relightpolebases
lpp-square-straight-steel.pdf
Engineered & Manufactured In The USA Rev. V10032016 This specification brochure is intended to serve as a general guide. Our products are continually being engineered and improved, and
specifications are subject to change without notice. Project Name Catalog # Pole Type Product Overview • Pole Shaft - The pole shaft is fabricated from hot rolled welded steel tubing
of one-piece construction with a minimum yield strength of 55 KSI. • Pole Top - A removable top cap is provided for poles receiving drilling patterns for side-mount luminaire arm assemblies.
Other pole top options include Tenon Top, Top Cap Only or Open Top which is typical when the pole top diameter matches the necessary slip-fit dimensions. • Hand Hole - A reinforced
hand hole with grounding provision is provided at 1’-6” from the base end of the pole assembly. Each hand hole includes a cover and cover attachment hardware. All pole assemblies are
provided with a 2.5” x 5” rectangular hand hole (dimensions are nominal). • Base Cover - A two-piece full base cover fabricated from ABS plastic is provided with each pole assembly.
Additional base cover options, including a cast aluminum and fabricated steel cover, are available upon request. • Anchor Bolts - Anchor bolts conform to ASTM F1554 Grade 55 and are
provided with two hex nuts and two flat washers. Bolts have an “L” bend on one end and are galvanized a minimum of 12” on the threaded end. • Hardware - All structural fasteners are
galvanized high strength carbon steel. All non-structural fasteners are galvanized or zinc-plated carbon steel or stainless steel. • Finish - Standard finishes are either Galvanized
or Finish Painted. Additional finish options including Finish Paint over Galvanizing are available upon request. • Design Criteria - Standard EPA (Effective Projected Area) and weight
values are based on Standard Commercial Criteria (with 1.3 gust factor) for side mounted fixtures only. Consult the factory on loading criteria for pole top mounted luminaires and/or
brackets. Satisfactory performance of light poles is dependent upon the pole being properly attached to a supporting foundation of adequate design. Square Straight Steel Light Poles
206 W. McWilliams St. Suite 101 Fond du Lac, WI 54935 888-791-1463 quotes@lightpolesplus.com LightPolesPlus.com This specification brochure is intended to serve as a general guide.
Our products are continually being engineered and improved, and specifications are subject to change without notice. Engineered & Manufactured In The USA Rev. V10032016 Designation
& Dimensional Information EPA Load Information 1. The total combined EPA and weight of all fixtures, brackets and attachments mounting to a light pole cannot exceed the EPA and weight
rating for a specified pole. 2. Standard EPA (Effective Projected Area) and weight values are based on Standard Commercial Criteria (with 1.3 gust factor) for side mounted fixtures
only. Consult the factory on loading criteria for pole top mounted luminaires and/or brackets. 3. Satisfactory performance of light poles is dependent upon the pole being properly attached
to a supporting foundation of adequate design. Note: Additional sizes and configurations are available upon request. "+" Indicates a vibration dampener is standard 80 MPH w/1.3 GUST
90 MPH w/1.3 GUST 100 MPH w/1.3 GUST MAX EPA (SQFT) MAX WEIGHT (LBS) MAX EPA (SQFT) MAX WEIGHT (LBS) MAX EPA (SQFT) MAX WEIGHT (LBS) 30.6 765 23.8 595 18.9 473 24.4 610 18.8 470 14.8
