MAIN SERVICE PANELLOCATION: INVERTER87109 FOR ILLUSTRATION ONLY (NOT ACTUAL MSP)PV SUB PANEL (IF USED)MAIN SERVICE PANELACDISCONNECT(IF USED)PLACARDINVERTERCONDUITS/RACEWAYS56101719112311248131413LOCATION: MAIN SERVICE PANELPV BACK-FED BREAKER2------------PROJECT #SYSTEM SIZEDESIGNER:DATE:5/17/2024 7:38:03 AMREVDATEDESCRIPTIONDATE:BRIGHT PLANET SOLAR103A MILLBURY ST,AUBURN MA 01501888-997-4469SIGNATURE:CONTRACTOR LICENSE:EQUIPMENTLABELSPV4 PLACARD12SOLARINVERTER & DCDISCONNECTUTILITY METERINGUTILITY ACDISCONNECTCAUTION:MULTIPLE SOURCES OF POWER------------PROJECT #SYSTEM SIZEDESIGNER:DATE:5/17/2024 7:38:03 AMREVDATEDESCRIPTIONDATE:BRIGHT PLANET SOLAR103A MILLBURY ST,AUBURN MA 01501888-997-4469SIGNATURE:CONTRACTOR LICENSE:PLACARDPV4.1 =5'-7"4'STRUCTURAL FRAMINGMEMBER @ 16" O.C.MOUNT ATTACHMENTENDCLAMP, TYP.3'-5"4'STRUCTURAL FRAMINGMEMBER @ 16" O.C.MOUNT ATTACHMENTENDCLAMP, TYP.------------PROJECT #SYSTEM SIZEDESIGNER:DATE:5/17/2024 7:38:04 AMREVDATEDESCRIPTIONDATE:BRIGHT PLANET SOLAR103A MILLBURY ST,AUBURN MA 01501888-997-4469SIGNATURE:CONTRACTOR LICENSE:ATTACHMENTPLANPV5Vector Structural Engineering has reviewed the existingstructure with loading from the solar array and screwconnections to the existing framing. The design of theracking system, racking connections, and all otherstructural is by others. Mechanical, architectural, and allother nonstructural aspects of the design are by others.Electrical is by others, unless stamped by Dean Levorsen.VSE Project Number: U1932-1068-24105/17/2024651 W. galena park blvd. ste. 101draper, Utah 84020phone (801) 990-1775www.vectorse.com® ECOFASTEN ROCKIT ROOF MOUNT SYSTEMALL DIMENSIONS IN INCHESITEM QTY123PARTS LISTDESCRIPTION1 ROCKIT SMART SLIDE ASSEMBLY2 SELF TAPPING SCREW #12 x 3" LONG W/ A SEALING WASHER ASSEMBLY1 ROCKIT V3 MNT 30 TO 40 MM ASSEMBLY.13Ø0.312.87Ø 0.42Ø 0.553.620.755.250.753.621.192.440.630.810.880.630.810.63SELF TAPPING SCREWBOTTOM VIEWFRONT VIEWSIDE VIEW2.446.75123EXPLODED ISOMETRIC VIEWFRONT VIEWSIDE VIEWNOTE:PLEASE SEE MANUFACTURERS GUIDELINES FOR INSTALLATION REQUIREMENTS.THE PLACEMENT AND NUMBER OF SCREWS SHOWN IS THE MINIMUM NUMBERREQUIRED FOR THE CONNECTION TO THE EXISTING ROOF.CBASEE PV5 FOR STRUCTURALINFORMATION**INSTALLER TO VERIFY RAFTER SIZE & SPACINGROCKIT MOUNT, TYP.SKIRTROOF SURFACEAS OCCURSMANUFACTURER SCREWS FOR ROCKIT SLIDE ASSEMBLYNOTES:·SHALL BE AT LEAST 6" FROM ANY TRUSS JOINTS·#12 X 3" LONG, FULLY THREADED, SELF TAPPING SCREW, PER MANUFACTURER·INSTALL PER MANUFACTURERS GUIDELINESROCKIT MOUNTTOP VIEWABCROCKIT MOUNT SIDEROCKIT COUPLING SIDEROCKIT SMART SLIDE DETAIL SIDEDEFROCKIT COUPLING PLANROCKIT MOUNT PLANROCKIT SMART DETAIL FRONTPV MODULE, TYP.ROCKITSMART SLIDEPV MODULE, TYP.ROCKIT COUPLINGROCKIT MOUNTPV MODULE, TYP.ROOF SURFACEAS OCCURSDFEPV MODULE,TYP.ROCKIT MOUNT,TYP.ROOF SURFACEAS OCCURSLL/3 MAX11/16"1 5/16"BETWEENMODULESBETWEENMODULESPV MODULEFRAME, TYP.PV MODULEFRAMEROCKIT MOUNTROCKIT MOUNTPV MODULEROOF SURFACEAS OCCURS1 5/16"BETWEENMODULESNTSNTSNTSNTSNTSNTSSEE PV5 FOR STRUCTURALINFORMATION**INSTALLER TO VERIFY RAFTER SIZE & SPACING3.751.50TYP.0.31TYP.------------PROJECT #SYSTEM SIZEDESIGNER:DATE:5/17/2024 7:38:05 AMREVDATEDESCRIPTIONDATE:BRIGHT PLANET SOLAR103A MILLBURY ST,AUBURN MA 01501888-997-4469SIGNATURE:CONTRACTOR LICENSE:STRUCTURALCOMPONENTSPV6Vector Structural Engineering has reviewed the existingstructure with loading from the solar array and screwconnections to the existing framing. The design of theracking system, racking connections, and all otherstructural is by others. Mechanical, architectural, and allother nonstructural aspects of the design are by others.Electrical is by others, unless stamped by Dean Levorsen.VSE Project Number: U1932-1068-24105/17/2024651 W. galena park blvd. ste. 101draper, Utah 84020phone (801) 990-1775www.vectorse.com® ROOF CROOF AROOF B WESN------------PROJECT #SYSTEM SIZEDESIGNER:DATE:5/17/2024 7:38:05 AMREVDATEDESCRIPTIONDATE:BRIGHT PLANET SOLAR103A MILLBURY ST,AUBURN MA 01501888-997-4469SIGNATURE:CONTRACTOR LICENSE:PROPERTY LINESPV7PROPERTY LINEPROPERTY LINEPROPERTY LINEPROPERTY LINEPROPERTY LINEPROPERTY LINE PROPERTY LINE PROPERTY LINEPROPERTY LINEPROPERTY LINE ROOF CROOF AROOF B INVERTER(S) SERIAL NUMBERS#_______________________#_______________________#_______________________1234578910MAPPING INSTRUCTIONS:121314151. REMOVE THE 'SQUARE' OPTIMIZER STICKERAND PLACE NEATLY ON THE APPROPRIATENUMBERED SPACE.2. WRITE THE CORRESPONDING NUMBER ONTHE APPROPRIATE MODULE WITHIN THE ARRAY.171819202223242527282930323334353738394042434445611162126313641·DO NOT MAKE ANY TIE IN CHANGES UNLESS APPROVED AND DOCUMENTED BY BPS DESIGN TEAM·MAXIMUM WATTAGE ALLOWED IN CIRCUIT/STRING IS 6000W FOR SOLAREDGE INVERTERS 7600-11400·MAXIMUM WATTAGE ALLOWED IN CIRCUIT/STRING IS 5700W FOR SOLAREDGE INVERTERS 3000-6000·MINIMUM OPTIMIZERS IN CIRCUIT/STRING = 8 (6 WITH P405/P505)------------PROJECT #SYSTEM SIZEDESIGNER:DATE:5/17/2024 7:38:06 AMREVDATEDESCRIPTIONDATE:BRIGHT PLANET SOLAR103A MILLBURY ST,AUBURN MA 01501888-997-4469SIGNATURE:CONTRACTOR LICENSE:OPTIMIZERTRACKINGPV8 ROOF CROOF AROOF BDATE / FECHA:CREW LEAD / LIDER DE GRUPO:CREW MEMBERS / MIEMBROS DEL GRUPO:EXCLUSION ZONE/ZONARESTRINGIDAELECTRICAL ZONE/ZONA ELECTRICAXXXXXXXXXXXXXLLADDER/ESCALERAAANCHOR/ANCLAJEANCHORWORK ANGLES/ANCLAJETRABAJADO ENANGULOSVVEHICLES/VEHICULOSHAZARD NUMBER&EXPLAIN/RIESGOSNUMERADOSY EXPLICADOSH#TREE / ARBOLHOMEENTRANCES/ENTRADA DE LACASAESITE NOTES (INCLUDE ANY HAZARD, NUMBERED AND EXPLAINED):NOTAS DEL LUGAR (INCLUYE CUALQUIER RIESGO, NUMERADOY EXPLICADO):CLOSEST URGENT CARE / MEDICAL FACILITY:SALA DE EMERGENCIA / HOSPITAL MAS CERCANO:PUBLIC PROTECTION / PROTECION PUBLICA: EXCLUSION ZONES / ZONA RESTRINGIDA MARKED ENTRYWAYS / ENTRADA MARCADAFALL PROTECTION / PROTECCION DE CAIDAS: ANCHORS / ANCLAJE ROPES / CARABINERS & ROPE GRAB / SOGAS CARABINERO Y AGARRE DE SOGA HARNESS / ARNES LANYARDS / SOGAPPE / EPP: SAFETY GLASSES / GAFAS DE SEGURIDAD GLOVES/GUANTES HARD HATS/CASCO DE SEGURIDAD ARC FLASH SUIT / HOT GLOVES / TRAJE AISLANTE/GUANTES PARA ELECTRICIDAD FIRST AID KIT / KIT DE PRIMEROS AUXILIOS COVID-19 PPE ON SITE / EPP POR COVID EN EL LUGAR CREW ADHERING TO BPS COVID-19 PLAN / AJUSTE EN EL GRUPO AL PLAN POR COVID-19 DE BPSLEGEND /LEYENDAJOB HAZARD ANALYSIS /ANALISIS DE RIESGOS LABORALES------------PROJECT #SYSTEM SIZEDESIGNER:DATE:5/17/2024 7:38:06 AMREVDATEDESCRIPTIONDATE:BRIGHT PLANET SOLAR103A MILLBURY ST,AUBURN MA 01501888-997-4469SIGNATURE:CONTRACTOR LICENSE:JOB HAZARDANALYSISPV9 PICKED BY:RECEIVED BY:------------PROJECT #SYSTEM SIZEDESIGNER:DATE:5/17/2024 7:38:07 AMREVDATEDESCRIPTIONDATE:BRIGHT PLANET SOLAR103A MILLBURY ST,AUBURN MA 01501888-997-4469SIGNATURE:CONTRACTOR LICENSE:BOM SHEETPV10 ® VSE Project Number: U1932.1068.241 May 17, 2024 Bright Planet Solar ATTENTION: Mikey Heinz 103A Millbury St. Auburn, MA 01501 REFERENCE: Humphrey, Albert Residence: 967 Florence Road, Northampton, MA 01062 Bright Planet Solar Project: BPS379308 Solar Array Installation To Whom It May Concern: We have reviewed the existing structure at the above referenced site.The purpose of our review was to determine the adequacy of the existing structure to support the proposed installation of solar panels on the roof as shown on the panel layout plan. Based upon our review, we conclude that the existing structure is adequate to support the proposed solar panel installation. Design Parameters Code: Massachusetts State Residential Code (780 CMR Chapter 51, 9th Edition (2015 IRC)) Risk Category: II Design wind speed, Vult: 40 mph (3-sec gust) Wind exposure category: C Ground snow load, Pg: 40 psf Flat roof snow load, Pf: 35 psf Existing Roof Structure Roof structure: 2x6 rafters @ 16" o.c. Roofing material: asphalt (composite) shingles Roof pitch: 5:12 Connection to Roof Mounting connection: (1) Ecofasten Rockit Smartslide w/(2) #12 screws into framing at max. 48" o.c. (portrait and landscape) along panel edges This installation uses a rail-less system. Panel Orientation: Mixture of portrait and landscape Maximum panel dimension: 76.4x41 in Connections shall be staggered so as not to overload any existing structural member Conclusions Based upon our review,we conclude that the existing structure is adequate to support the proposed solar panel installation. The glass surface of the solar panels allows for a lower slope factor per ASCE 7,resulting in reduced design snow load on the panels.The gravity loads,and thus the stresses of the structural elements,in the area of the solar array are either decreased or increased by no more than 5%.Therefore,the requirements of Section 807.4 of the 2015 IEBC as referenced in 780 CMR Chapter 34, 9th Edition are met and the structure is permitted to remain unaltered. 651 W. Galena Park Blvd., Ste. 101 / Draper, UT 84020 / T (801) 990-1775 / F (801) 990-1776 / www.vectorse.com ® VSE Project Number: U1932.1068.241 Humphrey, Albert Residence 5/17/2024 The solar array will be flush-mounted (no more than 10"above the roof surface)and parallel to the roof surface.Thus,we conclude that any additional wind loading on the structure related to the addition of the proposed solar array is negligible. The attached calculations verify the capacity of the connections of the solar array to the existing roof against wind (uplift), the governing load case.Increases in lateral forces less than 10%are considered acceptable.Thus the existing lateral force resisting system is permitted to remain unaltered. Limitations Installation of the solar panels must be performed in accordance with manufacturer recommendations.All work performed must be in accordance with accepted industry-wide methods and applicable safety standards.The contractor must notify Vector Structural Engineering,LLC should any damage,deterioration or discrepancies between the as-built condition of the structure and the condition described in this letter be found.The use of solar panel support span tables provided by others is allowed only where the building type,site conditions,site-specific design parameters,and solar panel configuration match the description of the span tables.The design of the solar panels,solar racking (mounts,rails,etc.) and electrical engineering is the responsibility of others.Waterproofing around the roof penetrations is the responsibility of others.Vector Structural Engineering assumes no responsibility for improper installation of the solar array.Vector Structural Engineering shall be notified of any changes from the approved layout prior to installation. VECTOR STRUCTURAL ENGINEERING, LLC 05/17/2024 _______________________________________________________ Russ Irion, S.E. MA License: 58425 - Expires: 06/30/2024 Project Engineer Enclosures RTI/wic 05/17/2024 651 W. Galena Park Blvd., Ste. 101 / Draper, UT 84020 / T (801) 990-1775 / F (801) 990-1776 / www.vectorse.com JOB NO.:U1932.1068.241 SUBJECT:WIND PRESSURE ® PROJECT:Humphrey, Albert Residence Label:Note: Calculations per ASCE 7-10 SITE-SPECIFIC WIND PARAMETERS: Basic Wind Speed [mph]:40 Notes: Exposure Category:C Risk Category:II Importance Factor, I: ADDITIONAL INPUT & CALCULATIONS: Height of Roof, h [ft]:25 (Approximate)Hip? Comp/Cladding Location:No Enclosure Classification: Zone 1 GCp:0.9 Figure 30.4-2B (enter negative pressure coefficients) Zone 2 GCp:1.6 Zone 3 GCp:2.5 α:9.5 Table 26.9-1 zg [ft]:900 Table 26.9-1 Kh:0.95 Table 30.3-1 Kzt:1 Equation 26.8-1 Kd:0.85 Table 26.6-1 Velocity Pressure, qh [psf]:3.3 Equation 30.3-1 GCpi:0 Table 26.11-1 PRESSURES:Equation 30.9-1 Zone 1, p [psf]:16.0 psf (1.0 W, Interior Zones, beyond 'a' from roof edge) Zone 2, p [psf]:16.0 psf (1.0 W, End Zones, within 'a' from roof edge) Zone 3, p [psf]:16.0 psf (1.0 W, Corner Zones, within 'a' from roof corner) (a= 3 ft) Solar Panel Array Gable/Hip Roofs 7° < θ ≤ 27° Enclosed Buildings Components and Cladding Wind Calculations ()()piphGCGCqp−= JOB NO.:U1932.1068.241 SUBJECT:CONNECTION ® PROJECT:Humphrey, Albert Residence Calculate Uplift Forces on Connection Pressure (0.6 Dead -0.6 Wind) (psf) Max Trib. Width1 (ft) Max Trib. Area2 (ft2) Max Uplift Force (lbs) Zone 1 7.8 4.0 25.5 199 Zone 2 7.8 4.0 12.7 99 Zone 3 7.8 4.0 12.7 99 Calculate Connection Capacity Connection Description: Ultimate Capacity3 [lbs]:1590 Factor of Safety:3 Quantity per Connection:1 Prying Coefficient:1 Connection Capacity [lbs]:530 Determine Result Maximum Demand [lbs]:199 Connection Capacity [lbs]:530 Result:Capacity > Demand, Connection is adequate. Notes 1. 'Max Trib. Width' is the width along the panel seams tributary to the connection. 3. Ultimate capacity values are from manufacturer testing. 2. 'Max Trib Area' is the product of the 'Max. Trib Width' and the panel width/height perpendicular to the direction of the connection spacing. Tributary area on connections at array edges are reduced by 50% as they Ecofasten Rockit Smartslide w/(2) #12 screws into framing VECTOR STRUCTURAL ENGINEERS JOB NO.:U1932.1068.241 SUBJECT:GRAVITY LOADS ® PROJECT:Humphrey, Albert Residence GRAVITY LOADS Roof Pitch: 5.0 :12 ROOF DEAD LOAD (D) Increase due to pitch Material weight [psf] Asphalt (Composite) Shingles 1.08 2.0 1/2" Plywood 1.08 1.0 Framing 1.00 3.0 Insulation 1.00 0.0 1/2" Gypsum Clg.1.08 0.0 M, E & Misc 1.00 0.0 Total Existing Roof DL PV Array DL 1.08 3 DL:1.08 ROOF LIVE LOAD (Lr) Existing Design Roof Live Load [psf]20 ASCE 7-10 Table 4-1 Roof Live Load With PV Array [psf]20 SNOW LOAD (S):w/ Solar Array Roof Slope [x:12]:5.0 Roof Slope [°]:23 Ground Snow Load, p g [psf]:40 ASCE 7-10, Section 7.2 Terrain Category:C ASCE 7-10, Table 7-2 Exposure of Roof:Fully Exposed ASCE 7-10, Table 7-2 Exposure Factor, Ce:0.9 ASCE 7-10, Table 7-2 Thermal Factor, Ct:1.1 ASCE 7-10, Table 7-3 Risk Category:II ASCE 7-10, Table 1.5-1 Importance Factor, Is:1.0 ASCE 7-10, Table 1.5-2 Flat Roof Snow Load, p f [psf]:35 ASCE 7-10, Equation 7.3-1 Minimum Roof Snow Load, p m [psf]:0 ASCE 7-10, Section 7.3.4 Unobstructed Slippery Surface?Yes ASCE 7-10, Section 7.4 Slope Factor Figure:Figure 7-2b ASCE 7-10, Section 7.4 Roof Slope Factor, Cs:0.79 ASCE 7-10, Figure 7-2 Sloped Roof Snow Load, p s [psf]:28 ASCE 7-10, Equation 7.4-1 Design Snow Load, S [psf]:2835 5.0 23 40 C Fully Exposed 0.9 1.1 II 1.0 35 0 No Figure 7-2b 1.00 35 Design material weight [psf] 2.2 1.1 3.0 0.0 0.0 0.0 6.3 3.3 #VALUE! Existing JOB NO.:U1932.1068.241 SUBJECT:LOAD COMPARISON ® PROJECT:Humphrey, Albert Residence Summary of Loads Existing With PV Array D [psf]6 10 Lr [psf]20 20 S [psf]35 28 Maximum Gravity Loads: Existing With PV Array (D + Lr) / Cd [psf]21 24 ASCE 7-10, Section 2.4.1 (D + S) / Cd [psf]36 32 ASCE 7-10, Section 2.4.1 Maximum Gravity Load [psf]:36 32 Ratio Proposed Loading to Current Loading:90%OK The gravity loads, and thus the stresses of the structural elements, in the area of the solar array are either decreased or increased by no more than 5%. Therefore, the requirements of Section 807.4 of the 2015 IEBC as referenced in 780 CMR Chapter 34, 9th Edition are met and the structure is permitted to remain unaltered. (Cd = Load Duration Factor = 0.9 for D, 1.15 for S, and 1.25 for Lr) 6 BUSBAR CELL TECHNOLOGY 12 BUSBAR CELL TECHNOLOGY BREAKING THE 20 % EFFICIENCY BARRIER Q.ANTUM DUO Z Technology with zero gap cell layout boosts module efficiency up to 20.9 %. THE MOST THOROUGH TESTING PROGRAMME IN THE INDUSTRY Q CELLS is the first solar module manufacturer to pass the most comprehen- sive quality programme in the industry: The new “Quality Controlled PV” of the independent certification institute TÜV Rheinland. INNOVATIVE ALL-WEATHER TECHNOLOGY Optimal yields, whatever the weather with excellent low-light and temperature behavior. ENDURING HIGH PERFORMANCE Long-term yield security with Anti LID Technology, Anti PID Technology1, Hot-Spot Protect and Traceable Quality Tra.Q™. EXTREME WEATHER RATING High-tech aluminum alloy frame, certified for high snow (5400 Pa) and wind loads (4000 Pa). A RELIABLE INVESTMENT Inclusive 25-year product warranty and 25-year linear performance warranty2. 