lpp-square-straight-steel-UPDATEEngineered&Manufactured
In TheUSARev. V10032016
This specification brochure is intended to serve as a general guide. Our products are continually being engineered and improved, and specifications are subject to change without notice.
Project Name
Catalog #
Pole Type
Product Overview
• Pole Shaft - The pole shaft is fabricated from hot rolled welded steel tubing of one-piece construction with a minimum yield strength of 55 KSI.
• Pole Top - A removable top cap is provided for poles receiving drilling patterns for side-mount luminaire
arm assemblies. Other pole top options include Tenon Top, Top Cap Only or Open Top which is typical when the pole top diameter matches the necessary slip-fit dimensions.
• Hand Hole - A reinforced hand hole with grounding provision is provided at 1’-6” from the base end of the pole assembly. Each hand hole includes a cover and cover attachment hardware. All pole assemblies are provided with a 2.5” x 5” rectangular hand hole (dimensions are nominal).
• Base Cover - A two-piece full base cover fabricated from ABS plastic is provided with each pole assembly. Additional base cover options, including a cast aluminum and fabricated steel cover, are available upon request.
• Anchor Bolts - Anchor bolts conform to ASTM F1554 Grade 55 and are provided with two hex nuts and two flat washers. Bolts have an “L” bend on one end and are galvanized a minimum of 12” on the
threaded end.
• Hardware - All structural fasteners are galvanized high strength carbon steel. All non-structural fasteners are galvanized or zinc-plated carbon steel or stainless steel.
• Finish - Standard finishes are either Galvanized or Finish Painted. Additional finish options including Finish Paint over Galvanizing are available upon request.
• Design Criteria - Standard EPA (Effective Projected Area) and weight values are based on Standard Commercial Criteria (with 1.3 gust factor) for side mounted fixtures only. Consult the factory on loading criteria for pole top mounted luminaires and/or brackets. Satisfactory performance of light poles is dependent upon the pole being properly attached to a supporting foundation of adequate design.
Square Straight Steel Light Poles
206 W. McWilliams St.Suite 101Fond du Lac, WI 54935
888-791-1463quotes@lightpolesplus.comLightPolesPlus.com
This specification brochure is intended to serve as a general guide. Our products are continually being engineered and improved, and specifications are subject to change without notice.
Engineered&Manufactured
In TheUSARev. V10032016
Designation & Dimensional Information
EPA Load Information
1. The total combined EPA and weight of all fixtures, brackets and attachments mounting to a light pole cannot exceed the EPA and weight rating for a specified pole.
2. Standard EPA (Effective Projected Area) and weight values are based on Standard Commercial Criteria (with 1.3 gust factor) for side mounted fixtures only. Consult the factory on loading criteria for pole top mounted luminaires and/or brackets.
3. Satisfactory performance of light poles is dependent upon the pole being properly attached to a supporting foundation of adequate design.
Note: Additional sizes and configurations are available upon request.
"+" Indicates a vibration dampener is standard
80 MPH w/1.3 GUST 90 MPH w/1.3 GUST 100 MPH w/1.3 GUST
MAX EPA (SQFT)MAX WEIGHT (LBS)MAX EPA (SQFT)MAX WEIGHT (LBS)MAX EPA (SQFT)MAX WEIGHT (LBS)
30.6 765 23.8 595 18.9 473
24.4 610 18.8 470 14.8 370
19.9 498 15.1 378 11.7 293
15.9 398 11.8 295 8.9 223
15.9 398 11.8 295 8.9 223
12.6 315 9.2 230 6.7 168
9.6 240 6.7 167 4.5 150
15.8 240 12.7 167 9 150
17.7 443 12.7 343 9.4 235
28.1 703 21.4 535 16.2 405
4.8 150 2.6 100 1 50
10.8 270 7.7 188 5.4 135
9.8 245 6.3 157 3.7 150
18.5 463 13.3 333 9.5 238
6.7 168 4.4 110 2.6 65
4.7 150 2 50 N/A N/A
10.7 267 6.7 167 3.9 100
19 475 13.2 330 9 225
5.9 150 2.5 100 N/A N/A
12.4 310 7.6 190 4.2 105
7.2 180 3 75 N/A N/A
POLE DIMENSIONS BASE PLATE ANCHOR BOLTS
NOMINAL MOUNTING HEIGHT
TOP SQ (IN)BASE SQ (IN)
WALL THK (GA)
STRUCTURE WEIGHT (LBS)
BOLTCIRCLEDIA (IN)SQ (IN) x THICK (IN)DIA x LENGTH x HOOK (IN)PROJECTION (IN)
10’-0”4 4 11 75 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75
12’-0”4 4 11 90 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75
14’-0”4 4 11 100 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75
15’-0”4 4 11 110 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75
16’-0”4 4 11 115 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75