370 19.9 498 15.1 378 11.7 293 15.9 398 11.8 295 8.9 223 15.9 398 11.8 295 8.9 223 12.6 315 9.2 230 6.7 168 9.6 240 6.7 167 4.5 150 15.8 240 12.7 167 9 150 17.7 443 12.7 343 9.4 235
28.1 703 21.4 535 16.2 405 4.8 150 2.6 100 1 50 10.8 270 7.7 188 5.4 135 9.8 245 6.3 157 3.7 150 18.5 463 13.3 333 9.5 238 6.7 168 4.4 110 2.6 65 4.7 150 2 50 N/A N/A 10.7 267 6.7 167
3.9 100 19 475 13.2 330 9 225 5.9 150 2.5 100 N/A N/A 12.4 310 7.6 190 4.2 105 7.2 180 3 75 N/A N/A POLE DIMENSIONS BASE PLATE ANCHOR BOLTS NOMINAL MOUNTING HEIGHT TOP SQ (IN) BASE
SQ (IN) WALL THK (GA) STRUCTURE WEIGHT (LBS) BOLTCIRCLE DIA (IN) SQ (IN) x THICK (IN) DIA x LENGTH x HOOK (IN) PROJECTION (IN) 10’-0” 4 4 11 75 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x
3.00 3.25 - 3.75 12’-0” 4 4 11 90 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75 14’-0” 4 4 11 100 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75 15’-0” 4 4 11 110 8.0
- 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75 16’-0” 4 4 11 115 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75 18’-0” 4 4 11 125 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00
3.25 - 3.75 20’-0” 4 4 11 140 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75 20’-0” 4 4 7 200 8.0 - 9.0 8.25 x 0.875 0.75 x 17.00 x 3.00 3.38 - 3.88 20’-0” 5 5 11 185 10.0 -
12.0 11 x 1 0.75 x 17.00 x 3.00 3.5 - 4 20’-0” 5 5 7 265 10.0 - 12.0 11 x 1 0.75 x 17.00 x 3.00 3.5 - 4 25’-0” 4 4 11 170 8.0 - 9.0 8.25 x 0.75 0.75 x 17.00 x 3.00 3.25 - 3.75 25’-0”
4 4 7 245 8.0 - 9.0 8.25 x 0.875 0.75 x 17.00 x 3.00 3.38 - 3.88 25’-0” 5 5 11 225 10.0 - 12.0 11 x 1 0.75 x 17.00 x 3.00 3.5 - 4 25’-0” 5 5 7 360 10.0 - 12.0 11 x 1 0.75 x 17.00 x
3.00 3.5 - 4 30’-0” 4 4 7 291 8.0 - 9.0 8.25 x 0.875 0.75 x 17.00 x 3.00 3.38 - 3.88 30’-0” 5 5 11 265 10.0 - 12.0 11 x 1 0.75 x 17.00 x 3.00 3.5 - 4 30’-0” 5 5 7 380 10.0 - 12.0 11
x 1 0.75 x 17.00 x 3.00 3.5 - 4 30’-0” 6 6 7 520 11.0 - 13.0 12.5 x 1 1.00 x 36.00 x 4.00 4 - 4.5 35’-0” 5 5 7 440 10.0 - 12.0 11 x 1 0.75 x 17.00 x 3.00 3.5 - 4 35’-0” 6 6 7 540 11.0
- 13.0 12.5 x 1 1.00 x 36.00 x 4.00 4 - 4.5 40’-0” 6 6 7 605 11.0 - 13.0 12.5 x 1 1.00 x 36.00 x 4.00 4 - 4.5 206 W. McWilliams St. Suite 101 Fond du Lac, WI 54935 888-791-1463 quotes@lightpolesplus
.com LightPolesPlus.com BASE MODEL SSSA-10-4040-11 SSSA-12-4040-11 SSSA-14-4040-11 SSSA-15-4040-11 SSSA-16-4040-11 SSSA-18-4040-11 SSSA-20-4040-11 SSSA-20-4040-7 SSSA-20-5050-11 SSSA-20-5050-7
SSSA-25-4040-11 SSSA-25-4040-7 SSSA-25-5050-11 SSSA-25-5050-7 SSSA-30-4040-7 SSSA-30-5050-11 SSSA-30-5050-7 SSSA-30-6060-7 SSSA-35-5050-7 SSSA-35-6060-7 SSSA-40-6060-7 BASE MODEL SSSA-10-4040-11
SSSA-12-4040-11 SSSA-14-4040-11 SSSA-15-4040-11 SSSA-16-4040-11 SSSA-18-4040-11 SSSA-20-4040-11 SSSA-20-4040-7 SSSA-20-5050-11 SSSA-20-5050-7 SSSA-25-4040-11 SSSA-25-4040-7 SSSA-25-5050-11
SSSA-25-5050-7 SSSA-30-4040-7 SSSA-30-5050-11 SSSA-30-5050-7 SSSA-30-6060-7 SSSA-35-5050-7 SSSA-35-6060-7 SSSA-40-6060-7 This specification brochure is intended to serve as a general
guide. Our products are continually being engineered and improved, and specifications are subject to change without notice. Ordering Information Options & Accessories Engineered & Manufactured
In The USA Rev. V10032016 Note: Please consult factory or your sales representative to verify options and accessories will work with your light pole part number. * See previous pages
for base model configurations. Consult factory or your sales rep for deviations from base models. Additional sizes and configurations available upon request. 206 W. McWilliams St.