1 APT test conditions according to IEC / TS 62804-1:2015, method A (−1500 V, 96 h) 2 See data sheet on rear for further information. THE IDEAL SOLUTION FOR: Rooftop arrays on residential buildings Q.PEAK DUO BLK ML-G10+ 385-405 ENDURING HIGH PERFORMANCE 76.4 in 1940 mm 43.3 in 1100 mm 48.0 in 1220 mm 1656 lbs 751 kg 24 24 32 α [% / K]+0.04 β [% / K]−0.27 γ [% / K]−0.34 NMOT [°F]109 ± 5.4 (43 ± 3 °C) Hanwha Q CELLS America Inc. 400 Spectrum Center Drive, Suite 1400, Irvine, CA 92618, USA | TEL +1 949 748 59 96 | EMAIL inquiry@us.q-cells.com | WEB www.q-cells.us [V]1000 (IEC) / 1000 (UL)Class II [A DC]20 TYPE 2 [lbs/ft2]75 (3600 Pa) / 55 (2660 Pa) −40 °F up to +185 °F (−40 °C up to +85 °C)[lbs/ft2]113 (5400 Pa) / 84 (4000 Pa) 3 See Installation Manual 385 390 395 400 405 [W]385 390 395 400 405 [A]11.04 11.07 11.10 11.14 11.17 [V]45.19 45.23 45.27 45.30 45.34 [A]10.59 10.65 10.71 10.77 10.83 [V]36.36 36.62 36.88 37.13 37.39 [%]≥ 19.6 ≥ 19.9 ≥ 20.1 ≥ 20.4 ≥ 20.6 [W]288.8 292.6 296.3 300.1 303.8 [A]8.90 8.92 8.95 8.97 9.00 [V]42.62 42.65 42.69 42.72 42.76 [A]8.35 8.41 8.46 8.51 8.57 [V]34.59 34.81 35.03 35.25 35.46 53' 40' HC Certified UL 61730 MECHANICAL SPECIFICATION Format 74.0 in × 41.1 in × 1.26 in (including frame) (1879 mm × 1045 mm × 32 mm) Weight 48.5 lbs (22.0 kg) Front Cover 0.13 in (3.2 mm) thermally pre-stressed glass with anti-reflection technology Back Cover Composite film Frame Black anodized aluminum Cell 6 × 22 monocrystalline Q.ANTUM solar half cells Junction Box 2.09-3.98 in × 1.26-2.36 in × 0.59-0.71 in (53-101 mm × 32-60 mm × 15-18 mm), IP67, with bypass diodes Cable 4 mm² Solar cable; (+) ≥ 49.2 in (1250 mm), (−) ≥ 49.2 in (1250 mm) Connector Stäubli MC4; IP68 Note: Installation instructions must be followed. See the installation and operating manual or contact our technical service department for further information on approved installation and use of this product. Specifications subject to technical changes © Q CELLS Q.PEAK DUO BLK ML-G10+_385-405_DA_2022-02_Rev01_NAELECTRICAL CHARACTERISTICS POWER CLASS MINIMUM PERFORMANCE AT STANDARD TEST CONDITIONS, STC1 (POWER TOLERANCE +5 W / −0 W)MinimumPower at MPP1 PMPP Short Circuit Current1 ISC Open Circuit Voltage1 VOC Current at MPP I MPP Voltage at MPP VMPP Efficiency1 η MINIMUM PERFORMANCE AT NORMAL OPERATING CONDITIONS, NMOT2 MinimumPower at MPP PMPP Short Circuit Current ISC Open Circuit Voltage VOC Current at MPP I MPP Voltage at MPP VMPP 1Measurement tolerances PMPP ± 3 %; I SC; VOC ± 5 % at STC: 1000 W/m2, 25 ± 2 °C, AM 1.5 according to IEC 60904-3 • 2 800 W/m², NMOT, spectrum AM 1.5 Q CELLS PERFORMANCE WARRANTY PERFORMANCE AT LOW IRRADIANCE At least 98 % of nominal power during first year. Thereafter max. 0.5 % degradation per year. At least 93.5 % of nominal power up to 10 years. At least 86 % of nominal power up to 25 years. All data within measurement toleranc- es. Full warranties in accordance with the warranty terms of the Q CELLS sales organisation of your respective country. Typical module performance under low irradiance conditions in comparison to STC conditions (25 °C, 1000 W/m²) TEMPERATURE COEFFICIENTS Temperature Coefficient of ISC Temperature Coefficient of VOC Temperature Coefficient of PMPP Nominal Module Operating Temperature PROPERTIES FOR SYSTEM DESIGN Maximum System Voltage VSYS PV module classification Maximum Series Fuse Rating Fire Rating based on ANSI / UL 61730 Max. Design Load, Push / Pull3 Permitted Module Temperature on Continuous DutyMax. Test Load, Push / Pull3 NA DETAIL A 0.63" (16 mm) 0.33" (8.5 mm)0.96" (24.5 mm) 42.8" (1088 mm) 74.0" (1879 mm) 4 × Mounting slots (DETAIL A) Frame 41.1" (1045 mm) 39.2" (996 mm) 1.26" (32 mm) 8 × Drainage holes 15.6“ (395.5 mm) 4 × Grounding points ø 0.18" (4.5 mm) Label ≥49.2" (1250 mm) ≥49.2" (1250 mm) EN RELATIVE EFFICIENCYCOMPARED TO NOMINAL POWER [%]YEARS Q CELLS Industry standard for linear warranties* *Standard terms of guarantee for the 10 PV companies with the highest production capacity in 2014 (as at: September 2014) 100 95 90 85 80 155 2520010 98 86 200 400 600 800 1000 110 100 90 80RELATIVE EFFICIENCY [%]IRRADIANCE [W/m²] QUALIFICATIONS AND CERTIFICATES PACKAGING INFORMATION UL 61730, CE-compliant, Quality Controlled PV - TÜV Rheinland, IEC 61215:2016, IEC 61730:2016, U.S. Patent No. 9,893,215 (solar cells),Horizontal packaging pallets pallets modules POWER OPTIMIZERSolarEdge Power Optimizer Module Add-On For North America P320 / P370 / P400 / P405 Specifically designed to work with SolarEdge inverters Up to 25% more energy Superior efficiency (99.5%) Mitigates all types of module mismatch losses, from manufacturing tolerance to partial shading Flexible system design for maximum space utilization Fast installation with a single bolt Next generation maintenance with module-level monitoring Compliant with arc fault protection and rapid shutdown NEC requirements (when installed as part of the SolarEdge system) Module-level voltage shutdown for installer and firefighter safety PV power optimization at the module-level www.solaredge.usUSA ͳ CANADA ͳ 'ERMANY ͳ ITALY ͳ FRANCE ͳ :APAN ͳ CHINA ͳ AUSTRALIA ͳ THE NETHERLANDS ͳ U< ͳ ISRAEL ͳ TUR<EY ͳ SOUTH AFRICA ͳ BUL'ARIA ͳ INDIA OPTIMIZER MODEL (typical module compatibility) P320 (for high-power 60-cell modules) P370 (for higher-power 60 and 72-cell modules) P400 (for 72 & 96-cell modules) P405 (for thin film modules) INPUT Rated Input DC Power(1)320 370 400 405 W Absolute Maximum Input Voltage (Voc at lowest temperature) 48 60 80 125 Vdc MPPT Operating Range 8 - 48 8 - 60 8 - 80 12.5 - 105 Vdc Maximum Short Circuit Current (Isc) 11 10.1 Adc Maximum DC Input Current 13.75 12.63 Adc Maximum Efficiency 99.5 % Weighted Efficiency 98.8 % Overvoltage Category II OUTPUT DURING OPERATION (POWER OPTIMIZER CONNECTED TO OPERATING SOLAREDGE INVERTER) Maximum Output Current 15 Adc Maximum Output Voltage 60 85 Vdc OUTPUT DURING STANDBY (POWER OPTIMIZER DISCONNECTED FROM SOLAREDGE INVERTER OR SOLAREDGE INVERTER OFF) Safety Output Voltage per Power Optimizer 1 ± 0.1 Vdc STANDARD COMPLIANCE EMC FCC Part15 Class B, IEC61000-6-2, IEC61000-6-3 Safety IEC62109-1 (class II safety), UL1741 RoHS Yes INSTALLATION SPECIFICATIONS Maximum Allowed System Voltage 1000 Vdc Compatible inverters All SolarEdge Single Phase and Three Phase inverters Dimensions (W x L x H)128 x 152 x 28 / 5 x 5.97 x 1.1 128 x 152 x 36 / 5 x 5.97 x 1.42 128 x 152 x 50 / 5 x 5.97 x 1.96 mm / in Weight (including cables)630 / 1.4 750 / 1.7 845 / 1.9 gr / lb Input Connector MC4 Compatible MC4 / Amphenol AH4 MC4 Compatible Output Wire Type / Connector Double Insulated; MC4 Compatible Double Insulated; MC4 / Amphenol AH4 Double Insulated; MC4 Compatible Output Wire Length 0.95 / 3.0 1.2 / 3.9 m / ft Operating Temperature Range -40 - +85 / -40 - +185 ˚C / ˚F Protection Rating IP68 / NEMA6P Relative Humidity 0 - 100 % (1) Rated STC power of the module. Module of up to +5% power tolerance allowed. SolarEdge Power Optimizer Module Add-On for North America P320 / P370 / P400 / P405 PV SYSTEM DESIGN USING A SOLAREDGE INVERTER(2)(3) SINGLE PHASE HD-WAVE SINGLE PHASE THREE PHASE 208V THREE PHASE 480V Minimum String Length (Power Optimizers) P320, P370, P400 8 10 18 P405 6 8 14 Maximum String Length (Power Optimizers)25 25 50(4) Maximum Power per String 5700 (6000 with SE7600H-US)5250 6000 12750 W Parallel Strings of Different Lengths or Orientations Yes © SolarEdge Technologies, Inc. All rights reserved. SOLAREDGE, the SolarEdge logo, OPTIMIZED BY SOLAREDGE are trademarks or registered trademarks of SolarEdge Technologies, Inc. All other trademarks mentioned herein are trademarks of their respective owners. Date: 10/2017 V.02. Subject to change without notice. (2) For detailed string sizing information refer to: http://www.solaredge.com/sites/default/files/string_sizing_na.pdf. (3) It is not allowed to mix P405 with P320/P370/P400/P600/P700/P800 in one string. (4) A string with more than 30 optimizers does not meet NEC rapid shutdown requirements; safety voltage will be above the 30V requirement Solar Mounting Solutions RL Universal Railless Residential Roof Mount System Installation Manual snapnrack.com snapnrack.comAn Intro to SnapNrack RL Universal SnapNrack’s primary goal is to provide our customers with the lowest possible installed cost for mounting residential solar modules, without compromising the values the industry has come to expect: ease of use, quality, aesthetics, and safety. Designing with this goal in mind, we are proud to present the SnapNrack RL Universal Solar Mounting System. SnapNrack has created a rail less system combining great features and benefits we are known for, with our Ultra Rail system and the most up to date technical innovation in the industry, thus reducing parts while driving down labor, material, and total installation costs. Designed to work with standard module frames, achieving UL 2703 Listing for Grounding/Bonding and Fire Classification, providing integrated wire management, aesthetics and our industry leading "Snap-In" features, SnapNrack is providing the simplest and most cost effective solar mounting solution on the market with RL Universal and SpeedSeal™ Track. Benefits of Installing the SnapNrack RL Universal System Install With Very Few Parts This elimination of parts leads to a lower estimated system cost for both the installer and home owner. Install RL Universal With One Tool All RL Universal hardware is attached using a standard ½” socket Built in Wire Management and Aesthetics Extensive wire management solutions have been designed specifically for the system that adapts to multiple possible mounting positions. The system is designed to be aesthetically pleasing and sturdy with a skirt that provides considerable strength at the leading edge and an elegant look for those seeking high end looking systems. Install RL Universal with SpeedSeal™ Track SpeedSeal™ Track features an innovative design that incorporates flashing reliability into a single roof attachment. This eliminates loosening layers of composition and removing nails with a pry bar, leading to less damage to the roof, minimized potential roof leaks, and much faster installs. snapnrack.comTable of Contents Project Plans Certification Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Component Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pre-Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Installation Steps System Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Composition Shingle Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 RL Universal Mount & Skirt Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Wire Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 MLPE Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Ridge Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Cantilever Deck Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Grounding Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 List of Approved Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 snapnrack.com Certification Details SnapNrack RL Universal system has been evaluated by Underwriters Laboratories (UL) and Listed to UL Standard 2703 for Grounding/Bonding, and Fire Classification. Grounding/Bonding Only specific components have been evaluated for bonding, and are identified as being in the ground path. The RL Universal components that have been evaluated for bonding are the Mount Assembly, Ridge Mount Assembly, Link Assembly, Skirt, Flash Track, or SpeedSeal™ Track, Ground Lugs, and Smart Clips. The following system components are not required to be bonded to the system based on the exceptions in clause 9.1 of UL 2703 1st Ed.: Skirt Spacer, Umbrella Bolt, Flashing and Positioning Springs. Wire management clips are utilized to route conductors away from these components and must be assembled according to the instructions. This mounting system may be used to ground and/or mount a PV module complying with UL 1703 only when the specific module has been evaluated for grounding and/or mounting in compliance with the included instructions. See Appendix A for the list of modules tested with the RL Universal system for integrated grounding. Ground Lugs have been evaluated to both UL 467 and UL 2703 Listing requirements. The following ground lugs have been approved for use: SnapNrack model 242-02101, 242-92202, and Ilsco models GBL-4DBT and SGB-4. The following components have been evaluated for bonding as the fault current ground path: Mount Assembly, Ridge Mount Assembly, Link Assembly, Flash Track or SpeedSeal™ Track, and Ground Lugs. In order to maintain the Listing for bonding, wire management clips must be assembled to route conductors away from parts that have not been evaluated for bonding. A Listed (QIMS) and Unlisted Component (KDER3) grounding lug, SnapNrack part no. 242-92202, is attached to the module frame flange, Flash Track, SpeedSeal™ Track or Ridge Mount Track for the normal attachment of a Grounding Electrode Conductor, which provides bonding within the system and eventual connection to a Grounding Electrode, as required by the U.S. NEC. Details of part no. 242- 92202 can be found in Volume 1, Section 4, and Volume 2, Section 2. When this method is used, the grounding symbol is stamped onto the body of the ground lug to identify the grounding terminal. An alternate method of grounding, A UL Listed (QIMS) and Unlisted Component (KDER3) grounding lug, SnapNrack part no. 242-02101 is attached to the Flash Track or SpeedSeal™ Track. Details of part no. 242-02101 can be found in Volume 1, Section 4, and Volume 2, Section 1. When this method is used, the grounding symbol is stamped onto the body of the ground lug to identify the grounding terminal. An alternate method of grounding, a UL Listed (KDER and QIMS) grounding lug, Ilsco (E34440 and E354420) model SGB-4 is attached to the module frame flange, Flash Track, SpeedSeal™ Track, or Ridge Mount Track. When this method is used, the grounding terminal is identified by the green colored screws of the lug. An alternate method of grounding, a UL Listed (KDER and QIMS) grounding lug, Ilsco (E34440 and E354420) model GBL-4BDT is attached to the module frame flange through the specified hardware and torque values. When this method is used, the grounding terminal is identified by the green colored set screw of the lug. An alternate method of grounding, Enphase R/C (QIKH2)(QIMS2) model M250, M215 & C250 is bonded to the Listed PV module frame by the Enphase R/C (QIMS2) Model EFM-XXMM anodization piercing mounting/clamping kit. The total roof-mounted PV system is bonded (modules and microinverters) together and the assembly is bonded to ground through the Enphase R/C (QIMS2) Engage Cables; Model ETXX-240, ETXX-208 or ETXX-277, when properly grounded at the service entrance. snapnrack.com R/C (QIMS2), Dynoraxx (E357716) photovoltaic bonding device cat. no. Dynobond is an optional component that may be used with this system. The Dynobond device has been evaluated to provide module to module bonding. The Dynobond device attaches to the frame flange of adjacent modules Listed (QIMS), SnapNrack MLPE Frame Attachment Kit model 242-02151 has been investigated to bond approved MLPE device back plates to frames of modules. Tested MLPE devices include the following: - NRTL Listed, SolarEdge Optimizer Model P300-5NC4ARS, P320-5NC4ARS, P370-5NC4AFS, or P400- 5NC4AFS - Enphase R/C (QIKH2)(QIMS2) M250, M215 & C250 - Enphase – NRTL Listed Microinverter models IQ6-60-2-US, IQIQ7-60-2-US, IQ7-60-B-US - Celestica International – Rapid Shutdown Device models DG-006-F001201x and DG-006-F001401x The following MLPE devices have been evaluated for attachment to the Flash Track and SpeedSeal™ Track using the SnapNrack MLPE Rail Attachment Kit, and the Flash Track and SpeedSeal™ Track have been evaluated for use with Listed (QIMS) and Unlisted Component (KDER3) grounding lug, SnapNrack part no. 242-92202. - SMA – Rapid Shutdown Device model RSB-2S-US-10 Additional MLPE devices were evaluated for attachment to the module with the SnapNrack MLPE Frame Attachment Kit model 242-02151 or through the device mounting means. These devices have not been evaluated for bonding, as the enclosures are entirely polymeric: - Ginlong – Rapid Shutdown Device model Solis-MLRSD-R1-1G and Solis-MLRSD-R2-1G - Tigo – Monitoring Device models TSR-4-F, TSR-4-M, TSR-4-O, TSR-4-S, TS4-R-M-DUO, TS4-R-O-DUO, TS4-R-S-DUO When installing the MLPEs per the specifications in the MLPE Installation section of this manual, the system is bonded to the optimizer backing plate. Fire RL Universal has been investigated for a Class A System Fire Classification for a Steep-Sloped Roof with Type 1 and Type 2 modules. Because the system was tested at 5 inches above the test roof fixture RL Universal can be installed without any height restrictions due to System Fire Classification. See Appendix A for potential module-specific height restrictions due to module temperature. The Skirt is considered an optional component with respect to Fire Classification, as