18’-0”4 4 11 125 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75
20’-0”4 4 11 140 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75
20’-0”4 4 7 200 8.0 - 9.0 8.25 x 0.875 0.75 x 17.00 x 3.00 3.38 - 3.88
20’-0”5 5 11 185 10.0 - 12.0 11 x 1 0.75 x 17.00 x 3.00 3.5 - 4
20’-0”5 5 7 265 10.0 - 12.0 11 x 1 0.75 x 17.00 x 3.00 3.5 - 4
25’-0”4 4 11 170 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75
25’-0”4 4 7 245 8.0 - 9.0 8.25 x 0.875 0.75 x 17.00 x 3.00 3.38 - 3.88
25’-0”5 5 11 225 10.0 - 12.0 11 x 1 0.75 x 17.00 x 3.00 3.5 - 4
25’-0”5 5 7 360 10.0 - 12.0 11 x 1 0.75 x 17.00 x 3.00 3.5 - 4
30’-0”4 4 7 291 8.0 - 9.0 8.25 x 0.875 0.75 x 17.00 x 3.00 3.38 - 3.88
30’-0”5 5 11 265 10.0 - 12.0 11 x 1 0.75 x 17.00 x 3.00 3.5 - 4
30’-0”5 5 7 380 10.0 - 12.0 11 x 1 0.75 x 17.00 x 3.00 3.5 - 4
30’-0”6 6 7 520 11.0 - 13.0 12.5 x 1 1.00 x 36.00 x 4.00 4 - 4.5
35’-0”5 5 7 440 10.0 - 12.0 11 x 1 0.75 x 17.00 x 3.00 3.5 - 4
35’-0”6 6 7 540 11.0 - 13.0 12.5 x 1 1.00 x 36.00 x 4.00 4 - 4.5
40’-0”6 6 7 605 11.0 - 13.0 12.5 x 1 1.00 x 36.00 x 4.00 4 - 4.5
206 W. McWilliams St.Suite 101Fond du Lac, WI 54935
888-791-1463quotes@lightpolesplus.comLightPolesPlus.com
BASE MODEL
SSSA-10-4040-11
SSSA-12-4040-11
SSSA-14-4040-11
SSSA-15-4040-11
SSSA-16-4040-11
SSSA-18-4040-11
SSSA-20-4040-11
SSSA-20-4040-7
SSSA-20-5050-11
SSSA-20-5050-7
SSSA-25-4040-11
SSSA-25-4040-7
SSSA-25-5050-11
SSSA-25-5050-7
SSSA-30-4040-7
SSSA-30-5050-11
SSSA-30-5050-7
SSSA-30-6060-7
SSSA-35-5050-7
SSSA-35-6060-7
SSSA-40-6060-7
BASE MODEL
SSSA-10-4040-11
SSSA-12-4040-11
SSSA-14-4040-11
SSSA-15-4040-11
SSSA-16-4040-11
SSSA-18-4040-11
SSSA-20-4040-11
SSSA-20-4040-7
SSSA-20-5050-11
SSSA-20-5050-7
SSSA-25-4040-11
SSSA-25-4040-7
SSSA-25-5050-11
SSSA-25-5050-7
SSSA-30-4040-7
SSSA-30-5050-11
SSSA-30-5050-7
SSSA-30-6060-7
SSSA-35-5050-7
SSSA-35-6060-7
SSSA-40-6060-7
This specification brochure is intended to serve as a general guide. Our products are continually being engineered and improved, and specifications are subject to change without notice.
Ordering Information
Options & Accessories
Engineered&Manufactured
In TheUSARev. V10032016
Note: Please consult factory or your sales representative to verify options and accessories will work with your light pole part number.
* See previous pages for base model configurations. Consult factory or your sales rep for deviations from base models. Additional sizes and configurations available upon request.
206 W. McWilliams St.Suite 101Fond du Lac, WI 54935
888-791-1463quotes@lightpolesplus.comLightPolesPlus.com
Ex. SSSA-20-4040-7-FP-DB-D1
Designation
SSSA =Square Straight Steel
Length*
10 to 40
Base OD*
40 =4”
50 =5”
60 =6”
Top OD*
40 =4”
50 =5”
60 =6”
Finish Type
GV =Galvanzied Only (No Paint)
FP =Finish Painted
FPGV =Finish Paint over Galvanizing
Thickness*
7 =7ga
11 =11ga
Painted Color
DB =Dark Bronze
MB =Medium Bronze
LG =Light Gray
DG =Dark Green
HG =Hunter Green
SG =Slate Gray
SM =Silver Metallic
BK =Black
WH =White
SL =Silver
SC = Custom
Fixture Mounting
Drill Mounting (includes cap)
D1 =Single
D2 =2@180 deg.
D3 =3@120 deg.
D4 =4@90 deg.
D5 =2@90 deg.
D6 =3@90 deg.
Tenon Mounting
P1 =4” OD x 5” Long Tenon
P2 =2.38” OD x 4” Long Tenon
P3 =3.50” OD x 6” Long Tenon
P4 =4” OD x 6” Long Tenon
P5 =2.88” OD x 4” Long Tenon
P6 =2.88” OD x 5” Long Tenon
P7 =2.38” OD x 5” Long Tenon
PQ =2.38” OD x 12” Long Tenon
PD =3” OD x 3” Long Tenon
P9 =Custom Size Tenon
Other Options
PC =Cap Only, No Side Drilling
PL =Open Top, No Cap or Side Drilling
Description
LAB10 =Less Anchor Bolts - 1" x 36" x 4"
LAB75 =Less Anchor Bolts - 0.75" x 17" x 3"
SPL =Special Length (Please Specify)
BCSPCL =Special Base Plate to Match Existing Bolt Circle (May Add 2 Weeks to Production Lead Time, May Require Special Base Cover)
VD =Internal Vibration Dampener, Factory Installed
VDF =Internal Vibration Dampener, Field Installable
FBCS =Steel Full Base Cover
FBCP =ABS Plastic Full Base Cover
Description
ULHH =UL Compliant Hand Hole
NECHH =NEC 410.30 Compliant Hand Hole & Cover
EHH =Additional Hand Hole Opening w/ Cover Assembly(Specify Pole Height & Orientation)
FST =Festoon Provision, Electrical by Others(Specify Pole Height & Orientation)
CPL =NPT Pipe Coupling(Specify Pole Height, Orientation & NPT Size)
PXDX =Side Drill + Tenon w/ Additional Hand Hole (Specify Tenon OD & Length)
Description
FOUNDATION =Engineering Services, Foundation Design
STAMP =Engineering Services, Signed & Sealed Calcs
STAMPCA =Engineering Services, CA Signed & Sealed Calcs