Loading...
com_cerceg_instshtWARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product. Hubbell Lighting, Inc. Life Safety Products • www.compasslightingproducts.com Copyright© Hubbell Lighting, Inc., All Rights Reserved • Specifications subject to change without notice. • Printed in U.S.A. COMP0002_INST_SHT 7/12 LED Emergency Exit CER/CEG/CERRC/CEGRC IMPORTANT SAFEGUARDSWhen using electrical equipment, basic safety precautions should always be followed including the following. READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. Do not let power supply cords touch hot surfaces. 2. Do not mount near gas or electric heaters. 3. Equipment should be mounted in locations and at heights where it will not readily be subject to tampering by unauthorized personnel. 4. The use of accessory equipment not authorized by the manufacturer may cause an unsafe condition. 5. Do not use this equipment for other than its intended purpose. 6. Servicing of this equipment should be performed by qualified service personnel. INSTALLER: •SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT RECYCLING INFORMATION All steel, aluminum and thermoplastic parts are recyclable. All cartons contain recycled materials. Please recycle responsibly. INSTALLATION Ceiling & End Mounting (FIG. A) & (Fig. B). 1. Connect input as shown in wiring diagram below and fasten canopy to J-box bracket. 2. Snap housing to canopy. 3. Secure faceplate to housing and remove the proper arrow as required. WIRING DIAGRAM CER/CEG CERRC/CEGRC Warning: Unused wires must be capped using enclosed wire nuts. Hubbell Lighting, Inc., All Rights Reserved • Specifications subject to change without notice. • Printed in Hubbell Lighting, Inc. WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product. Hubbell Lighting, Inc. Life Safety Products • www.compasslightingproducts.com Copyright©COMP0002_INST_SHT 7/12 LED Emergency Exit CER/CEG/CERRC/CEGRC IMPORTANT SAFEGUARDSWhen using electrical equipment, basic safety precautions should always be followed including the following.READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. Do not let power supply cords touch hot surfaces. 2. Do not mount near gas or electric heaters. 3. Equipment should be mounted in locations and at heights where it will not readily be subject to tampering by unauthorized personnel. 4. The use of accessory equipment not authorized by the manufacturer may cause an unsafe condition. 5. Do not use this equipment for other than its intended purpose. 6. Servicing of this equipment should be performed by qualified service personnel. INSTALLER: •SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT RECYCLING INFORMATION All steel, aluminum and thermoplastic parts are recyclable. All cartons contain recycled materials. Please recycle responsibly. INSTALLATION Ceiling & End Mounting (FIG. A) & (Fig. B). 1. Connect input as shown in wiring diagram below and fasten canopy to J-box bracket. 2. Snap housing to canopy. 3. Secure faceplate to housing and remove the proper arrow as required. INSTALLATION INSTRUCTIONS FOREMERGENCYEXITSIGNIMPORTANT:When relamping, only use lamps specified in the exit sign.Using other lamp types may result in transformer damage or unsafe conditions. Battery in this unit may not be fully charged. After electricity is hooked up to unit,let the battery charge up for at least 24hours. Then normal operation of this unit should take effect. IMPORTANTSAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READAND FOLLOWALLSAFETYINSTRUCTIONS 1) Do not use outdoors. 2) Do not mount near gas or electric heaters. 3) Use caution when handling batteries.Avoid possible shorting. 4) Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel. 5) The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 6) Do not use this equipment for other than its intended use. 7) Before wiring to power supply, turn off electricity at fuse or circuit breaker. 8) Consult local building code for approved wiring and installation. 