RL Universal maintains the same Fire Classification Rating both with and without the skirt. SnapNrack recommends a periodic re-inspection of the completed installation for loose components, loose fasteners, and any corrosion, such that if found, the affected components are to be immediately replaced. Water Submersion Test SnapNrack SpeedSeal™ Track has been evaluated for water penetration of composition shingle roofing systems by static water pressure head. Test method and apparatus were based on a version of ASTM Designation: E2140 Wind-Driven Rain Test Only the following components have been evaluated for the Wind-Driven Rain Test per UL Subject 2582: SpeedSeal™ Track, Comp Flashing, Composition Umbrella Flashing, Flash Track, Umbrella Bolt. Testing was conducted without roofing sealant and without the Umbrella Bolt Gasket. snapnrack.com 5 RL Universal Structural Components Component Details Composition Flash Track Mount SnapNrack RL Universal Mount assembly including rock in channel nut, Riser, Leveler, Mount clamp, and spring Link SnapNrack RL Universal Link assembly including Link bottom, Link top, Link column spacer, and springs Umbrella Lag SnapNrack Composition Flash Track to be installed with Composition Flashing and Umbrella Lag SnapNrack Umbrella Lag with Umbrella Sealing technology, assembly includes 5/16" Lag screw with EPDM gasket and Umbrella washer Composition Flashing SnapNrack Composition Flashing Skirt SnapNrack RL Universal Skirt in single portrait or double landscape lengths SpeedSeal™ Track SnapNrack SpeedSeal™ Track with advanced sealing technology, assembly includes SpeedSeal™ Track and Sealing Ring 5/16" Lag Screw with Sealing Washer SnapNrack 5/16" Lag with Sealing Washer assembly including standard 5/16" lag screw and sealing washer Skirt Spacers SnapNrack RL Universal Skirt Spacer for 40mm, 38mm, 35mm, 32mm, and 30mm modules. snapnrack.com 6 Component Details Smart Clip XL Wire Saver Module frame cable clip, holds six PV wires or four Enphase IQ-Cable Designed to secure conductors that become loose and hang below the array, holds one conductor Ground Lug R Ground Lug R including bonding channel nut, Ground Lug R PRC, bolt, and split lock washer. Grounding/MLPE Components MLPE Frame Attachment Kit Attaches MLPEs (Module Level Performance Enhancers) and other related equipment to the module frame. Smart Clip Module frame cable clip, holds two PV wires or Enphase IQ-Cables Wire Managements Components Ridge Mount SnapNrack RL Universal Ridge Mount assembly including Ridge Mount Track, Ridge Mount Extension, Leveler, Mount Clamp, and spring RL Universal Structural Components snapnrack.com 7 Component Details q Hardware Description Torque Specification RL Universal ½” bolts; System Leveling Bolt, Drop In/Rock In Channel Nut, Mount Top-Down Clamp, Link Top-Down Clamp 12 ft-lb Ground Lug model 242-92202 to Flash Track, SpeedSeal™ Track, Ridge Mount Track or Module Frame, and Ground Lug model 242-92202 to Grounding Electrode Conductor (6-12 SOL)8 ft-lb Ground Lug model 242-02101 to Flash Track or SpeedSeal™ Track (6-12 SOL)16 ft-lb MLPE Frame Attachment Kit, MLPE Rail Attachment Kit 10 ft-lb SolarEdge Frame Mounted Microinverter Bracket to Module Frame 11 ft-lb Enphase Frame Mounted Microinverter Bracket to Module Frame 13 ft-lb Ground Lug model SGB-4 to module or Flash Track 75 in-lb Ground Lug model SGB-4 to module, Flash Track or SpeedSeal™ Track 75 in-lb Ground Lug model SGB-4 to Grounding Electrode Conductor (4-14 SOL or STR)35 in-lb Ground Lug model GBL-4DBT to module 35 in-lb Ground Lug model GBL-4DBT to Grounding Electrode Conductor (10-14 SOL or STR)20 in-lb Ground Lug model GBL-4DBT to Grounding Electrode Conductor (8 SOL or STR)25 in-lb Ground Lug model GBL-4DBT to Grounding Electrode Conductor (4-6 SOL or STR)35 in-lb Hardware Torque Specifications The recommended torque to be applied to components for proper assembly and bonding are as follows: snapnrack.com 8 Site Survey ò Measure the roof surfaces and develop an accurate drawing, including any obstacles such as chimneys and roof vents. ò If plans for the roof structure are available, verify that the plans match the final structure. ò Identify any roof access or setback areas as required by the local AHJ. ò Identify any construction issues that may complicate the process of locating rafters from the roof surface. ò If you find structural problems such as termite damage or cracked rafters that may compromise the structure’s integrity consult a structural engineer. Pre-Installation Requirements Design Guidance ò PV Designers should account for the 0.75 inch spacing between rows and 1.0 inch spacing between columns of modules when creating the layout. ò Ridge Mounts are required if modules will be installed with the top edge of the modules less than 12 inches from the ridge peak. ò Draw the rafter location on the layout to identify where roof attachments can be installed. ò Determine site conditions for calculating the engineering values, confirm site conditions and code versions comply with local AHJ requirements. ò Reference site conditions and system specifications in RL Universal Structural Engineering Report to determine maximum attachment spacing and cantilever values ò Draw roof attachment locations on layout based on maximum attachment spacing and cantilever values X-AXISY-AXIS22'-4"44'-0"11'-2"24'-0" 34'-0" 3'-0"3'-0"(+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-) (+) (-) 27'-6" 22'-0" 16'-6"10'-0"Image note: X-Axis described in this manual is cross-slope on the roof, Y-Axis is in line with the roof slope. Four roof attachments per module are recommended for at least one module per row to provide rigidity in the array. Design Recommendation: Safety Guidance ò Always wear appropriate OSHA approved safety equipment when at active construction site. ò Appropriate fall protection or prevention gear should be used. Always use extreme caution when near the edge of a roof. ò Use appropriate ladder safety equipment when accessing the roof from ground level. ò Safety equipment should be checked periodically for wear and quality issues. ò Always wear proper eye protection when required. ò Staggering rows of attachments on alternating rafters is acceptable, and may provide more evenly distributed loads on the roof structure. ò Identify homerun and Junction Box locations based on rooftop wiring requirements. ò Mark distance from array edge to identifiable roof feature in x and y axes. ò Mark distance from array edge to identifiable roof feature in x and y axes. ò Insert SnapNrack installation details into design plan set specific to the project requirements. snapnrack.com 9 LAYOUT INSTRUCTIONS Required Tools ò Roof Marking Crayon or Chalk ò Tape Measure ò Prybar (Not required with SpeedSeal™ Track) X-AXISY-AXIS22'-4"44'-0"11'-2"24'-0" 34'-0" 1) Transfer the layout to the roof using marking crayon or chalk and identify the outside corners of the array. Draw attachment locations on the roof positioned in the x-axis to land on a rafter and in the y-axis to land between modules rows. 2) (Not required for SpeedSeal™ Track - Flash Track installation only) Use a prybar to loosen layers of composition above proposed attachment locations in preparation for proper flashing placement System Layout Ensure the final roof attachment locations do not exceed the maximum attachment spacing and cantilever specified in the design plan Layout Note: snapnrack.com 10 Required Tools ò Hammer or Stud Finder ò Roof Marking Crayon or Chalk ò Drill with 3/16” Drill Bit ò Roof Sealant ò Socket Wrench ò Torque Wrench ò 1/2” Socket ò Pry Bar (Not required with SpeedSeal™ Track) Composition Shingle Installation Materials Included - Flash Track & Composition Flashing (1) SnapNrack Composition Flashing (1) SnapNrack Flash Track (1) SnapNrack 5/16” SS Umbrella Lag Screw q   q   Materials Included - SpeedSeal™ Track (1) SnapNrack SpeedSeal™ Track Sealing Base (1) 5/16" SS Lag Screw (1) 5/16" SS Washer (Sealing Washer is recommended) q   q   snapnrack.com 11 Composition Shingle Installation INSTALLATION INSTRUCTIONS - FLASH TRACK & COMPOSITION FLASHING 4) Place Flash Track over hole in flashing, drive Umbrella Lag through hole in Flash Track, flashing, and into pilot hole for minimum 2.5” embedment in rafter Composition Flashings should be installed in the nominal position; It is acceptable to install the flashing with leading edge of flashing 1-1/4” above the leading edge of first course of composition, or flush with the leading edge of the first course of composition. Marks on flashing edge are a guide and may be used to simplify installation. Align overlapping composition leading edge with marks. Install Note: Ensure flashing extends minimum (2) courses above base. Best Practice: Apply a U-shape of sealant on top portion of flashing underside. Install Note: 3) Install flashing underneath shingle course directly above pilot hole, align hole in flashing with pilot hole. 2) Apply roofing manufacturer’s approved sealant to lag screw, apply sealant in a circle around pilot hole and fill pilot hole with sealant. MARK FLUSH 1.25" MAX FLUSH 1) Using a Flash Track as a template, drill a pilot hole into the rafter with 3/16” drill bit. snapnrack.com 12 INSTALLATION INSTRUCTIONS - SPEEDSEAL™ TRACK 1) Position SpeedSeal™ Tracks. SpeedSeal™ Tracks must be positioned with the sealant retention ring entirely on one course of composition. EDGE OF SHINGLE COURSE SEALANT RING 3) Turn SpeedSeal™ Track over and fill dam created by foam sealant ring with roof sealant 4) Attach SpeedSeal™ Track to roof using the 5/16” SS lag screw and washer. Roof sealant should be expelled from the underside of the SpeedSeal™ Track as it is installed to assure the proper amount of roof sealant has been applied. If no sealant is expelled, remove SpeedSeal™ Track and add more sealant to the cavity then reinstall on roof. Install Note: SEALANT Composition Shingle Installation 2) Using a SpeedSeal™ Track as a template, drill a pilot hole into the rafter with 3/16” drill bit snapnrack.com 13 Required Tools ò Socket Wrench ò Torque Wrench ò 1/2” Socket ò String Line RL Universal Mount & Skirt Installation Materials Included - RL Universal Mount (1) RL Universal Mount (1) RL Universal Link (1) RL Universal Skirt (1) RL Universal Skirt Spacers q    q    snapnrack.com 14 RL Universal Mount Installation INSTALLATION INSTRUCTIONS 4) To set the RL Universal Mount level loosen the Leveler bolt and move the Leveler up or down, then tighten the Leveler bolt and torque to 12 ft-lb. 5) Run string line along bottom row to align and level RL Universal Mounts between the corner mounts 6) RL Universal Spacers will need to be added to Mounts and Links where Skirt will be installed 1) Install the font row of Mounts by rocking the channel nut on bottom of RL Universal Mount into Flash Track, or SpeedSeal™ Track. 2) Partially tighten Riser bolt to seat the channel nut into the Flash Track, or SpeedSeal™ Track. 3) Slide the bottom two corner Mounts up or down in the Speed- Seal™ Track, or Flash Track until aligned with the bottom edge of array as marked on the roof, then tighten the Riser bolt.Mounts can be installed on either the left or right side of the Flash Track, or SpeedSeal™ Track to avoid any inter- ference with Links Install Note: Use the string line catch and alignment feature on Mounts to hold the string line in place to level and align the Mounts Install Note: Channel nuts must be fully engaged in track and must not extend beyond either end of the track Install Note: snapnrack.com 15 RL Universal Skirt Installation INSTALLATION INSTRUCTIONS 7) Install RL Universal Skirt by holding the skirt in Mount, sliding Skirt to align with array layout marks, and clamping skirt into mount DETAIL K SCALE 2:5 K 8) Use RL Universal Links to connect multiple lengths of Array Skirt DETAIL L SCALE 2:5 L snapnrack.com 16 Wire Management Required Tools ò Socket Wrench ò Torque Wrench ò 1/2” Socket ò Electrician Tools Materials Included (1) Bolt, Hex Cap, 5/16" - 18" X 1", SS (1) SnapNrack Bonding Channel Nut (1) SnapNrack Ground Lug R PRC (1) 5/16" SS Split Lock Washer q  SnapNrack Ground Lug R (242-92101) (1) Smart Clip ((2) PV Wire, (1) Enphase IQ Cable (1) Smart Clip XL ((6) PV Wire, (4) Enphase IQ) (1) Wire Saver ((1) PV Wire) q   Smart Clips q  Smart Clip XL Wire Saver q   Smart Clip    snapnrack.com 17 Wire Management INSTALLATION INSTRUCTIONS - RL GROUND LUG 1) Ground Lug R can be attached to any Flash Track, or SpeedSeal™ Track near the Junction Box. Insert Ground Lug R into Flash Track, or SpeedSeal™ Track. 2) Run 10 – 6 AWG, solid, bare copper GEC into Ground Lug R channel, torque clamping bolt to 16 ft-lb The RL Ground Lug to be used in accordance with the National Electric Code, ANSI/NFPA 70. 3) Run bare, solid EGC from Ground Lug R to Junction Box, bond bare EGC to stranded EGC in Junction Box. For details on installing the Junction Box reference the RL Universal Junction Box Installation Manual. snapnrack.com 18 Wire Management INSTALLATION INSTRUCTIONS - SMART CLIPS 1A) For central inverter and DC to DC MLPE systems: Identify where PV string poles are located, use SnapNrack Smart Clips to manage conductors in route from far pole to the Junction Box 1B) For microinverter systems: Identify route from furthest microinverter to Junction Box, use Smart Clips to manage AC trunk cables and multiple PV wires. Install Note: Use Smart Clips to manage PV module leads connected to the MLPE Route all conductors away from A Mounts and B Mount Bases and Flashings. SmartClips should be used to keep conductors routed away from non-bonded components. SMART CLIP HOME-RUN/TRUNK CABLE PV CONDUCTORS snapnrack.com 19 Required Tools ò Socket Wrench ò Torque Wrench ò 1/2” Socket MLPE & RSD Installation Materials Included (1) SolarEdge Optimizer w/ Frame-Mounted Module Add-On q SolarEdge Frame Mount (1) Enphase Microinverter (1) Enphase Frame Mount q  Enphase Frame Mount SOLAREDGE SOLAREDGE q q  Materials Included - MLPE Rail Attachment Kit (1) SnapNrack MLPE Frame Attachment Top (1) SnapNrack MLPE Frame Attachment Bottom (1) 5/16”-18 X 3/4” Serrated Flange Bolt SS (1) SnapNrack Smart Clip (1) SnapNrack MLPE Frame Attachment Coil Spring SS q     2 3 1 4 5 snapnrack.com 20 MLPE & RSD Installation INSTALLATION INSTRUCTIONS - SNAPNRACK MLPE FRAME ATTACHMENT KIT A 1) Slide the backplate channel of the MLPE device under the MLPE Frame Attachment Kit bolt. The MLPE mounting plate should rest against the MLPE mounting plate backstop on the MLPE Frame Attachment Kit 2) Position the MLPE Frame Attachment Kit on the module frame flange in a location that will not interfere with mounting system components. The module frame flange should rest against the module flange backstop on the MLPE Frame Attachment Kit. A 3) Tighten the mounting bolt on the MLPE Frame Attachment Kit to 10 lb-ft (120 lb-in). Avoid blocking module frame drainage holes when installing the MLPE Frame Attachment Kit. Install Note: 4) Connect the module leads to the input connectors on the MLPE device and manage conductors with the integrated Smart Clip. The MLPE Frame Attachment Kit bonds the following components: Module Frame, MLPE backplate and Smart Clip. Install Note: SnapNrack MLPE Frame Attachment kit are used to attach module level performance enhancing devices, and other devices such an SRD (rapid shutdown device), directly to module frames, and provide integrated grounding/bonding for Devices grounded through metal back plate. (Refer to the list of tested MLPE devices on page 4 of this manual) snapnrack.com 21 MLPE & RSD Installation INSTALLATION INSTRUCTIONS - SOLAREDGE FRAME MOUNT SOLAREDGE 1) Locate the SolarEdge optimizer with Frame-Mounted Module Add- On at a location on the module frame that will not interfere with the RL Universal Mounts. 2) Install the optimizer mounting plate onto the module frame and tighten hardware to 11 ft-lbs. 3) Connect the module leads to the input connectors on the optimizer and manage conductors with SnapNrack Smart Clips. If module is mounted in portrait, install MLPE on long side, short side for landscape. Install Note: INSTALLATION INSTRUCTIONS - ENPHASE FRAME MOUNT 1) Locate the Enphase Frame Mount bracket clamp at a location on the module frame that will not interfere with the RL Universal Mounts. 