Suite 101 Fond du Lac, WI 54935 888-791-1463 quotes@lightpolesplus.com LightPolesPlus.com Ex. SSSA-20-4040-7-FP-DB-D1 Designation SSSA = Square Straight Steel Length* 10 to 40 Base
OD* 40 = 4” 50 = 5” 60 = 6” Top OD* 40 = 4” 50 = 5” 60 = 6” Finish Type GV = Galvanzied Only (No Paint) FP = Finish Painted FPGV = Finish Paint over Galvanizing Thickness* 7 = 7ga 11
= 11ga Painted Color DB = Dark Bronze MB = Medium Bronze LG = Light Gray DG = Dark Green HG = Hunter Green SG = Slate Gray SM = Silver Metallic BK = Black WH = White SL = Silver SC
= Custom Fixture Mounting Drill Mounting (includes cap) D1 = Single D2 = 2@180 deg. D3 = 3@120 deg. D4 = 4@90 deg. D5 = 2@90 deg. D6 = 3@90 deg. Tenon Mounting P1 = 4” OD x 5” Long
Tenon P2 = 2.38” OD x 4” Long Tenon P3 = 3.50” OD x 6” Long Tenon P4 = 4” OD x 6” Long Tenon P5 = 2.88” OD x 4” Long Tenon P6 = 2.88” OD x 5” Long Tenon P7 = 2.38” OD x 5” Long Tenon
PQ = 2.38” OD x 12” Long Tenon PD = 3” OD x 3” Long Tenon P9 = Custom Size Tenon Other Options PC = Cap Only, No Side Drilling PL = Open Top, No Cap or Side Drilling Description LAB10
= Less Anchor Bolts - 1" x 36" x 4" LAB75 = Less Anchor Bolts - 0.75" x 17" x 3" SPL = Special Length (Please Specify) BCSPCL = Special Base Plate to Match Existing Bolt Circle (May
Add 2 Weeks to Production Lead Time, May Require Special Base Cover) VD = Internal Vibration Dampener, Factory Installed VDF = Internal Vibration Dampener, Field Installable FBCS =
Steel Full Base Cover FBCP = ABS Plastic Full Base Cover Description ULHH = UL Compliant Hand Hole NECHH = NEC 410.30 Compliant Hand Hole & Cover EHH = Additional Hand Hole Opening
w/ Cover Assembly (Specify Pole Height & Orientation) FST = Festoon Provision, Electrical by Others (Specify Pole Height & Orientation) CPL = NPT Pipe Coupling (Specify Pole Height,
Orientation & NPT Size) PXDX = Side Drill + Tenon w/ Additional Hand Hole (Specify Tenon OD & Length) Description FOUNDATION = Engineering Services, Foundation Design STAMP = Engineering
Services, Signed & Sealed Calcs STAMPCA = Engineering Services, CA Signed & Sealed Calcs
SSSA-4IN.pdf Full page photo