9) Installation and servicing should be performed by qualified personnel. SAVETHESE INSTRUCTIONS INSTALLATION INSTRUCTIONS CEILING & END MOUNTING (FIG.1) & (FIG.2). 1) Connect input as shown in wiring diagram below and fasten canopy to J-box bracket. 2) Snap housing to canopy. 3) Secure faceplate to housing and remove the proper arrow as required. Wiring diagram (FIG.1) (FIG.2) BLACK 120VAC WARNING: Unused wires must be capped using enclosed wire nuts. LED BOARD RED 277VAC WHITE COM BAT.T R S2.4V 400MAH INSTALLATION INSTRUCTIONS FOREMERGENCYEXITSIGNIMPORTANT:When relamping, only use lamps specified in the exit sign.Using other lamp types may result in transformer damageor unsafe conditions.Battery in this unit may not be fully charged.After electricity is hooked up to unit,let the batterycharge up for at least 24hours.Then normal operation of this unit should take effect.IMPORTANTSAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READAND FOLLOWALLSAFETYINSTRUCTIONS 1) Do not use outdoors. 2) Do not mount near gas or electric heaters. 3) Use caution when handling batteries.Avoid possible shorting. 4) Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel. 5) The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 6) Do not use this equipment for other than its intended use. 7) Before wiring to power supply, turn off electricity at fuse or circuit breaker. 8) Consult local building code for approved wiring and installation. 9) Installation and servicing should be performed by qualified personnel. SAVETHESE INSTRUCTIONS INSTALLATION INSTRUCTIONS CEILING & END MOUNTING (FIG.1) & (FIG.2). 1) Connect input as shown in wiring diagram below and fasten canopy to J-box bracket. 2) Snap housing to canopy. 3) Secure faceplate to housing and remove the proper arrow as required. Wiring diagram (FIG.1) (FIG.2) BLACK 120VAC WARNING: Unused wires must be capped using enclosed wire nuts. LED BOARD RED 277VAC WHITE COM BAT.T R S 2.4V 400MAH INSTALLATION INSTRUCTIONS FOREMERGENCYEXITSIGNIMPORTANT:When relamping, only use lamps specified in the exit sign.Using other lamp types may result in transformer damageor unsafe conditions.Battery in this unit may not be fully charged.After electricity is hooked up to unit,let the batterycharge up for at least 24hours.Then normal operation of this unit should take effect.IMPORTANTSAFEGUARDSWhen using electrical equipment, basic safety precautions should always be followed, including the following:READAND FOLLOWALLSAFETYINSTRUCTIONS1) Do not use outdoors. 2) Do not mount near gas or electric heaters. 3) Use caution when handling batteries.Avoid possible shorting. 4) Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel. 5) The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 6) Do not use this equipment for other than its intended use. 7) Before wiring to power supply, turn off electricity at fuse or circuit breaker. 8) Consult local building code for approved wiring and installation. 9) Installation and servicing should be performed by qualified personnel. SAVETHESE INSTRUCTIONS INSTALLATION INSTRUCTIONS CEILING & END MOUNTING (FIG.1) & (FIG.2). 1) Connect input as shown in wiring diagram below and fasten canopy to J-box bracket. 2) Snap housing to canopy. 3) Secure faceplate to housing and remove the proper arrow as required. Wiring diagram (FIG.1) (FIG.2) BLACK 120VAC WARNING: Unused wires must be capped using enclosed wire nuts. LED BOARD RED 277VAC WHITE COM BAT.T R S2.4V 400MAH WIRING DIAGRAM CER/CEG CERRC/CEGRC Warning:Unused wires must be capped using enclosed wire nuts. Fig. A Fig. B INSTALLATION INSTRUCTIONS FOREMERGENCYEXITSIGNIMPORTANT:When relamping, only use lamps specified in the exit sign.Using other lamp types may result in transformer damage or unsafe conditions. IMPORTANTSAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READAND FOLLOWALLSAFETYINSTRUCTIONS 1) Do not use outdoors. 2) Do not mount near gas or electric heaters. 3) Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel. 4) The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 5) Do not use this equipment for other than its intended use. 6) Before wiring to power supply, turn off electricity at fuse or circuit breaker. 