2) Slide the microinverter unit onto the bracket clamp, then move it slightly to the left. 3) Tighten the hardware to 13 ft-lbs 4) Connect module leads to microinverter DC connectors. The microinverter mounting flange should be on the outside of the module frame. Install Note: Refer to the Enphase Frame Mount installation guide for additional instructions. Install Note: snapnrack.com 22 INSTALLATION INSTRUCTIONS - DECK MOUNTED MLPE & RSD 1) Drill pilot hole into decking with 3/16” drill bit, and apply roofing manufacturer’s approved sealant to lag screw, in a circle around pilot hole, and fill pilot hole with sealant 2) Install flashing underneath shingle course directly above pilot hole aligning hole in flashing with pilot hole. 3) Place Flash Track over hole in flashing parallel with composition course, drive Umbrella Lag through hole in Flash Track, flashing, and into pilot hole MLPE & RSD Installation 4) Insert channel nut of MLPE Attachment Kit into Flash Track, insert back plate of device over the large fender washer, and tighten bolt to 10-16 ft-lb The RL Universal SpeedSeal™ Track can also be used as a means of attaching RSDs, junction boxes, and other hardware to the roof. Install Note: snapnrack.com 23 Required Tools ò Socket Wrench ò Torque Wrench ò 1/2” Socket Module Installation Materials Included SnapNrack RL Universal Link RL Universal Mount Other Materials Required SnapNrack Smart Clip (2-5 per module) SnapNrack Smart Clip XL (10-20 per array) See Wire Management section for details w ➊ ➊ e w e ➋ ➋ snapnrack.com 24 Module Installation INSTALLATION INSTRUCTIONS - BOTTOM ROW 1) Rest downslope edge of module on the Mounts and/or Links position module so side edge is fl ush with marked edge of array layout 3) When module is level with roof slide Mount down the Flash Track, or SpeedSeal™ Track and engage Mount clamp on upslope edge of module 4) With the Mount fully engaged on the module frame fi rst tighten channel nut bolt, then tighten Mount clamp bolt DETAIL M SCALE 1 /2 M 2) Lower upslope edge of module while simultaneously applying slight pressure to seat module into Mounts and/or Links It is recommended that module leads and connectors are prepared for installation using SnapNrack Smart Clips before being brought to the rooftop. • With no MLPE, secure module leads to module frame to allow access to connectors while modules are installed • Secure MLPE device to module frame with SnapNrack MLPE Frame Attachment Kit and connect module leads to MLPE, and manage leads by positioning connectors to allow access during installation Install Note: Channel nuts must be fully engaged in track and must not extend beyond either end of the track. Install Note: snapnrack.com 25 Module Installation INSTALLATION INSTRUCTIONS - BOTTOM ROW 8) Engage Mounts on the module frame and tighten channel nut bolt, then tighten Mount clamp bolt. 9) Repeat steps 5-7 for additional rows of modules in array 5) Install next module in row by placing downslope edge of module onto Links and Mounts then lower upslope edge of module until level with roof 7) Attach Link to upslope side of modules tighten clamp bolts to engage both modules. 6) Slide Mount down the Flash Track, or SpeedSeal™ Track and position the Mount to support the Module Push modules together so they are tight against the Link module spacer Install Note: DETAIL M SCALE 1 /2 M snapnrack.com 26 Ridge Mount Installation INSTALLATION INSTRUCTIONS - RIDGE MOUNT 1) Attach Ridge Mount Track with minimum 2-½” of embedment in to structural member and minimum 5” from Ridge to end of Composition Flashing 2) Slid Ridge Mount Extension into Ridge Mount Track and hand tighten Extension bolt 3) Align up-slope end of Ridge Mount Extension with allay layout as drawn on roof, positioning Extension so that hatched pattern is visible on one side only 4) As the module is lowered into place slide Leveler and clamp assembly down Extension to engage module frame. RIDGE MOUNT, TOP VIEW RIDGE MOUNT, BEYOND MAX. EXTENSION 5) With Module Clamp seated on module frame, first tighten the Leveler bolt then tighten the clamping bolt. RL Ridge Mounts should not be used to extend modules beyond the ridge. Overhanging an adjacent roof is not approved by SnapNrack. Install Note: snapnrack.com 27 Cantilever Deck Mount Installation INSTALLATION INSTRUCTIONS 1) Before attaching Cantilever Deck Mount to roof decking Align Flash Track with module so Mounts will be approximately centered on the Flash Track when clamped or sleeved to the module. A one inch (1”) variance up or down the Flash Track from center is acceptable. ± 1” F R O M C E N T E R 2) Attach flashing and Flash Track to roof decking using a 5/16” x 2” lag screw. If loading conditions require two columns of Cantilever Deck Mounts, it is acceptable to overlap the flashings with a minimum 5-1/2” between holes. 3) For a single column of Cantilever Deck Mounts attach Mount between center of cantilever and end of module making sure distance from mount to end of module is less than maximum allowable cantilever. 1/2 CD CANTILEVER DISTANCE (CD) If roofing is presidential composition, use 5/16” x 2-1/2” lag screws. Install Note: 1/3 CD 1/3 CD CANTILEVER DISTANCE (CD) MIN 5.5 IN 4) With two columns of Cantilever Deck Mounts attach Mounts at approximately 1/3 intervals making sure distance from outside Mount to end of module is less than maximum allowable cantilever. snapnrack.com 28 Grounding Specifications GROUND PATH DETAILS All RL Universal components in the fault current ground path have been Certified to be used multiple times for grounding/bonding. The UL 2703 Listing does not specify a maximum number of uses for the Mount, Link, or Ground Lug. Review the requirements of the National Electrical Code (NEC) Article 250 to select the appropriate Equipment Grounding Conductor size based on the short-circuit current of the PV system When using Ground Lug R the following components are part of the fault current ground path: • SnapNrack, SpeedSeal™ Track • SnapNrack, Flash Track • SnapNrack, Mount Assembly • SnapNrack, Ridge Mount Assembly • SnapNrack, Link • SnapNrack, Skirt 1) Row to row module bonding provided by bonding clip in Mount assembly 2) Column to column bonding provided by bonding clamp in Link assembly. Module heights evaluated for bonding with Link Bonding Clamps: • 40 mm (Canadian, LG, Longi) • 38 mm (REC) • 35 mm, (Longi, Canadian) • 32 mm, (Hanwha) • 30 mm, (REC) 3) Each continuous array is connected to Equipment Grounding Conductor through Ground Lug R installed on one SpeedSeal™ Track, or Flash Track per array SECTION A-A SCALE 1.5 / 1 AA GROUNDING METHOD DETAILS snapnrack.comGrounding Specifications (+) (-) (+) (-) (+) (-) (+) (-) TO EGC LINK GROUND PATH MOUNT GROUND LUG EQUIPMENT GROUNDING CONDUCTOR GROUND PATH DETAILS GROUNDING MARKING DETAILS The Ground Lug R is marked with the ground symbol. snapnrack.com 29 Appendix A The following modules have completed the UL 2703 Listing process for bonding and fire classification and have been approved for use with the RL Universal mounting system by the module manufacturer. Module manufacturer approval letters can be found at www.snapnrack.com. RL Universal has been evaluated for Bonding of the following UL/NRTL Listed PV modules to UL 2703 requirements: Manufacturer Model Wattage Aptos Solar DNA-120-MF23-XXX 320-340 DNA-120-BF23-XXX 320-345 DNA-144-MF23-XXX 390-410 DNA-144-BF23-XXX 390-415 Canadian Solar CS6K-XXX-M 240-335 CS6K-XXX-M-SD 240-305 CS6K-XXX-P 220-320 CS6K-XXX-P-SD 240-300 CS6K-XXX-MS 240-335 CS3K-XXX-P 250-350 CS3K-XXX-MS 280-345 CS3U-XXX-MS 350-420 CS3U-XXX-P 295-420 CS1K-XXX-MS 285-345 CS1H-XXX-MS 310-350 CS1H-XXX-MS-AB 310-350 Hanwha Q Cells Q.PEAK DUO-G5-XXX 290-360 Q.PEAK DUO-BLK-G5-XXX 290-360 Q.PLUS DUO-G5-XXX 290-360 Q.PEAK DUO-G7-XXX 310-350 Q.PEAK DUO-BLK-G7-XXX 290-350 Q.PEAK DUO-G7.2-XXX 310-350 Q.PEAK DUO-G6+-XXX 320-360 Q.PEAK DUO-BLK-G6+-XXX 310-350 Q.PEAK DUO-G6-XXX 320-360 Q.PEAK DUO-BLK-G6-XXX 310-350 Q.PEAK DUO-G8+-XXX 290-360 Q.PEAK DUO-BLK-G8+-XXX 290-360 Q.PEAK DUO-G8-XXX 290-360 Q.PEAK DUO-BLK-G8-XXX 290-360 Q.PEAK DUO BLK-G6+/AC-XXX 340-350 Q.PEAK DUO-ML-G9-XXX 370-390 Q.PEAK DUO-BLK-ML-G9-XXX 365-385 Heliene 60M-XXX 225-325 60P-XXX 200-270 72M-XXX 275-390 72P-XXX 250-350 APPROVED MODULE INFORMATION snapnrack.com 30 Manufacturer Model Wattage JA Solar JAM60S09-XXX/PR 310-325 JAM60S10-XXX/MR 330-345 JAM60S10-XXX/PR 320-335 JAM60S12-XXX/PR 305-320 JAM72S09-XXX/PR 370-395 JAM72S10-XXX/MR 395-415 JAM72S10-XXX/PR 380-405 JAM72S12-XXX/PR 365-385 JAM60S17-XXX/MR 320-330 Jinko Solar JKMXXXM-60 200-305 JKMXXXM-60L 305-325 JKMXXXM-60HL 315-335 JKMXXXM-60HBL 310-330 JKMXXXP-60 200-290 JKMXXXP-60-J4 200-290 JKMXXXP-60-V 200-290 JKMXXXP-60B-J4 200-290 JKMXXXPP-60 200-290 JKMXXXPP-60-V 200-300 JKMXXXM-72 250-365 JKMXXXM-72L-V 370-390 JKMXXXP-72 250-360 JKMXXXP-72-V 250-360 JKMXXXPP-72 250-360 JKMXXXPP-72-V 250-360 JKMSXXXP-72 250-330 JKMXXXM-72HL-V 370-420 JKMXXXM-72HL-TV 380-410 LG LGXXXN1C-A5 320-345 LGXXXN1K-A5 310-355 LGXXXQ1C-A5 340-385 LGXXXQ1K-A5 315-375 LGXXXS1C-A5 280-320 LGXXXN2C-B3 330-340 LGXXXN2W-B3 330-340 LGXXXN1C-G4 280-340 LGXXXN1K-G4 280-300 LGXXXS1C-G4 250-300 LGXXXN2C-G4 360-395 LGXXXN2K-G4 360-385 LGXXXN2W-G4 360-395 LGXXXS2C-G4 300-360 LGXXXS2W-G4 300-360 LGXXXN1C-V5 325-355 LGXXXN1W-V5 325-345 LGXXXN2T-V5 385-430 Appendix A snapnrack.com 31 Appendix A Manufacturer Model Wattage LG LGXXXN2T-J5 385-405 LGXXXN1T-V5 310-340 LGXXXA1C-V5 360-380 Longi LR6-60-XXXM 270-300 LR6-60BK-XXXM 270-300 LR6-60HV-XXXM 270-300 LR6-60PB-XXXM 280-320 LR6-60PE-XXXM 280-320 LR6-60PH-XXXM 280-320 LR6-60HIB-XXXM 295-320 LR6-60HPB-XXXM 295-320 LR6-60HIH-XXXM 300-330 LR6-60HPH-XXXM 300-320 LR4-60HIB-XXXM 335-365 LR4-60HPB-XXXM 335-365 LR4-60HIH-XXXM 350-380 LR4-60HPH-XXXM 350-380 LR4-72HPH-XXXM 420-455 Mission Solar MSEXXXSO5T 260-290 MSEXXXSO5K 270-290 MSEXXXSQ5T 280-300 MSEXXXSQ5K 285-305 MSEXXXMM4J 320-330 MSEXXXMM6J 320-330 MSEXXXSO6W 320-340 MSEXXXSO4J 320-350 MSEXXXSO6J 320-350 MSEXXXSQ6S 345-365 MSEXXXSQ4S 345-365 MSEXXXSR8K 315-335 MSEXXXSR8T 310-330 MSEXXXSR9S 375-400 MSE60AXXX 290-315 Panasonic VBHNXXXKA03 310-325 VBHNXXXKA04 310-325 VBHNXXXSA17 325-335 VBHNXXXSA18 325-335 VBHN325SA17E 325-330 VBHXXXRA18N 325-340 VBHXXXRA03K 320-335 Phono Solar PSXXXM-20/U 270-320 PSXXXMH-20/U 270-320 REC RECXXXTP2 260-300 RECXXXTP2-BLK 260-300 RECXXXTP2M 300-315 RECXXXTP2M 72 350-400 RECXXXTP2M 72 BLK 350-400 snapnrack.com 32 Appendix A Manufacturer Model Wattage REC RECXXXTP2M 72 BLK2 350-400 RECXXXTP2SM 72 350-400 RECXXXTP2SM 72 BLK 350-400 RECXXXTP2SM 72 BLK2 350-400 RECXXXAA 340-380 RECXXXTP3M 295-340 Silfab SLAXXX-M 225-320 SLAXXX-P 225-275 SSAXXX-M 225-300 SSAXXX-P 225-270 SILXXXBL 280-330 SILXXXML 280-320 SILXXXNL 280-320 SLGXXX-M 265-380 SLGXXX-P 265-320 SSGXXX-M 265-360 SSGXXX-P 265-320 SILXXXNT 350-380 SILXXXHL 265-320 Solaria Solaria PowerXT-XXXR-PX 315-385 Solaria PowerXT-XXXR-BX 315-385 Solaria PowerXT-XXXR-AC 315-385 Solaria PowerXT-XXXR-PM 360-440 Solaria PowerXT-XXXR-PM-AC 360-440 Talesun TP660M-XXX 240-300 TP660P-XXX 235-285 TP672M-XXX 290-360 TP672P-XXX 280-345 Trina TSM-XXXDD05(II)260-300 TSM-XXXDD05A.05(II)260-300 TSM-XXXDD05A.08(II)260-300 TSM-XXXDD05A.082(II)260-315 TSM-XXXPA05 215-260 TSM-XXXPA05.05 215-260 TSM-XXXPA05.08 215-260 TSM-XXXPD05 240-280 TSM-XXXPD05.002 215-275 TSM-XXXPD05.05 240-280 TSM-XXXPD05.05S 215-275 TSM-XXXPD05.08 240-280 TSM-XXXPD05.082 215-275 TSM-XXXPD05.08D 245-275 TSM-XXXPD05.08S 215-275 The SnapNrack name and SnapNrack logo are the property of SnapNrack, Inc. All information contained in this document are the property of SnapNrack, Inc. ©2020, SnapNrack, Inc. All rights reserved. snapnrack.com SNR_RL Universal Installation Manual_v1.75 Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 1 159415178v1 About EverBright : Energy is everywhere. Enjoy it without limits. EverBright empowers you to take control of your energy, eliminate uncertainty, and save money by producing and storing your electricity. At EverBright, we believe you should have the freedom to choose how and when you enjoy your energy. Taking Charge of Your Energy $0 $0.325 $470.00 Upfront Payment Cost Per kWh Estimated Monthly Bill Year 1 With this agreement EverBright provides you the following We will maintain the System and make repairs at no additional cost to you. We use a web -enabled performance platform to monitor your System at no additional cost to you. We provide a simple process for transferring the agreement to a new homeowner if you sell your home. Your System is designed to save you money 20.800 kW 17,377 kWh 16,360 kWh 106.21 % System Size Estimated Year 1 Production Estimated Annual Usage Estimated Offset Your estimated 1st year of solar production equals: 19,636 pounds of coal burned THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 2 159415178v1 Frequently Asked Questions What services will we provide? We will insure, monitor, operate, maintain, and repair the System at no cost to you. We will bill you monthly for each month of the Term. Can you end the Agreement early? The Term of the Agreement is 25 years . You are agreeing to buy all energy generated by the System through the Term and any renewals . The only ways to end the Agreement early are if y ou sell your home or if you purchase the System as described in Part II, Section 8 of the Agreement. What happens at the end of the Term? You may purchase the System as described in Part II, Section 8 of the Agreement; or You may ask us to remove the System at no cost to you, as described in Part II, Section 10(c) of the Agreement; or The Agreement may automatically renew for up to ten (10) one -year renewal terms as described in Part II, Section 10(a) of the Agreement. What happens to tax credits, incentives, renewable energy credits and other benefits associated with the System? We will own all federal, s tate , and local tax credits, incentives, renewable energy credits, green tags, carbon offset credits, utility rebates or other attributes of the System; including renewable energy certificates and any similar environmental attributes associated with the el ectricity output from the System. Power Purchase Agreement : Part I Payment Terms & Summary the electric energy generated by II Agreement. This Part I provides answers to some important questions you may have regarding the terms of the Agreement . The answers to the questions below in this Part I are not intended to answer all questions you may have about the Agreement, and only summarize certain terms of the Agreement. Please read the entire Agreement carefully. Property Owner (Customer): ALBERT W HUMPHREY Customer 2 (if any): Property Address: 967 FLORENCE RD FLORENCE, MA 01062 Owner Contact Information: Customer: Phone: 4134787862 Email: Alhump3066@yahoo.com Customer 2 (if any): Phone: Email: Payment Terms: Monthly Payment:* $470.00 3.5% *Plus applicable taxes and fees, if any. Frequently Asked Questions THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 3 159415178v1 What happens if you want to sell your home? You have three options if you sell your home as described in Part II, Section 7 of the Agreement: Assign this Agreement to the buyer of your home if the buyer agrees to assume the obligations herein and either passes our credit criteria or pays a $250 credit check exempt ion fee; or Purchase the System from us; or Prepay all monthly payments through the remaining term of the Agreement, in which case the buyer would not have to pass our credit criteria or pay a credit check exemption fee and would have no additional payment obligations under the Agreement. The Payment Terms outlined above are only valid if you sign and return the Agreement to us within thirty (30) days of May 14, 2024 , which may be extended at our sole discretion. By signing this Agreement in Section 31 , you agree that you: Have read the entire Agreement including any/all E xhibits; Agree to all the terms of the Agreement and the Exhibits, including without limitation the arbitration provisions in Part II, Section 21 of the Agreement; Are eighteen (18) years of age or older; Unless signing as a co -signer, are either a United States resident or are not exempt from paying Federal U.S. income taxes; Are the owner of legal title to the home and that every person or entity with an ownership interest in the home has agreed to be bound by the terms of the Agreement; Have understood that EverBright has the right to obtain and use your consumer report; Agree that EverBright will make a final determination of your eligibility in its sole discretion; Acknowledge that you are responsible for making all payments under the terms of this Agreement; Acknowledge that EverBright will communicate with you via email and that you must maintain a working email address in order to receive these communications; Acknowledge that you are responsible for all obligations set forth in Part II, Section 6 . Acknowledge that you will continue to receive a monthly bill from your local utility; Acknowledge that the System is owned by EverBright and/or its assigns; and Acknowledge that you have been advised of your right to cancel this Agreement. REST OF PAGE INTENTIONALLY LEFT BLANK THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 4 159415178v1 TERMS OF AUTOMATIC RENEWAL PROVIDED THAT (I) YOU ARE NOT IN DEFAULT UNDER THIS AGREEMENT (SEE PART II, SECTION 17 ) AND (II) YOU HAVE NOT GIVEN US WRITTEN NOTICE OF YOUR INTENT TO PURCHASE THE SYSTEM AT THE END OF THE TERM (AS DESCRIBED IN PART II, SECTION 8(A)), THIS AGREEMENT SHALL AUTOMATICALLY RENEW UNLESS WE RECEIVE NOTICE FROM YOU TO THE CONTRARY OR UNTIL THE MAXIMUM NUMBER OF RENEWALS IS REACHED . TO PREVENT AN AUTOMATIC RENEWAL FROM OCCURRI NG, WE MUST RECEIVE FROM YOU WRITTEN NOTICE AT LEAST THIRTY (30), BUT NOT MORE THAN NINETY (90), CALENDAR DAYS BEFORE THE SCHEDULED COMMENCEMENT OF AN AUTOMATIC RENEWAL THAT YOU DO NOT WISH TO RENEW . THIS AGREEMENT SHALL AUTOMATICALLY RENEW AT THE END OF THE TERM FOR ONE (1) ADDITIONAL ONE (1) YEAR RENEWAL TERM AT A MONTHLY PAYMENT EQUAL TO THE MONTHLY PAYMENT FOR YEAR 25 . AT THE END OF THE INITIAL AUTOMATIC RENEWAL TERM AND EACH AUTOMATIC RENEWAL TERM THEREAFTER, THE AGR EEMENT WILL AUTOMATICALLY RENEW FOR ONE (1) AUTOMATIC RENEWAL TERM AT A MONTHLY PAYMENT EQUAL TO THE MONTHLY PAYMENT FOR THE PRIOR AUTOMATIC RENEWAL TERM ESCALATED AT THE APPLICABLE ANNUAL INCREASE RATE, NOT TO EXCEED TEN (10) AUTOMATIC RENEWAL TERMS OR UN TIL WE RECEIVE WRITTEN NOTICE FROM YOU, WHICHEVER OCCURS FIRST. WE WILL SEND YOU A NOTICE AT LEAST FIFTEEN (15), BUT NOT MORE THAN SIXTY (60), CALENDAR DAYS PRIOR TO THE EXPIRATION OF YOUR TIME PERIOD TO PREVENT THE AUTOMATIC RENEWAL TO (I) REMIND YOU OF YOUR END OF TERM OPTIONS AND (II) DISCLOSE TO YOU THE MONTHLY PAYMENT FOR THE FIRST AUTOMATIC RENEWAL TERM AND THE RATE AT WHICH THE MONTHLY PAYMENT WILL AUTOMATICALLY ESCALATE FOR ANY FUTURE AUTOMATIC RENEWAL TERMS . BY SIGNING BELOW, YOU ATTEST THAT YOU CONSENT TO THE TERMS OF AUTOMATIC RENEWAL. Your Signature(s) Property O N ame (Customer): ALBERT W HUMPHREY Customer 2 (if any): Signature: @contact_1_sig_1# Signature: @contact_2_sig_1# Date: @contact_1_datesig_1# Date: @contact_2_datesig_1# THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 5 159415178v1 1. General (a) Introduction . This Agreement is between each Property Owner who signs Part I of this Agreement inverters, energy monitoring systems and other equipment to be installed at your request at the Property Address shown on Part I pursuant to an installation agreement between you an . Because of your agreement to purchase Energy pursuant to this Agreement, EverBright has agreed, at your request, to purchase the System from Installer following installation . EverBright agrees to sell to you, and yo u agree to buy from EverBright, all of the Energy generated by the System on the terms and conditions described in this Agreement. By signing this Agreement, you confirm that you are : I. A Property Owner signing on behalf and with the consent and authorizat ion of all Property Owners of the Property; II. A trustee if the Property is owned by a trust; or III. An attorney in fact or agent authorized under a written power of attorney to sign on behalf of the Property Owners. (b) In -Service Date . -: (i) the System has been installed and is capable of generating Energy, (ii) all permissions and permits necessary to operate the System hav e been obtained, (iii) grid, (iv) all inspections, back -up documentation, and certificates required under applicable law or by the local utility have been provided to EverBright and (v) all conditions listed in Section 11 have been satisfied. (c) Term of Agreement . -Service Date and runs for 25 years (300 full calendar months) plus, if the In -Service Date is not on the first day of a calendar month, the number of days left in that partial calendar month . If the In -Service Date is any day other than the first day of a calendar month, the resulting partial month is included along with the subsequent twelve (12) full calendar months in the first year of the Term . Each subsequent year of the Term begins on the first day of the calendar month immediately after the anniversary date of the In -Service Date. See Section 10 with respect to your rights at the end of the Term, including automatic renewal and the right to purchase the System. (d) Section 7701(e) of the Internal Revenue Code of 1986, as amended. 2. Purchase and Sale of Energy (a) Payments Exhibit B. (b) Monthly Bills. Each month, we will prepare a bill for the preceding billing cycle . You agree that we may send your monthly bills via email unless you contact us directly to request that your monthly bills be sent through the U.S. mail . Power Purchase Agreement : Part II Terms and Conditions REFERENCE INTO THE POWER PURCHASE AGREEMENT : PART I PAYMENT TERMS AND SUMMARY BETWEEN THESE STANDARD TERMS AND PART I, THESE STANDARD TERMS SHALL GOVERN. THESE THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 6 159415178v1 Your billing cycles run on a monthly basis . Your monthly bill will reflect the Monthly Payment from the applicable monthly billing period pl us any applicable taxes and fees . You agree to review each monthly bill promptly for any errors. If you inform us that an error exists on your monthly bill, we will attempt to correct that error prior to your next monthly bill. If you fail to promptly notify us in writing about an error on your monthly bill, we shall bear no liability or responsibility for any losses incurred to the extent permitted by law. Our sole liability to you shall be our obligation to make any appropriate changes after we recei ve your notification. (c) Monthly Payments . The first Monthly Payment due date will be at least thirty (30) calendar days after the In -Service Date . All other Monthly Payments will be due on the same day of each following month as the first Monthly Payment; provided, if the due date of the first Monthly Payment is the last day of the month and such date does not exist in all subsequent months, then each subsequent due date shall be the last day of the applicable month . For example, (i) If the In -Service Date occurs on February 17, the first Monthly Payment will be due no earlier than March 17 and (ii) if the due date for the first Monthly Payment is March 31, then the due date for the second Monthly Payment will be April 30 . We will send you written notice of the first Monthly Payment due date and amount after the In -Service Date. Monthly Payments are payable to us (i) by automatic withdrawal from your checking account or (ii) by check drawn on a U nited States bank account . By providing your automatic payment information where indicated on Exhibit D, you agree to make all Monthly Payments through an automatic payment from your checking account. You agree to send Monthly Payments to us at the addre ss shown on Exhibit D or to any other address or person specified in a written notice we send to you. (d) Additional Energy . If you need more electric energy than is being generated by the System, you will be solely responsible for purchasing that electric en your local utility provider or retail electric supplier. During the term of this Agreement, you should expect to purchase Additional Energy from your local utility or retail electric supplier from time to time. EverBright will not be in default of this Agreement and will not be responsible for any Additional Energy purchased by you to augment the Energy generated by the System. Agreed and accepted by : @contact_1_init_1# (Initials) @contact_2_init_1# (Initials) 3. Monitoring; Other System Use; Data (a) Monitoring . During installation or at any time during the Term, we may install, and from time to time repair or replace, monitoring equipment to monitor the energy production and energy consumption, including at the interconnection point with the local utility company. We will collect monitoring data remotely or use our personnel to collect such informat ion and will make the data available to you upon request. We may also access data regarding your energy consumption from your utility company or from electric usage data storage sites and you agree to execute any necessary third -party access agreement if requested . You agree to allow our personnel access to your Property to collect such information from the monitoring equipment. You agree not to tamper with, damage or modify the energy monitoring equipment in any way. You will be responsible for any dam age or inaccuracies in the energy monitoring equipment that are caused by you or any other person unrelated to EverBright. (b) Other System Uses . energy production and consum ption, as well as for demand response or other utility -based programs designed to reduce your electricity costs or to maintain the reliability of your local electrical grid (if available in your utility area). THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 7 159415178v1 (c) Data Usage and Disclosure . To the extent perm itted by applicable law, we may combine the Energy usage data and System production and performance data with other data, including, without limitation, personally . Our possible uses and disclosure of the Da ta are described in Exhibit E . We will never sell any personally identifiable Data to a third party without your prior written consent. Agreed and accepted by : @contact_1_init_2 # (Initials) @contact_2_init_2 # (Initials) 4. Performance Guarantee (a) Guaranteed Output . Subject to the conditions set forth in this Section 4(a), we guarantee that the System will generate, on a 24 -month basis, no less than the output as set forth in Exhibit . Subject to the conditions set forth in this Sec tion 4(a), we will issue you a credit if the System does not generate the Guaranteed Output. We will not issue you a credit for any System under -performance arisin g from any of the following: (i) Under -performance arising from your failure to comply with your obligations under the Agreement. (ii) Under -performance arising from shading conditions (other than weather) different from those that were present at the Property at t he commencement of installation. (iii) Under -performance as a result of a grid failure disabling the System. (iv) Under -performance arising from you causing or requesting the System to be shut down or to generate significantly less electric energy. (v) Under -performance arising from damage to the System caused by foreign objects acting on the System (hail, golf balls, etc.). WE MAKE NO OTHER REPRESENTATION, WARRANTY OR GUARANTEE OF ANY KIND REGARDING THE ESS OR IMPLIED WARRANTIES ARE HEREBY DISCLAIMED. (b) Over -generation . If, over the course of the Term, the System generates more energy than the Guaranteed Output, then the extra energy will be yours at no additional cost . We may use this over -generation amo unt to offset future under -performance in a given period should the Actual Output attributable to such period be less than the Guaranteed Output attributable to such period. REST OF PAGE INTENTIONALLY LEFT BLANK THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 8 159415178v1 (c) Actual Output and Credits . On the 24 -month anniversary of the In -Service Date and on every 24 -month anniversary thereafter indicated on Exhibit the System during the preceding 24 -month period . For the purposes o mean the amount of Energy generated by the System to date plus any kWh for which you have previously received a credit . Subject to Section 4(a), if the Actual Output is less than the Guaranteed Output for that Guarantee Date set forth on Exhibit C, we will issue you a credit . This credit will be calculated by subtracting the Actual Output for that Guarantee Date from the Guar anteed Output for that Guarantee Date, and multiplying the applicable Credit per kWh for that year set forth on Exhibit C . If the energy monitoring system is malfunctioning or otherwise inoperable for a period of time, we may calculate your Actual Output using the estimated kWh that would have likely been generated during that period based on the projected amount of Energy expected to be generated by the System. Agreed and accepted by : @contact_1_init_3# (Initials) @contact_2_init_3# (Initials) 5. We agree to: (a) utilize a web -based performance monitoring system to accurately measure the amount of Energy the System delivers to you; (b) maintain the System in good operating condition at our cost and expense; (c) insure the S ystem against all damage or loss unless that damage or loss is caused by you, your guests, contractors or agents; and (d) requirements. 6. Your Additional Obligations (a) System and Property Maintenance . You agree to: (i) maintain and make available, at your cost, a functioning indoor internet connection with one AC/D C inverter(s) at all times during the Term; (ii) maintain in good condition and repair the roof of your home and any structural elements or utility interconnections necessary to support the operation of the System; (iii) not move, tamper with, or disturb the System, or permit anyone else to do so, unless previ ously authorized by EverBright in writing ; (iv) not modify, permit or allow structures on your Property in a way that shades, blocks or restricts (v) keep trees, bushes and hedges trimmed so that the System receives as much s unlight as it did when the System was installed; (vi) be responsible for any conditions at your Property that affect the installation or maintenance of the System (e.g., blocking access to the roof, or removing a tree or other natural or man -made object(s) tha t block access to the roof and/or to sunlight) at your sole cost and expense; (vii) prevent damages to the System from foreign objects such as golf balls, frisbees, or rocks; (viii) permit EverBright , after we give you reasonable notice, to inspect the System for proper operation as we reasonably determine necessary; THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 9 159415178v1 (ix) use the Energy the System generates primarily for personal, family, or household purposes, but not to heat a swimming pool (if you have a swimming pool, the load relating to the swimming pool may be excluded for purposes of sizing the System); (x) not remove any markings or identification tags on the System; (xi) not do anything that would, or permit or allow to exist any condition or circumstance that would, cause the System not to operate as intended at the Property or otherwise violate any ; and (xii) pay for any reasonable removal, storage and reinstallation costs in the event the System needs to be removed in order for you to repair or replace the roof on your home; you agree to notify EverBright of the same so that arrangements can be made for such removal, storage and reinstallation. (b) Fees; Late Charges; Checks; Automatic Payment . In addition to the other amounts you agree to pay in this Agreement, you agree to pay the fees as set forth on Exhibit D. In addition, except to the extent prohibited by applicable law, you will also be responsible for any third -party charges we incur in the course of administering this Agreement . If you refinance your mortgage, you will also be responsible for related administrative charges incurred as a result of the refinancing. (c) Taxes . The payments specified in Exhibit B and Exhibit C do not include taxes. (i) If any taxes (including, but not lim ited to, sales and transaction taxes and including any associated interest and penalties) are assessed on these payments, the sale of Energy, the property, or the transaction itself, and are paid by EverBright rather than you, you agree to pay or reimburse EverBright for all such taxes, except to the extent that you are prohibited from doing so by applicable laws. (ii) In addition, you agree to reimburse EverBright for any taxes, including any associated interests and penalties, assessed on the System that EverB right may incur. (iii) To the extent that EverBright seeks reimbursement from you, you agree that EverBright may seek a full reimbursement from you for the total amount incurred by EverBright, impose a surcharge on your monthly invoice to recover