7) Consult local building code for approved wiring and installation. 8) Installation and servicing should be performed by qualified personnel. SAVETHESE INSTRUCTIONS INSTALLATION INSTRUCTIONS CEILING & END MOUNTING (FIG.1) & (FIG.2). 1) Connect input as shown in wiring diagram below and fasten canopy to J-box bracket. 2) Snap housing to canopy. 3) Mount four emote lamp head at most.R Wiring diagram (FIG.1) (FIG.2) WARNING: Unused wires must be capped using enclosed wire nuts. 4) Secure faceplate to housing and remove the proper arrow as required. BLACK 120VAC LED BOARD RED 277VAC WHITE COM T R S REDBLACKREDBLACKREMOTE BAT.3.6V 1800mAH RED(+)BLACK(-)7. Do not use outdoors. China. Hubbell Lighting, Inc., All Rights Reserved • Specifications subject to change without notice. • Printed in Hubbell Lighting, Inc. WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product. Hubbell Lighting, Inc. Life Safety Products • www.compasslightingproducts.com Copyright©COMP0002_INST_SHT 7/12 LED Emergency Exit CER/CEG/CERRC/CEGRC IMPORTANT SAFEGUARDSWhen using electrical equipment, basic safety precautions should always be followed including the following.READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. Do not let power supply cords touch hot surfaces. 2. Do not mount near gas or electric heaters. 3. Equipment should be mounted in locations and at heights where it will not readily be subject to tampering by unauthorized personnel. 4. The use of accessory equipment not authorized by the manufacturer may cause an unsafe condition. 5. Do not use this equipment for other than its intended purpose. 6. Servicing of this equipment should be performed by qualified service personnel. INSTALLER: •SEE UNIT LABEL FOR ADDITIONAL MODEL SPECIFICATIONS•SAVE THESE INSTRUCTIONS FOR USE BY OWNER/OCCUPANT RECYCLING INFORMATION All steel, aluminum and thermoplastic parts are recyclable. All cartons contain recycled materials. Please recycle responsibly. INSTALLATION Ceiling & End Mounting (FIG. A) & (Fig. B). 1. Connect input as shown in wiring diagram below and fasten canopy to J-box bracket. 2. Snap housing to canopy. 3. Secure faceplate to housing and remove the proper arrow as required. INSTALLATION INSTRUCTIONS FOREMERGENCYEXITSIGNIMPORTANT:When relamping, only use lamps specified in the exit sign.Using other lamp types may result in transformer damage or unsafe conditions. Battery in this unit may not be fully charged. After electricity is hooked up to unit,let the battery charge up for at least 24hours. Then normal operation of this unit should take effect. IMPORTANTSAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READAND FOLLOWALLSAFETYINSTRUCTIONS 1) Do not use outdoors. 2) Do not mount near gas or electric heaters. 3) Use caution when handling batteries.Avoid possible shorting. 4) Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel. 5) The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 6) Do not use this equipment for other than its intended use. 7) Before wiring to power supply, turn off electricity at fuse or circuit breaker. 8) Consult local building code for approved wiring and installation. 9) Installation and servicing should be performed by qualified personnel. SAVETHESE INSTRUCTIONS INSTALLATION INSTRUCTIONS CEILING & END MOUNTING (FIG.1) & (FIG.2). 1) Connect input as shown in wiring diagram below and fasten canopy to J-box bracket. 2) Snap housing to canopy. 3) Secure faceplate to housing and remove the proper arrow as required. Wiring diagram (FIG.1) (FIG.2) BLACK 120VAC WARNING: Unused wires must be capped using enclosed wire nuts. LED BOARD RED 277VAC WHITE COM BAT.T R S2.4V 400MAH INSTALLATION INSTRUCTIONS FOREMERGENCYEXITSIGNIMPORTANT:When relamping, only use lamps specified in the exit sign.Using other lamp types may result in transformer damageor unsafe conditions.Battery in this unit may not be fully charged.After electricity is hooked up to unit,let the batterycharge up for at least 24hours.Then normal operation of this unit should take effect.IMPORTANTSAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READAND FOLLOWALLSAFETYINSTRUCTIONS 1) Do not use outdoors. 