the total amoun t incurred by EverBright over a period to be determined by EverBright, or, at its sole discretion, set up a separate payment plan with you to recover the total amount incurred by EverBright. (d) Filings . property under the Uniform Commercial Code and at our reasonable request you will notify any mortgagee or holder of a deed of trust on the Property of the installation and existence of the System and that the System constitutes personal property and not f ixtures (or real property). You also agree that the System is not a real property fixture. However, you agree that EverBright may file UCC -1 financing statements and/or real property fixture filings related to our ownership interest in the System, and an y other notices permitted or required by law . EverBright may assign such filings and any assignee may also file UCC -1 financing statements and/or real property fixture filings related to the System. You also authorize EverBright to make corrections to an y utility paperwork to conform to this Agreement or any revisions or amendments to this Agreement that you and we both agree upon. (e) No Alterations . You agree that you will not make any modifications, improvements, revisions or additions to the System or take any other action that could void any manufacturer warrant ies on the System without ions, improvements, revisions, or additions to the property. (f) Access to the System. (i) EverBright or its representatives shall give you reasonable notice of our need to access the Property whenever commercially reasonable. You grant to EverBright and our employees, agents, representatives, designees and independent contractors (and any inspectors under any THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 10 159415178v1 state incentive program) the right to reaso nably access all of the Property as necessary for the purposes of (A) operating, owning, repairing, maintaining, removing and replacing the System or making any additions to the System or installing complementary technologies on or about the location of the System; (B) (C) taking any other action reasonably necessary in connection with the operation, maintenance, removal or repair of the System . This access right shall continue for up to ninety (90) days after the expiration of this Agreement in order to provide EverBright with reasonable time to remove the System after the end of this Agreement. (ii) During the time that EverBright has access right s, you shall ensure that such access rights are rights. (g) Indemnity . To the fullest extent permitted by law, you shall indemnify, defend, protect, save and hold harmless EverBright, our employees, officers, directors, agents, successors and assigns from any and all third - party claims, actions, costs, expenses (including rea , to the fullest extent allowed by law ), damages, liabilities, penalties, losses, obligations, injuries, demands and liens of any kind or nature arising out of, connected with, relating to or resulting from damage to the System caused by you or your guests, contractors or agents; provided that nothing herein shall require you to indemnify EverBright for our own negligence or willful misconduct . The provisions of this paragraph shall survive termination or expiration of t his Agreement. (h) Monthly Payments . You agree that the obligation to pay all Monthly Payments and all other amounts due under this Agreement shall be absolute and unconditional under all circumstances and shall not be subject to any abatement, defense, count erclaim, setoff, recoupment or reduction for any reason whatsoever, it being the express intent of the parties that all amounts payable by you hereunder shall be and continue to be payable in all events, including by your heirs and estate, and, except as s et forth below in Section 10 and in the accompanying Notice of Cancellation, you hereby waive all rights you may have to reject or cancel this Agreement, to revoke acceptance of the System, or to grant a security interest in the System. (i) Notices. You agree to: (i) notify EverBright immediately upon your discovery of an emergency condition relating to the System, damage to the System or theft of the System; (ii) notify EverBr ight of the sale of your home (see Section 7 below); and (iii) notify EverBright before changing your electric power supplier. See Section 22 for information about sending notices to EverBright. 7. Options When Selling Your Property (a) If you (or your estate or your heirs, as applicable) sell your Property you must choose one of the foll owing three (3) options: (i) Transfer this Agreement and the Monthly Payments . If (A) the person(s) buying your Property -applicable credit requirements or (B) either you or the buyer pays us a $250 credit check exemption fee, then the buyer may sign a transfer agreement assuming all of your rights and obligations under this Agreement, including the obligation to pay Monthly Payments . You will also be responsible for any related administrative charge s we incur as a result of the transfer, such as filing, amending or terminating any UCC or fixture filings. (ii) Purchase the System Outright . Pursuant to Section 8 bel ow. (iii) Prepay the remaining Monthly Payments and Transfer only the Use of the System . If you prepay the remaining Monthly Payments, the person(s) buying your Property will not have to meet any credit requirements and will only need to sign a transfer agreement to assume your rights and obligations (other than the obligation to make Monthly Payments through the Term) under THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 11 159415178v1 this Agreement. The System stays at your Prope rty; the buyer does not have to make any Monthly Payments through the Term (not including any Automatic Renewal Terms) but otherwise will be Agreement will cont inue through the remainder of the Term and as described in Section 10 . (b) If you sell your Property, you must notify us, in writing, at least thirty (30) days, but no more than ninety (90) days, prior to the scheduled closing date indicating which of the options in Section 7(a) you have chosen. (c) If you (or your estate or your heirs, as applicable) sell your Property and do not comply with one of the options in Section 7(a) above, you will be in default under this Agreement. (See Sections 17 and 18 ) 8. Options to Purchase the System (a) You have the option to purchase the System at the following times during the Term: (i) at any time after the sixth (6th) anniversary of the In -Service Date (see Section 1(b) above); (ii) at the end of the Term of this Agreement (see Section 1(c) above); (iii) if you sell your Property during the Term (see Section 7 above); or (iv) discretion) at another time not described above. (b) To purchase the System pursuant to Section 8(a), you must notify us in writing at least thirty (30) days, but no mo re than ninety (90) days, prior to the desired purchase date and deliver payment to EverBright within thirty (30) days of receiving an invoice from EverBright for the purchase price. (c) the greater of : (i) (ii) Exhibit B that corresponds with the year in which the purchase is to occur, plus all applicable taxes and fees relating to the purchase and sale of the System. EverBright will determine Fair Ma rket Value by referencing sources such as an industry guide listing retail prices of used photovoltaic systems installed in your local utility district that are the same as (or substantially similar to) the System, or if no such sources are readily availab le independent appraiser will, on a desktop basis, assume the System will be exchanged between a willing and informed buyer (taking into account an assumption by the buyer of the remaining obligations under this Agreement) and a willing and informed seller, taking into account current and projected market conditions . (d) and EverBright will assign you any product and/or workmanship warranties still in effect for the System. However, EverBright will not provide any maintenance or repair services after you purchase the System, unless you enter into a separate agreement wit h EverBright, at your expense, for such services. If you exercise the option to purchase the System, this Agreement will terminate effective as of the date of such purchase. 9. Option to Prepay Agreement (a) At any time during the Term, you can prepay this Agree ment in full (not including any Automatic Renewal Terms). Such prepayment will not terminate this Agreement, nor limit any of your rights or obligations (other than your obligation to make Monthly Payments during the Term). (b) In order to prepay this Agreeme nt, you must notify us in writing at least thirty (30) days, but no more than based on the following : (i) all accrued but unpaid Monthly Payments, taxes, late charges, penalties, interest and all or any other sums then accrued or due and owing, plus (ii) the amount set forth on Exhibit B in the column System Prepay ment Price ed to present value at five percent (5%) per year), plus (iii) any applicable taxes. THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 12 159415178v1 (c) If you exercise the option to pay the Prepayment Price, any obligations under this Agreement will continue through the remainder of the Term and as described in Section 10 . 10. Options at the End of the Term (a) Automatic Renewal. Provided that (i) you are not in default under this Agreement (see Section 17 ) and (ii) you have not given us written notice of your intent to purchase the System at the end of the Term (as described in Section 8(a)), this Agreement shall automatically renew at the end of the Term for one (1) additional one (1) for year 25 . At the end of the initial Automatic Renewal Term and each Automatic Renewal Term thereafter, the Agreement will automatically renew for one (1) Automatic Renewal Term at a Monthly Payment equal to the Monthly Payment for the prior Automatic Renewal Term escalated at the applicable Annual Increase rate, not to exceed ten (10) Automatic Renewal Terms or until we receive written notice from you as set forth herein, whichever occurs first . See Section 22 for information on how and where to send the written notice . The notice must be received at least thirty (30), but not more than ninety (90), calendar days before the scheduled commencement of an Automati c Renewal Term that you do not wish to renew. EverBright will send you a notice at least fifteen (15), but not more than sixty (60), calendar days prior to the expiration of your time period to prevent the automatic renewal to (i) remind you of your end of term options, and (ii) disclose to you the Monthly Payment for the first Automatic Renewal Term and the rate at which the Monthly Payment will automatically escalate for any future Automatic Renewal Terms. (b) Purchase the System . You also have the right to purchase the System at the end of the Term . See Section 8 for a detailed explanation. (c) If you choose not to renew this Agreement or purchase the System, then EverBright will have the option to remove the System from your Property at no cost to you. (d) If at the end or termination of this Agreement you are in default (see Section 17 ), and EverBright removes the System from your Property, then you agree to pay EverBright the reasonable expense of removing the System from your Property. (e) In the event that we remove the System from your Property for any reason as permitted or contemplated hereunder, we will return the roof area within three inches of the mounting penetrations to a waterproof condition. 11. Termination Rights Prior to Installation of the System (a) Termination of this Agreement Before System I nstallation . the System generates is conditioned on the following items having been completed to our reasonable satisfaction: (i) completion of the engineering site audit (a thorough physical inspection of the Pr operty, including if applicable geotechnical work), and real estate due diligence to confirm the suitability of the Property for the construction, installation and operation of the System; (ii) confirmation of availability of rebates, tax credits, renewable ene rgy credits and other incentives in the amount used to calculate the Energy Price and Monthly Payment amounts set forth in this Agreement; (iii) your meeting our credit underwriting criteria then in effect; (iv) confirmation that EverBright will obtain all applicable benefits referred to in Section 13 ; (v) receipt of all necessary zoning, land use and building permits; and (vi) completion of any renovations, improvements or changes reasonably required on the Property, at your sole cost and expense (e.g., removal of a tree or necessary roof repairs to enable us to safely ins tall the System). THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 13 159415178v1 EverBright may terminate this Agreement without any liability if, in our reasonable judgment, any of the above listed conditions will not be satisfied for reasons beyond our reasonable control. (b) Right to Terminate this Agreement for Signif icant Delays . If, in our reasonable judgment, the installation of the System is not likely to occur in a timely manner for any reason, EverBright may terminate this Agreement by written notice to you, which notice will be effective upon your receipt of su ch notice. (c) Consumer Agreement Revision for Significant Changes . If EverBright recalculates the Guaranteed Output, EverBright may provide you with an updated Part rms affected by the revised estimated output and a summary of the terms changed by such Consumer Agreement Revision. You will have the right to either sign the Consumer Agreement Revision and agree to the revised terms, or terminate this Agreement. 12. Assign ment (a) Assignment by EverBright. EverBright may assign, sell or transfer the System and this Agreement, or any part of this Agreement, without your consent and without notice. Assignment, sale or transfer generally means that EverBright would transfer cert ain of our rights and/or certain of our obligations under this Agreement to another party. any change to your rights and obligations under this Agreement. (b) As signment by You. Except as set forth in this Agreement, you will not assign, sell, pledge or in any other way transfer your interest in the Energy generated by the System, or in this Agreement, without our prior written consent, which shall not be unreaso nably withheld. 13. Our Ownership of the System; Tax Credits and Rebates YOU UNDERSTAND AND AGREE THAT THIS IS NOT A CONTRACT TO SELL OR LEASE THE SYSTEM TO YOU. EVERBRIGHT WILL OWN THE SYSTEM FOR ALL PURPOSES, INCLUDING ANY DATA GENERATED FROM THE SYSTEM. YOU SHALL AT ALL TIMES KEEP THE SYSTEM FREE AND CLEAR OF ALL LIENS, CLAIMS, CHARGES, LEVIES AND LEGAL PROCESSES NOT CREATED BY EVERBRIGHT, AND SHALL AT YOUR EXPENSE PROTECT AND DEFEND EVERBRIGHT AGAINST THE SAME. YOU UNDERSTAND AND AGREE THAT ANY AND ALL FEDERAL, STATE AND LOCAL TAX CREDITS, INCENTIVES, RENEWABLE ENERGY CREDITS, GREEN TAGS, CARBON OFFSET CREDITS, UTILITY REBATES OR ANY OTHER ATTRIBUTES OF THE SYSTEM ARE THE PROPERTY OF AND FOR THE BENEFIT OF EVERBRIGHT, USABLE AT OUR SOLE DISCRETION. EVER BRIGHT SHALL HAVE THE EXCLUSIVE RIGHT TO ENJOY, USE AND TRANSFER ALL SUCH BENEFITS, WHETHER SUCH BENEFITS EXIST NOW OR IN THE FUTURE. YOU AGREE NOT TO CLAIM OR TAKE ANY ACTION OR FAIL TO TAKE SUCH BENEFITS, INCLUDING, WITHOUT LIMITATION, CLAIMING ANY TAX CREDITS WITH RESPECT TO THE SYSTEM ON ANY TAX RETURN AND/OR ENTERING INTO ANY AGREEMENT WITH YOUR UTILITY THAT WOULD ENTITLE YOUR UTILITY TO CLAIM ANY SUCH BENEFITS. YOU AGREE TO REASONABLY CO OPERATE WITH EVERBRIGHT SO THAT WE MAY CLAIM AND TRANSFER ANY FEDERAL, STATE OR LOCAL TAX CREDITS, RENEWABLE ENERGY CREDITS, REBATES, CARBON OFFSET CREDITS OR ANY OTHER BENEFITS FROM THE SYSTEM. THIS MAY INCLUDE TO THE EXTENT ALLOWABLE BY LAW, ENTERING IN TO NET METERING AGREEMENTS, INTERCONNECTION AGREEMENTS, AND FILING RENEWABLE ENERGY/CARBON OFFSET CREDIT REGISTRATIONS AND/OR APPLICATIONS FOR REBATES FROM THE FEDERAL, STATE OR LOCAL GOVERNMENT OR A LOCAL UTILITY AND GIVING OR ASSIGNING THESE TAX CREDITS, RENEWABLE ENERGY/CARBON CREDITS, REBATES OR OTHER BENEFITS OR THEIR CASH EQUIVALENT TO EVERBRIGHT. THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 14 159415178v1 14. Loss or Damage; Insurance (a) Loss or Damage. Unless you or your guests, contractors or agents cause or permit damages to the System, or as otherwise provided in this Agreement, EverBright will bear all of the risk of loss, damage, theft, destruction or similar occurrence to any or all of the System. (b) Insurance . EverBright will insure the System against all damage or loss unless that damage or loss is caused or that covers damage to your Property and provides general liability coverage, but you do not need to add the System to your Property insurance policy. 