2) Do not mount near gas or electric heaters. 3) Use caution when handling batteries.Avoid possible shorting. 4) Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel. 5) The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 6) Do not use this equipment for other than its intended use. 7) Before wiring to power supply, turn off electricity at fuse or circuit breaker. 8) Consult local building code for approved wiring and installation. 9) Installation and servicing should be performed by qualified personnel. SAVETHESE INSTRUCTIONS INSTALLATION INSTRUCTIONS CEILING & END MOUNTING (FIG.1) & (FIG.2). 1) Connect input as shown in wiring diagram below and fasten canopy to J-box bracket. 2) Snap housing to canopy. 3) Secure faceplate to housing and remove the proper arrow as required. Wiring diagram (FIG.1) (FIG.2) BLACK 120VAC WARNING: Unused wires must be capped using enclosed wire nuts. LED BOARD RED 277VAC WHITE COM BAT. T R S 2.4V 400MAH INSTALLATION INSTRUCTIONS FOREMERGENCYEXITSIGNIMPORTANT:When relamping, only use lamps specified in the exit sign.Using other lamp types may result in transformer damageor unsafe conditions.Battery in this unit may not be fully charged.After electricity is hooked up to unit,let the batterycharge up for at least 24hours.Then normal operation of this unit should take effect.IMPORTANTSAFEGUARDSWhen using electrical equipment, basic safety precautions should always be followed, including the following:READAND FOLLOWALLSAFETYINSTRUCTIONS1) Do not use outdoors. 2) Do not mount near gas or electric heaters. 3) Use caution when handling batteries.Avoid possible shorting. 4) Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel. 5) The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 6) Do not use this equipment for other than its intended use. 7) Before wiring to power supply, turn off electricity at fuse or circuit breaker. 8) Consult local building code for approved wiring and installation. 9) Installation and servicing should be performed by qualified personnel. SAVETHESE INSTRUCTIONS INSTALLATION INSTRUCTIONS CEILING & END MOUNTING (FIG.1) & (FIG.2). 1) Connect input as shown in wiring diagram below and fasten canopy to J-box bracket. 2) Snap housing to canopy. 3) Secure faceplate to housing and remove the proper arrow as required. Wiring diagram (FIG.1) (FIG.2) BLACK 120VAC WARNING: Unused wires must be capped using enclosed wire nuts. LED BOARD RED 277VAC WHITE COM BAT.T R S2.4V 400MAH WIRING DIAGRAM CER/CEG CERRC/CEGRC Warning:Unused wires must be capped using enclosed wire nuts. Fig. A Fig. B INSTALLATION INSTRUCTIONS FOREMERGENCYEXITSIGNIMPORTANT:When relamping, only use lamps specified in the exit sign.Using other lamp types may result in transformer damage or unsafe conditions. IMPORTANTSAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READAND FOLLOWALLSAFETYINSTRUCTIONS 1) Do not use outdoors. 2) Do not mount near gas or electric heaters. 3) Equipment should be mounted in locations and at heights where it will not be subject to tampering by unauthorized personnel.4) The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 5) Do not use this equipment for other than its intended use. 6) Before wiring to power supply, turn off electricity at fuse or circuit breaker. 7) Consult local building code for approved wiring and installation. 8) Installation and servicing should be performed by qualified personnel. SAVETHESE INSTRUCTIONS INSTALLATION INSTRUCTIONS CEILING & END MOUNTING (FIG.1) & (FIG.2). 1) Connect input as shown in wiring diagram below and fasten canopy to J-box bracket. 2) Snap housing to canopy. 3) Mount four emote lamp head at most.R Wiring diagram (FIG.1) (FIG.2) WARNING: Unused wires must be capped using enclosed wire nuts. 4) Secure faceplate to housing and remove the proper arrow as required. BLACK 120VAC LED BOARD RED 277VAC WHITE COM T R S REDBLACKREDBLACKREMOTE BAT.3.6V 1800mAH RED(+)BLACK(-)7. Do not use outdoors. China.