15. Force Ma jeure; Casualty (a) EverBright is not responsible for any delay or failure in the performance under this Agreement if the delay or failure is due to Force Majeure . earthquakes, sabotage or destruction by a third party of the System, war, riot, acts of a public enemy or other civil disturbance, or a strike, walkout, lockout or other significant labor dispute. (b) If at any time during the Term all or substantially all of the Property and/or the System shall be damaged and/or destroyed by fire or other casualty, EverBright may terminate this Agreement by written notice to you, which termination shall be effective upon receipt of such notice . 16. Limitation of Liability EXCEPT AS EXPRESSLY P ROVIDED IN THIS AGREEMENT, NEITHER PARTY SHALL BE LIABLE TO THE OTHER PARTY FOR ANY SPECIAL, PUNITIVE, EXEMPLARY, INDIRECT, OR CONSEQUENTIAL DAMAGES, ARISING OUT OF OR IN CONNECTION WITH THIS AGREEMENT. EVEN IF A COURT OR ARBITRATOR DECIDES THAT OUR BREAC H OF THIS AGREEMENT OR NEGLIGENCE, FAILURE OF THE SYSTEM, OR A FAILURE OF THE INSTALLATION OR ANY REPAIR PROVIDED BY US CAUSED OR ALLOWED ANY DIRECT HARM OR DAMAGE (WHETHER PROPERTY DAMAGE, PERSONAL INJURY OR DEATH) TO YOU OR ANYONE IN OR ON YOUR PROPERTY, YOU AGREE THAT OUR LIABILITY SHALL BE LIMITED TO THE AMOUNT YOU HAVE PAID US FOR THE ELECTRICITY GENERATED BY THE SYSTEM AND YOU SPECIFICALLY WAIVE ANY OTHER REMEDY AVAILABLE AT LAW OR IN EQUITY. 17. Default YOU WILL BE IN DEFAULT UNDER THIS AGREEMENT IF ANY ONE OF THE FOLLOWING OCCURS: (a) We have not received two or more consecutive Monthly Payments in full by their payment due dates; (b) You or any guarantor makes an assignment for the benefit of creditors, admits in writing your (or any bankruptcy petition is filed by or against you or any guarantor, or you or any guarantor is adjudicated bankrupt or insolvent or undertakes or experiences any substantially similar activity; (c) You have provided any false or misleading financial or other info rmation to obtain this Agreement; (d) You (or your estate or your heirs, as applicable) assign, transfer, encumber, sublet or sell (or attempt to written consent; (e) You fail to perform any material obligation that you have undertaken in this Agreement (which includes doing something you have agreed not to do, including, but not limited to, making any alterations to the System) and such failure continues and is not corrected for a period of fifteen (15) days after written notice; or THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 15 159415178v1 (f) In the event of any foreclosure on your Property not stayed at least thirty (30) days prior to any sale. 18. Additional Action After Default IF YOU ARE IN DEFAULT UNDER THIS AGREEMENT, WE MAY TAKE ANY ONE OR MORE OF THE FOLLOWING ACTIONS AT OUR OPTION AND IN OUR DISCRETION. IF THE LAW REQUIRES US TO DO SO, WE WILL GIVE YOU NOTICE AND WAIT THE STIPULATED PERIOD OF TIME REQUIRED BEFORE TAKING THESE ACTIONS. WE MAY: (a) terminate this Agreement; (b) take any reasonable acti on to correct or cover your default and/or to prevent or reduce our loss (including without limitation costs of repairing damage to the System for which you are responsible); any amount we pay will be added to the amount you owe us and will be immediately due; (c) require you, at your expense, to return the System or make it available to us in a reasonable manner; (d) proceed, by appropriate court or other action, to enforce performance of this Agreement and/or to recover damages for your default (including without to your default, to the fullest extent allowed by law); (e) turn off or take back the System by legal process or self -help, but we may not breach the peace or violate the law; (f) recover fr om you a payment equal to Prepayment Price plus all taxes, late charges, penalties, interest and all other sums then accrued or due and owing to EverBright. After we receive this amount from you, we will (g) use any other remedy available to us in this Agreement or by law or in equity. By choosing any one or more of the remedies described above, EverBright does not give up our right to use another remedy. By deciding not to use any reme dy when you are in default, EverBright does not give up our right to use that remedy (or any other remedy) in case of a subsequent default 19. Warranties (a) (i) Roof Penetration Warranty . We warrant that roof penetrations made by the System and -tight for a period of ten (10) years after installation. (ii) Damage Warranty . We will either repair or reimburse you for damage we cause during installation to the Property, your belongings or your property, as limited by Section 19(b). (b) Warranty Exceptions and Exclusions. (i) The Warranty shall be void and voidable if work is performed by you or your contractors. (ii) The Warranty does not cover any (A) by the System or the associated roof penetrations, (B) pre -existing and/or underlying fai lures of (C) (iii) The Warranty does not apply to the following : (A) work performed or materials used by anyone other than the Installer; (B) any materials that were modified, repaired or attempted to be repaired by anyone other than us, our agents, our representatives, our designees or the Installer without our prior written approval; (C) any damage resulting from your breach of the Agreement; (D) any damage not caused by us, the Installer or a System defect; (E) any damage resulting from THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 16 159415178v1 ordinary wear and tear; (F) any damage resulting from mold, fungus and other organic pathogens; (G) shrinking/cracking of grout and caulking; (H) fading of paints and finishes exposed to sunlight; (I) any damage caused by ball strikes ; and (J) any damage caused by your failure to comply with your obligations under this Agreement . You acknowledge that installation of the System may void any roofing warranty of the roof manufacturer or roof installer . We assume no responsibility if the installation voids your roofing warranty . Before installation, you should check with the roofer or builder concerning any impact the Syst em will have on a roof warranty . You must notify us promptly and in writing of any claim under the Installation Warranty as outlined in Section 22 below . EXCEPT AS SPECIFICALLY DESCRIBED IN THIS AGREEMENT, YOU UNDERSTAND THERE ARE NO REPRESENTATIONS OR WARRANTIES, EXPRESSED OR IMPLIED, AS TO THE MERCHANTABILITY, FITNESS FOR ANY PURPOS E, CONDITION, DESIGN, CAPACITY, SUITABILITY OR PERFORMANCE OF THE SYSTEM OR ITS INSTALLATION. 20. Governing Law The laws of the state where your Property is located shall govern this Agreement without giving effect to conflict of law or choice of law principle s. However, the Federal Arbitration Act governs our agreement to arbitrate (see Section 21 below). 21. Dispute Resolution; Arbitration; Class Action Waiver Informal Dispute Resolution . The parties agree to first try to resolve informally and in good faith any dispute . Accordingly, you agree to send a written notice of the dispute to EverBright at 700 Universe Boulevard, Juno Beach, FL 33408 or support@myeverbright.com or, upon written notice to you, to any address that is later designated by us . We (including our agents, representatives and designees) will send a written notice of dispute to your address liste d on page 2 of the Agreement . If the parties do not reach an informal agreement to resolve the dispute within thirty (30) days after the notice of dispute is received, either party may commence a formal proceeding as detailed below . All applicable statut es of limitation and defenses based upon the passage of time shall be tolled for the thirty (30) days during which the parties try to informally resolve any dispute . If you claim to visually inspect the System and obtain or download pertinent performance data from the System. Arbitration. If the parties cannot resolve any such dispute informally and if either party requests, the other party agrees to arbitrate all related disputes , claims and counterclaims arising out of or relating to this Agreement, the relationships described hereunder, the System, or any alleged or claimed oral or other agreement related to the System. This agreement to arbitrate extends to all claims of any n ature, including, but not limited to, claims for breach of contract, tort claims, claims at law or in equity, or claims arising under statute. If a party seeks to have a dispute settled by arbitration, that party must first send to the other party, by cer tified or registered mail, return receipt requested and postage prepaid, a written Notice of Intent to Arbitrate. If the parties do not reach an agreement to resolve the dispute within thirty (30) days after the Notice is received, either party may commen ce you any arbitration filing fee and, except as provided in the next sentence, EverBright will pay all AAA administration and arbitrator fees. If the arbitrator finds that either the substance of the claim raised by you or the relief sought by you is improper or not warranted, as measured by the standards set forth in Federal Rule of Civil Procedure 11(b), then EverBright will pay these fees on ly if required by the AAA Rules. If the arbitrator grants relief to you that is equal to or greater than the value of what you requested in the arbitration, EverBright bitration . TO THE EXTENT PERMITTED BY LAW, YOU AGREE THAT, BY ENTERING INTO THIS AGREEMENT, YOU AND WE ARE AGREEING TO HAVE DISPUTES DECIDED BY AN ARBITRATOR AND ARE WAIVING THE THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 17 159415178v1 RIGHT TO A TRIAL IN COURT OR BY JURY. IN ADDITION, EACH PARTY MAY BRING CLA IMS AGAINST THE OTHER PARTY ONLY IN ITS INDIVIDUAL CAPACITY AND NOT AS A PLAINTIFF OR CLASS MEMBER IN ANY PURPORTED CLASS OR REPRESENTATIVE PROCEEDING. Further, the parties agree that the arbitrator may not consolidate proceedings for more than one person over any form of a representative or class proceeding, and that if this specific provision is found unenforceable, then the entirety of this arbitration clause shall be null and void (except for the jury trial waive r provision in the first sentence of this paragraph, which shall continue in full force and effect). are applicable to any dispute shall ap ply to any arbitration between us. The arbitrator shall have the authority to award any legal or equitable remedy or relief that a court could order or grant. The arbitrator, however, is not authorized to change or alter the terms of this Agreement or to make any award that would extend to any transaction other than your own . TO THE EXTENT IT IS SUBJECT TO REVIEW IN ACCORDANCE WITH APPLICABLE LAW GOVERNING ARBITRATION AWARDS. OTHER RIGHTS THAT YOU OR WE WOULD HAVE IN COURT MAY ALSO NOT BE AVAILABLE IN ARBITRATION. YOU UNDERSTAND THAT YOU ARE VOLUNTARILY AGREEING TO ARBITRATE DISPUTES ARISING UNDER THIS AGREEMENT AND AUTHORIZE THAT YOU HAVE REVIEWED THIS SECTION AND AGREE TO ITS PROVISIONS: Agreed and accepted by : @contact_1_init_4# (Initials) @contact_2_init_4# (Initials) Class Action Waiver . ARBITRATION MUST BE ON AN INDIVIDUAL BASIS . AS A RESULT, NEITHER YOU NOR EVERBRIGHT MAY JOIN OR CONSOLIDATE CLAIMS IN ARBITRATION BY OR AGAINST OTHER OR MEMBER OF A CLASS OR IN A PRIVATE ATTORNEY GENERAL CAPACITY. Agreed and accepted by : @contact_1_init_5# (Initials) @contact_2_init_5# (Initials) 22. Notices All notices under this Agreement shall be in writing and shall be by personal delivery, electronic mail, online customer portal, overnight courier, or certified, or registered mail, return receipt requested, and deemed received upon personal delivery, acknowledgment of receipt of electronic transmission, the promised delivery date after deposit with overnight courier, or five (5) days after deposit in the mail. You agree that we may provide you wit h notices in electronic format . Each party agrees that a document sent via PDF is deemed to be the same as an original document. Notices from you must include your name, the Property Address shown on page 2 of this Agreement, and the Contract ID# printed at the top of each page of this Agreement . You agree to send written notices to EverBright at 700 Universe Boulevard, Juno Beach, FL 33408 or support@myeverbright.com or, upon written notice to you, to any address that is later designated by us . We will send notices to you using the email or Property Address shown on page 2 of this Agreement unless and until we receive written notice from you of a change to your email or mailing address . You agree that our agents, representatives and other designees may communicate with you directly on our behalf for all purposes relating to the System or this Agreement, including any notices regarding claims we may have. THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 18 159415178v1 You agree that EverBright may call you and send live , pre -recorded and text messages to you, including by use of an automated telephone dialing system, at the phone number you provided regarding the installation, maintenance and administration of your System or this Agreement, even if your phone number is l isted on any Message and data rates may apply. You agree that our agents, representatives and other designees may communicate with you directly on our behalf for all purposes relating to the System or this Agreement, including any notices regarding claims we may have. 23. Privacy/Publicity You grant us the right to publicly use, display, share and advertise the photographic images, System details, price and any other non -personally identifying information of your System. A greed and accepted by : @contact_1_init_6# (Initials) @contact_2_init_6# (Initials) 24. Waiver Any delay or failure of a party to enforce any of the provisions of this Agreement, including but not limited to any remedies listed in this Agreement, or to require performance by the other party of any of the provisions of this Agreement, shall not be co nstrued to (i) or (ii) affect the validity of this Agreement. 25. Accuracy of Information/Credit Reports By signing this Agreement, you represent to us that all of the information you have furnished to us (or have caused others to furnish to us) in connection with this Agreement (including any application for this Agreement) is, to the best of your knowledge, true, complete and accurate, does not include any false or misleading information and does not omit any material, relevant information . You agree that we may obtain employment and income records, credit bureau reports on you, verify your credit references and we may check any of the information provi ded to us from whatever source we choose to verify it . Additionally, upon request, you agree to promptly give us accurate updated financial information about yourself. We may report information about this Agreement to credit bureaus . Late payments, misse d payments, or other defaults on this Agreement may be reflected in your credit report. Credit Report Notice . As required by law, you are hereby notified that a negative credit report reflecting on your credit record may be submitted to a credit reporting agency if you fail to fulfill the terms of your credit obligations. 26. Personal Information and Privacy Policy Please see our Privacy Policy (available at www.goeverbright.com) for more information about how we collect and use personal information . By signi ng this agreement, you acknowledge that you have read, understand and agree with the terms of our Privacy Policy, and that our Privacy Policy may be changed from time to time. THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 19 159415178v1 27. Monitoring and Recording Telephone Call EverBright and others acting on our beha lf may (a) monitor and record telephone calls between you and us regarding this Agreement and (b) use automatic dialing equipment to make calls to you . You agree that we may call you and send pre -recorded and text messages to you at the phone number you provided regarding this Agreement and the installation, maintenance and administration of your System, including by the use of an automated telephone dialing system, even if your phone number is listed on any national or state list . Message and data rates may apply . 28. Calling Agreement You agree that by signing below, you consent that EverBright, its affiliates, and those acting on its/their behalf an automated telephone dialing system and/or a prerecorded message . The types of calls or texts you may receive include advertisements or telemarketing messages concerning our benefits and services . Calls can be made to any number you provide in connect ion or any other matter, even if listed on a national or state Do Not Call registry . You understand that anyone with access to your telephone or email account may listen to or read the messages the Servicing Parties leave or send, and you agree that the Servicing Parties will have no liability for anyone accessing such messages. You understand that consent is not a condition of the pr ovision of services under this Agreement. Agreed and accepted by : @contact_1_init_7# (Initials) @contact_2_init_7# (Initials) 29. Entire Agreement; Survival; Changes; Joint and Several Liability regarding the sale and purchase of Energy generated by the System. There are no other agreements regarding this Agreement, either written or oral. Any change to this Agreement must be in writing and (except to the extent specifically provided to the cont rary in this Agreement) signed by both parties. Captions and headings used in this Agreement are for convenience and reference only, and shall not affect the interpretation of this Agreement . Unless the context specifically requires otherwise, the use of the plural in this Agreement includes the singular, and vice versa. Any rule of construction to the effect that any ambiguities are to be resolved against the drafting party shall not apply to the interpretation of this Agreement, any provisions herein or any amendments hereto . If any portion of this Agreement is determined to be unenforceable, the remaining provisions shall be enforced in accordance with their terms or shall be interpreted or re -written so as to make them enforceable . In addition, in th e event this Agreement becomes subject to utility -type or other regulation by any publi c utility commission or other regulatory agency, you agree to reasonably cooperate with EverBright in restructuring this agreement such that it would no longer be subjec t to such utility -type or other regulation by any public utility commission or other regulatory agency or otherwise to address such regulation. After the termination or expiration of this Agreement, any provisions which by their nature are intended to surv ive such termination or expiration shall survive, including, without limitation, Sections 6 , 13 , 16 , 18 , 19 and 21 . You agree that if more than one person signs this Agreement as a Property Owner or Co -Owner, each of you is fully responsible, individually and together, for performing all of your obligations under this Agreement, a nd we may enforce this Agreement against any one (or all) of you, at our option. Your obligations under this Agreement are binding on you, your legal representatives, and your estate, to the fullest extent allowed by law, unless and THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 20 159415178v1 until we either expres sly release you from your obligations in writing, or we transfer ownership of the System to you. REST OF PAGE INTENTIONALLY LEFT BLANK THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 21 159415178v1 30. Right to Cancel You, the buyer, may cancel this transaction at any time prior to midnight of the TENTH business day after the date of this transaction . See the attached Notice of Cancellation form for an explanation of this right. 31. Signatures BY SIGNING BELOW, YOU ATTEST THAT YOU HAVE RECEIVED A COMPLETELY FILLED -IN COPY OF THIS AGREEMENT , THE EXHIBITS , AND TWO (2) COP IES OF A NOTICE OF CANCELLATION . Your Signature(s) Property O N ame (Customer): ALBERT W HUMPHREY Customer 2 (if any): Signature: @contact_1_sig_1# Signature : @contact_2_sig_1# Date: @contact_1_datesig_1# Date: @ contact_2_datesig_1# EverBright, LLC Date: Title: May 14, 2024 President, EverBright, LLC Signature: Print Name: Jill Dvareckas THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 22 159415178v1 EXHIBIT A TO POWER PURCHASE AGREEMENT (Copy 1) NOTICE OF CANCELLATION May 14, 2024 You may cancel this transaction, without any penalty or obligation, within TEN business days from the above date . If you cancel, any property traded in, any payments made by you under the contract or sale, and any negotiable instrument executed by you wi ll be returned within ten business days following receipt by the seller of your cancellation notice, and any security interest arising out of the transaction will be canceled . If you cancel, you must make available to the seller at your residence, in sub stantially as good condition as when received, any goods delivered to you under this contract or sale; or you may, if you wish, comply risk . If you do make the goods available to the seller and the seller does not pick them up within twenty days of the date of your notice of cancellation, you may retain or dispose of the goods without any further obligation. If you fail to make the goods available t o the seller, or if you agree to return the goods to the seller and fail to do so, then you remain liable for performance of all obligations under the contract . To cancel this transaction, you must mail or deliver a signed and dated copy of this cancella tion notice, or any other written notice, or send a telegram to EverBright, 700 Universe Boulevard, Juno Beach, FL 33408, not later than midnight of May 29, 2024. I hereby cancel this transaction. ______________________________ Date ______________________________ THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 23 159415178v1 EXHIBIT A TO POWER PURCHASE AGREEMENT (Copy 2 ) NOTICE OF CANCELLATION May 14, 2024 You may cancel this transaction, without any penalty or obligation, within TEN business days from the above date . If you cancel, any property traded in, any payments made by you under the contract or sale, and any negotiable instrument executed by you wi ll be returned within ten business days following receipt by the seller of your cancellation notice, and any security interest arising out of the transaction will be canceled . If you cancel, you must make available to the seller at your residence, in sub stantially as good condition as when received, any goods delivered to you under this contract or sale; or you may, if you wish, comply risk . If you do make the goods available to the seller and the seller does not pick them up within twenty days of the date of your notice of cancellation, you may retain or dispose of the goods without any further obligation. If you fail to make the goods available t o the seller, or if you agree to return the goods to the seller and fail to do so, then you remain liable for performance of all obligations under the contract . To cancel this transaction, you must mail or deliver a signed and dated copy of this cancella tion notice, or any other written notice, or send a telegram to EverBright, 700 Universe Boulevard, Juno Beach, FL 33408, not later than midnight of May 29, 2024. I hereby cancel this transaction. ______________________________ Date ______________________________ THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 24 159415178v1 EXHIBIT B TO POWER PURCHASE AGREEMENT SCHEDULE OF VALUES Year Monthly Payment (including Annual Increase) 1 $470.00 2 $486.45 3 $503.48 4 $521.10 5 $539.34 6 $558.21 7 $577.75 8 $597.97 9 $618.90 10 $640.56 11 $662.98 12 $686.19 13 $710.20 14 $735.06 15 $760.79 16 $787.41 17 $814.97 18 $843.50 19 $873.02 20 $903.58 21 $935.20 22 $967.93 23 $1,001.81 24 $1,036.87 25 $1,073.16 THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 25 159415178v1 EXHIBIT B TO POWER PURCHASE AGREEMENT SCHEDULE OF VALUES - continued Year System Prepayment Price 1 System Buyout Price 2 1 $114,766.62 N/A 2 $114,682.47 N/A 3 $114,385.51 N/A 4 $113,857.62 N/A 5 $113,079.41 N/A 6 $112,030.34 $112,030.34 7 $110,688.37 $110,688.37 8 $109,030.17 $109,030.17 9 $107,030.89 $107,030.89 10 $104,664.12 $104,664.12 11 $101,901.77 $101,901.77 12 $98,713.93 $98,713.93 13 $95,069.01 $95,069.01 14 $90,933.25 $90,933.25 15 $86,270.87 $86,270.87 16 $81,044.03 $81,044.03 17 $75,212.34 $75,212.34 18 $68,733.00 $68,733.00 19 $61,560.73 $61,560.73 20 $53,647.35 $53,647.35 21 $44,941.97 $44,941.97 22 $35,390.47 $35,390.47 23 $24,935.50 $24,935.50 24 $13,516.37 $13,516.37 25 $1,068.71 $1,068.71 1 Per Section 9(b), in addition to the values listed, the Prepayment Price also includes accrued but unpaid sums and additional applicable taxes. The values listed assume that prepayment occurs in month 12 of the applicable year. Actual prepayment amount will be calculated based on the number of payments made and the number of payments that remain. 2 Per Section 8(c) shown above as the Minimum Buyout Price. THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 26 159415178v1 EXHIBIT C TO POWER PURCHASE AGREEMENT GUARANTEED OUTPUT End of Year Credit per kWh if Guaranteed Output is not met 3 Guaranteed Output (in kWh) 2 $0.331 29,466 4 $0.358 29,173 6 $0.388 28,882 8 $0.419 28,593 10 $0.454 28,308 12 $0.491 28,026 14 $0.531 27,746 16 $0.575 27,470 18 $0.622 27,196 20 $0.673 26,924 22 $0.728 26,656 24 $0.788 26,390 3 The actual credit rate will be the weighted average $/kWh for the applicable 24 -month period. THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 27 159415178v1 EXHIBIT D TO POWER PURCHASE AGREEMENT Payment Method Election Form YOU MUST SELECT ONE OPTION ONLY BY CHECKING THE APPROPRIATE BOX AND SIGNING BELOW Option 1 : Automatic Electronic Recurring Payments @contact_1_rb_1_g_1# By checking this box, you acknowledge that: 1. We will provide you a monthly bill detailing the amount you owe for that billing period . Under federal law, you have the right to stop an automatic payment from your bank account, provided you give your financial ice before the scheduled payment date . 2. The actual settlement date (the date the automatic electronic payment is deducted from your bank account) will be no earlier than your payment due date as stated on the invoice . We shall bear no liability or respon sibility for any losses of any kind that you may incur due to any delay in the actual date on which your bank account is debited . 3. If the due date for payments under your agreement has passed, you give us authority to withdraw two payments from your account on your next due date so that your account will be current on an ongoing basis. 4. If the due date falls on a weekend or holiday in any month, your payment will be debited the following business day . 5. In order to process automatic payments, you must have sufficient available and collected funds in your bank account on the business day before the payment due date and on the payment due date in order to cover the amount of the monthly payment that is due. 6. You must notify us immediately if the automatic payment information you provide changes . 7. We reserve the right to change these conditions at any time . Notice may be given on or with your monthly bill or by other methods . Either party may terminate this payment arrangement at any time by giving the ot her party written notice at least fifteen (15 ) days prior to the next scheduled payment date. 8. You agree to be bound by any rules your financial institution requires for automatic electronic payments . Below is your account information for the bank account at financial institution: @contact_1_text_1_cond_radio_button_group_1_condvalue_1# to be used for the automatic electronic payments. Account Number: @contact_1_protected_2_label_account -number_cond_radio_button_group_1_condvalue_1_regextype_accountnumber# Routing Number: @contact_1_protected_1_label_routing -number_cond_radio_button_group_1_condvalue_1_regextype_routingnumber# 9. You are responsible for any fees your financial institution may charge you for electronic payments. 10. By signing below, you (a) authorize us to automatically deduct your monthly payments from your bank account provided above, (b) agree to the terms and conditions herein, (c) represent to us that you have obtained any required consents from other persons with an ownership interest in the bank accou nt, and (d) represent to us that you are individual authorized to sign this automatic electronic payment THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 28 159415178v1 EXHIBIT D TO POWER PURCHASE AGREEMENT Payment M ethod Election Form - Continued Option 2 : Check by Mail @contact_1_rb_2 _g_1# By checking this box, you acknowledge that: 1. Checks should be made payable to EverBright. 2. Checks should be sent to the address listed below for your Monthly Payment by the date the payment is due . This payment address is also listed on the bill you receive for your Monthly Payment. EverBright PO Box 845073 Dallas, TX 75284 -5073 Fees: 1. Late Payment Fee : If you fail to make any payment when due, we will impose a late fee equal to the lesser of (i) one and half percent (1.5%) per month on the portion of your balance that is more than thirty (30) days past due, and (ii) the maximum amount permitted under and subject to applicable law . @contact_1_sig_3# @contact_2_sig_3# First Authorized Account Holder Signature Second Authorized Account Holder Signature ALBERT W HUMPHREY Printed Name Printed Name @contact_1_datesig_3# @contact_2_datesig_3# Date Date THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W Contract ID #5a30b443 Massachusetts PPA EverFixed , rev. 0 7 /1 0 /2023 29 159415178v1 EXHIBIT E TO POWER PURCHASE AGREEMENT DATA USAGE AND DISCLOSURE This Exhibit E describes the circumstances in which, and purposes for which, we may use or disclose Data . a. Data Usage: We may use Data for the following purposes (in each case to the extent permitted by law): 1. to operate, maintain, provide, and enhance the System; 2. for our internal purposes, including, without limitation, research and development, improvement of our produc t and service offerings, and creation of new product and service offerings; 3. to customize content and communications we may provide to you; and 4. for other purposes so long as the Data does not contain personally identifiable information (including where Data has been deidentified). b. Data Disclosure. We will not disclose any Data other than in the following circumstances: 1. where the Data does not contain personally identifiable information (including where Data has been deidentified); 2. in order to provide our products or services to you (including working with third -party service providers who may assist us in collecting, hosting, maintaining, anal yzing, or otherwise processing Data for us); 3. if required to do so by any law or regulation or in the good -faith belief that such action is necessary to comply with any law or regulation, in response to a court order, judicial or other government subpoena o r warrant, or to otherwise cooperate with law enforcement or other governmental agencies; 4. if we believe, in good faith, disclosure is appropriate or necessary to (A) take precautions against liability, (B) protect us or others from fraudulent, abusive, or unlawful uses or activity, (C) investigate or defend against any third -party claims or allegations, (D) protect the security or integrity of our services and any facilities or equipment used to make our service available, or (E) protect our property or ot her legal rights (including, but not limited to, enforcement of our agreements), or the rights, property, or safety of others; 5. to our assignees, affiliates, actual or prospective lenders, financing parties, investors, insurers, and acquirers; 6. to contract ors, service providers and other third parties we use to support our business and who are bound by contractual obligations to keep personal information confidential and use it only for the purposes for which we disclose it to them; and 7. for any purpose for which you have provided your express consent. Your initials indicate that you have read, understood and accepted the provisions set forth in this Exhibit E. Agreed and accepted by: @contact_1_init_8 # (Initials) @contact_2_init_8 # (Initials) THIS IS A COPY The Authoritative Copy of this record is held at NA4.docusign.net COP Y VI E W